2017 FIAT ® 500 ABARTH 2017 17FX24-126-AD ©2016 FCA US LLC. All Rights Reserved. FIAT is a registered trademark of FCA Group Marketing S.p.A., used under license by FCA US LLC. OWNER’S MANUAL Fourth Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully.
INTRODUCTION 5 Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual: 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 NOTE: It is illegal to remove or alter the VIN. VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . .11 ▫ Opening Power Top Remote Function . . . . . .16 ▫ Mechanical Ignition Key Removal . . . . . . . . .11 ▫ To Lock The Doors, Liftgate, And Charge Port Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 ▫ Locking Doors With A Key. . . . . . . . . . . . . . .13 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . .13 䡵 SENTRY KEY . . . . . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 OCCUPANT RESTRAINT SYSTEMS . . . . . . . . .23 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Occupant Restraint Systems Features . . . . . . .23 ▫ Transporting Passengers. . . . . . . . . . . . . . . . .64 ▫ Important Safety Precautions . . . . . . . . . . . . .23 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Seat Belt Systems . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS The key fob contains a mechanical integrated key. To use the mechanical key, simply push the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the authorized dealer that sold you your new vehicle has the key 2 code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Mechanical Ignition Key Removal 1.
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) Mechanical Ignition Switch Positions 1 — STOP (OFF/LOCK) 2 — MAR (ACC/ON/RUN) 3 — AVV (START) WARNING! • Before exiting a vehicle, always shift the automatic transmission into PARK or the manual transmission into FIRST gear or REVERSE, apply the parking brake, turn the vehicle OFF, remove the key fobs from vehicle, and lock all doors. and lock your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 CAUTION! An unlocked vehicle is an invitation. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. vehicle operation. Therefore, only keys that are programmed to the vehicle can be used to start and operate the vehicle. Locking Doors With A Key NOTE: A key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle. When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer. The VIN is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The vehicle security alarm is designed to protect your vehicle. However, you can create conditions where the vehicle security alarm will give you a false alarm. If one of the previously described arming sequences has occurred, the vehicle security alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the vehicle security alarm.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Key Unlock, Driver Door/All Doors 1st Press NOTE: The remote keyless power top function can be used to open the power top to the spoiler position. This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the unlock button on the key fob. To change the current setting, refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! (Continued) • Never place any extremities (hands, feet, etc.) near the convertible top components, the upper windshield area, the shelf area behind the rear seats, or the convertible top stowage area while raising or lowering the convertible top. • When using the power top button on key fob, if potential danger exists while lowering the top, release the button immediately to interrupt the operation.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Rotate the screw located on the side of the key fob using a small screwdriver. 3. Take out the battery case. Remove and replace the battery observing its polarity. Key Fob Screw Location Battery Case Removed 4. Reinstall the battery case inside the key fob and turn the screw to lock it into place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: 2 This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) CAUTION! the parking brake, turn the vehicle OFF, remove the key fobs from vehicle, and lock all doors. and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 POWER WINDOWS Power Window Switches There are single window controls located on the shifter bezel, below the climate controls, which operate the driver and passenger door windows. The window controls will operate when the ignition switch is in the MAR (ACC/ON/RUN) position. Power Door Lock Handle Auto Door Locks When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 12 mph (20 km/h).
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-Down The driver’s door window switch has an Auto-Down feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 NOTE: Gas props support the liftgate in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props 2 when opening the liftgate in cold weather.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 6. All occupants should always wear their lap and shoulder belts properly. 1. Children 12 years old and under should always ride buckled up in a vehicle with a rear seat. 7. The driver and front passenger seats should be moved back as far as practical to allow the front air bags room to inflate. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Seat Belt Systems Initial Indication Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and could cause a collision that includes you. This can happen far away from home or on your own street. If the driver is unbuckled when the ignition switch is first in the AVV/START or MAR/ON/RUN position, a 2 chime will signal for a few seconds.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE buckled. The BeltAlert warning sequence may repeat based on vehicle speed until the driver and occupied outboard front seat passenger seat belts are buckled. The driver should instruct all occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! (Continued) WARNING! (Continued) • In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) vehicle, take it to your authorized dealer immediately and have it fixed. • A seat belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your seat belt into the buckle nearest you. • A seat belt that is too loose will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 2 Pulling Out The Latch Plate Inserting Latch Plate Into Buckle 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate. Positioning The Lap Belt 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Seat Belt Extender Seat Belts And Pregnant Women If a seat belt is not long enough to fit properly, even when the webbing is fully extended and the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a Seat Belt Extender. The Seat Belt Extender should be used only if the existing seat belt is not long enough.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioner Switchable Automatic Locking Retractor (ALR) The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 around the occupant’s mid-section so as to not activate the ALR. If the ALR is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a ⬙click.⬙ In Automatic Locking Mode, the shoulder belt is automatically pre-locked.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 The ORC contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment. The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is in the MAR/ACC/ON/RUN position. After the self-check, the Air Bag Warning Light will turn off.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Air Bags This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger. The front air bags are a supplement to the seat belt restraint systems. The driver front air bag is mounted in the center of the steering wheel. The passenger front air bag is mounted in the instrument panel, above the glove compartment. The words “SRS AIRBAG” or “AIRBAG” are embossed on the air bag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! (Continued) extending your arms to reach the steering wheel or instrument panel. • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use a rear-facing child restraint in a vehicle with a rear seat.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, air bags won’t deploy at all. Always wear your seat belts even though you have air bags. Front Air Bag Operation Front Air Bags are designed to provide additional protection by supplementing the seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! • Do not drill, cut, or tamper with the knee impact bolsters in any way. • Do not mount any accessories to the knee impact bolsters such as alarm lights, stereos, citizen band radios, etc. 2 Supplemental Driver Knee Air Bag This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the SAB deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating SAB deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates. Children are at an even greater risk of injury from a deploying air bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 inflate. Children are at an even greater risk of injury from a deploying air bag. WARNING! • Do not stack luggage or other cargo up high enough to block the deployment of the SABICs. The trim covering above the side windows where the SABIC and its deployment path are located should remain free from any obstructions. • In order for the SABICs to work as intended, do not install any accessory items in your vehicle which could alter the roof.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) children, should never lean on or sleep against the door, side windows, or area where the side air bags inflate, even if they are in an infant or child restraint. • Seat belts (and child restraints where appropriate) are necessary for your protection in all collisions. They also help keep you in position, away from an inflating Side Air Bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • Instrument Panel • Knee Impact Bolsters • Driver and Front Passenger Air Bags • Supplemental Side Air Bags • Supplemental Knee Air Bags • Front and Side Impact Sensors • Seat Belt Pretensioners • Seat Track Position Sensors • Seat Belt Buckle Switch If A Deployment Occurs The front air bags are designed to deflate immediately after deployment. NOTE: Front and/or side air bags will not deploy in all collisions.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by your authorized dealer immediately. Also, have the Occupant Restraint Controller System serviced as well. NOTE: • Air bag covers may not be obvious in the interior trim, but they will open during air bag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Customer Action Customer Will See NOTE: Each step MUST BE held for at least two seconds 1. Turn ignition STOP/ OFF/LOCK. (Turn Signal Must be placed in Neutral State). 2. Turn ignition MAR/ Right turn light BLINKS. ACC/ON/RUN. Left turn light is OFF. 3. Turn right turn signal Right turn light is ON switch ON. SOLID. Left turn light BLINKS. 4. Place turn signal in Right turn light is OFF. neutral state. Left turn light BLINKS. 5.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a reset procedure step is not completed within 60 seconds, then the turn signal lights will blink and the reset procedure must be performed again in order to be successful. Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 • How various systems in your vehicle were operating; Child Restraints • Whether or not the driver and passenger safety belts were buckled/fastened; Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the 2 United States, and every Canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in the child restraint Owner’s Manual and on all the labels attached to the child restraint. Standards.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Larger Children Children Too Large for Child Restraints Child Size, Height, Weight or Age Children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt Children 12 years old or younger, who have out-grown the height or weight limit of their booster seat Infant And Child Restraints Safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they rea
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children And Child Restraints Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forwardfacing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether the child can use the vehicle’s seat belt alone: 1. Can the child sit all the way back against the back of the vehicle seat? 2.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Lower Anchors And Tethers For CHildren (LATCH) Restraint System these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child reuntil the combined weight of the straint) for using the LATCH anchild and the child restraint is chorage system to attach the child 65 lbs (29.5 kg). Use the seat belt restraint? and tether anchor instead of the LATCH system once the combined weight is more than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes Never “share” a LATCH anchorage with two or more child restraints.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH WARNING! This vehicle does not have a center seating position. Do not use the center lower LATCH anchorages to install a child seat in the center of the back seat. Always follow the directions of the child restraint manufacturer when installing your child restraint.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. How To Stow An Unused Switchable-ALR (ALR) Seat Belt: When using the LATCH attaching system to install a child restraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle • Improper installation or failure to properly secure a child restraint can lead to failure of the restraint. The child could be badly injured or killed. • Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child reusing the seat belt to install a forstraint) for using the Tether Anchor ward facing child restraint, up to with the seat belt to attach a forthe recommended weight limit of ward facing child restraint? the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the child seat. 2.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using The Top Tether Anchorage WARNING! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! (Continued) • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. Rear Seat Tether Strap Mounting 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “Maintenance Procedures” in “Maintaining Your Vehicle.” CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! (Continued) • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • If you are required to drive with the trunk/ liftgate/rear doors open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will illuminate with a single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault is cleared. If the light comes on intermittently or remains on while driving, have an authorized dealer service the vehicle immediately. Refer to “Occupant Restraints Systems” for further information. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 WARNING! (Continued) WARNING! (Continued) • ONLY use the driver’s side floor mat on the driver’s side floor area. To check for interference, with the vehicle properly parked with the engine off, fully depress the accelerator, the brake, and the clutch pedal (if present) to check for interference.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for proper closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 POWER CONVERTIBLE TOP — IF EQUIPPED .72 ▫ Recline Adjustment . . . . . . . . . . . . . . . . . . . .80 ▫ Lowering The Power Top. . . . . . . . . . . . . . . .72 ▫ Seat Height Adjustment . . . . . . . . . . . . . . . . .80 ▫ Raising The Power Top . . . . . . . . . . . . . . . . .73 ▫ EZ Entry Feature. . . . . . . . . . . . . . . . . . . . . .80 ▫ Power Convertible Top Relearn Procedure . . . .74 ▫ Memory Feature . . . . . . . . . . . . . . . . . .
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . .87 䡵 REAR PARK ASSIST — IF EQUIPPED . . . . . . . .96 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . .87 ▫ Rear Park Assist Sensors . . . . . . . . . . . . . . . .96 ▫ Follow Me Home/Headlight Delay. . . . . . . . .87 ▫ Rear Park Assist Warning Display. . . . . . . . . .96 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . .88 ▫ Rear Park Assist Display . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . .106 䡵 CARGO AREA FEATURES . . . . . . . . . . . . . . .107 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . .106 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . .108 ▫ Glove Compartment . . . . . . . . . . . . . . . . . .106 ▫ Rear Window Defroster . . . . . . . . . . . . . . . .
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER CONVERTIBLE TOP — IF EQUIPPED NOTE: On vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, is used to open the power top, and the driver side button, is used to close the power top. • The power top buttons will operate when the ignition switch is turned to the ACC/ON/RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 NOTE: NOTE: • Vertical movement only operates in auto open/close mode. • If the top is three-quarter of the way open, you can close the top if vehicle speeds are above 50 mph (80 km/h). • If you are traveling at speeds above 50 mph (80 km/h) and wish to open the top, it will open to only three-quarter of the way.
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • Avoid high-pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips. • Remove any standing water from the top and dry the surface before opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 If the power convertible top does not relearn, repeat the procedure a second time. Wind Stop The Wind Stop installs in the backseat area of the vehicle. The Wind Stop will not interfere with power top operation. Therefore, it can remain installed when the top is up. 3 MIRRORS Inside Day/Night Mirror The mirror can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors The power mirror controls are located on the driver’s door trim panel. Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Power Mirror Switches The power mirror controls consist of a mirror select switch and a four-way mirror control switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. 3 Spotter Mirror — If Equipped Some models are equipped with a driver’s side spotter mirror.
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature will be activated whenever you turn on the rear window defroster (if equipped). Refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle” for further information. Sun Visors The driver and passenger sun visors are located on the headliner, near the front windshield. The sun visors can be rotated downward or up against the door glass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Forward/Rearward Adjustment The adjusting bar is located at the front of the seats, near the floor.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recline Adjustment Seat Height Adjustment The recline adjustment lever is located on the inboard side of the seat. To recline the seatback, lift up the recline lever, lean back until the desired position has been reached, and release the lever. The driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 accomplished if the seat is moved fully rearward to its last fore/aft position on the tracks before the seat back is returned upright. Memory Function Option 2 — Seat Back Only Memory: EZ Entry Lever Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Rear Head Restraints To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push downward on the head restraint. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for information on tether routing.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the bottom of the RED hood release lever, located on the left kick panel, rearward. Hood Safety Latch Location Hood Release Lever 2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. 3. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 CAUTION! To prevent possible damage, do not slam the hood to close it. Lower hood to approximately 12 inches (30 cm) and drop the hood to close. Make sure hood is fully closed for both latches. Never drive vehicle unless hood is fully closed, with both latches engaged. LIGHTS Multifunction Lever Hood Prop Rod In hot climates, the prop rod may be hot. Pick up the prop rod at the foam on the end of the prop rod.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Headlights Rotate the end of the multifunction lever upward to the first detent for headlight operation. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steering wheel. This will turn on the high beams until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Turn Signals Lane Change Assist Push the multifunction lever upward to signal a right turn or downward to signal a left turn. The corresponding indicator in the instrument cluster display will blink to indicate the operation of the turn signal. Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times. Then, the turn signal (right or left) will 3 automatically turn off.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Interior Light Timing (Center Position) The interior light switches are located in the overhead console. The interior lights can be set to three different positions (Off/Left Position, Center Position, On/Right Position). There are four different modes of operation that can be activated in this position: Using the switch on the left overhead, push the switch to the right from its center position and the lights are always on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Cargo Area Lights There is also a courtesy light located in the rear cargo area. Whenever the rear lift gate is opened, the light will turn on and then turn off when the lift gate is closed. 3 Fog Light Switch Push the switch once to turn the front fog lights on. Push the switch a second time to turn the front fog lights off.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Windshield Wiper Operation There are five different modes of operation for the front windshield wipers. The windshield wiper lever can be raised or lowered to access these modes: NOTE: The Intermittent function only has one detent, but wiper delay will vary with changes in vehicle speed. As vehicle speed increases, the delay time will decrease. Low Speed Push the lever downward to the second detent. The wipers will operate at low speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 activate automatically for three cycles after the lever is released. CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Windshield Washer Operation Push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. TILT STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 second time. The cruise control indicator light will turn off. The system should be turned off when not in use. WARNING! Leaving the Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate U.S. Speed (mph) A soft tap on the brake pedal, pushing the CANC button, or normal brake pressure while slowing the vehicle will deactivate Speed Control without erasing the set speed memory. Pushing the ON/OFF button or turning the ignition switch OFF erases the set speed in memory. • Pushing the RES (+) button once will result in a 1 mph increase in set speed. Each subsequent tap of the button results in an increase of 1 mph.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 more information. The speed decrement shown is dependant on the selected speed unit of U.S. (mph) or Metric (km/h): Using Speed Control On Hills U.S. Speed (mph) NOTE: The Speed Control system maintains speed up 3 and down hills. A slight speed change on moderate hills is normal. • Pushing the SET (-) button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR PARK ASSIST — IF EQUIPPED The Rear Park Assist system provides visual and audible indications of the distance between the rear fascia/bumper and a detected obstacle when backing up, e.g. during a parking maneuver. Refer to the “Park Assist System Usage Precautions” for the limitations of this system and recommendations. The Rear Park Assist is automatically activated when the transmission is placed into REVERSE.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 If an obstacle is detected in the left and/or right rear region, the display will show solid arcs in the left and/or right rear region and will produce an audible alert. As the vehicle moves closer to the obstacle, the display will show fewer arcs and the audible alert becomes more frequent. Rear Park Assist Audible Alerts If an obstacle is behind the vehicle when the transmission is placed into REVERSE, an audible alert is activated.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Audible And Visual Signals Supplied By The Rear Park Assist System SIGNAL Obstacle Distance MEANING An obstacle is present within the sensors’ field of view INDICATION Audible Signal (dashboard loudspeaker) • Sound pulses emitted at a rate that increases as the distance decreases. • Emits continuous tone at 12 inches (30 cm). • Adjustable volume level. (Refer to “Instrument Cluster Display” in “Understanding Your Instrument Panel” for further information).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Failure Sensor or System failures While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned off after three seconds (stopping warnings during maneuvers parallel to walls).
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Park Assist System Usage Precautions NOTE: • Ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the Rear Park Assist system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of Rear Park Assist. • Clean the Rear Park Assist sensors regularly, taking care not to scratch or damage them.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 CAUTION! • Rear Park Assist is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using Rear Park Assist in order to be able to stop in time when an obstacle is detected.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured. • Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result. position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Emergency Operation In case of electrical failure, the sunroof can be operated with the hex wrench that is located in the glove compartment. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. Insert the hex wrench and turn, moving the sunroof to the desired location.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty. Power Outlet Power is available when the ignition switch is in the ON/ RUN or START position. Insert the cigar lighter or accessory plug into the outlet for use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 WARNING! CAUTION! (Continued) To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS For the driver and front passenger, cupholders are located on the floor console between the front seats. Rear Cupholders STORAGE Glove Compartment Front Cupholders For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. The glove compartment is located on the passenger side of the instrument panel. To open the glove compartment, pull the release handle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 3 Glove Compartment Latch Rear Seat Release Buttons CARGO AREA FEATURES The rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded-down position to provide a flat load floor cargo area. When returning the seatback to its upright position, push rearward until the seatback is properly latched.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located in the center of the instrument panel, below the radio. Push this button to turn on the rear window defroster. An indicator in the instrument cluster display will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 20 minutes. To manually shut the defroster off, push the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . .111 ▫ Oil Change Message Reset . . . . . . . . . . . . . .146 䡵 TURBO BOOST GAUGE . . . . . . . . . . . . . . . . .112 ▫ Trip Computer . . . . . . . . . . . . . . . . . . . . . .147 䡵 SPORT INSTRUMENT CLUSTERS . . . . . . . . .113 ▫ Trip Button . . . . . . . . . . . . . . . . . . . . . . . . .147 䡵 SPORT TURBO INSTRUMENT CLUSTERS . . .117 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .
110 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Customer Programmable Features — Uconnect 5.0/5.0 NAV Settings . . . . . . . . . . . . . . . . .157 䡵 UCONNECT 5.0/5.0 NAV VOICE RECOGNITION QUICK TIPS . . . . . . . . . . . . . . . . . . . . . . . . .165 ▫ Introducing Uconnect. . . . . . . . . . . . . . . . . .165 ▫ Get Started . . . . . . . . . . . . . . . . . . . . . . . . .166 ▫ Basic Voice Commands . . . . . . . . . . . . . . . .166 ▫ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 ▫ Media.
UNDERSTANDING YOUR INSTRUMENT PANEL 111 INSTRUMENT PANEL FEATURES 4 1 — Side Vent 2 — Multifunction Lever – Light Control 3 — Instrument Cluster 4 — Windshield Wiper, Washer, Trip Computer 5 — Central Air Vents 6 — Radio 7 — Passenger Air Bag 8 — Glove Compartment 9 — Rear Defrost Button 10 — Hazard Button 13 14 15 16 — — — — Storage Compartment Gear Selector Sport Button Horn/Driver Air Bag 11 — Climate Controls 12 — Power Windows Control 17 — Boost Gauge
112 UNDERSTANDING YOUR INSTRUMENT PANEL TURBO BOOST GAUGE Your vehicle is equipped with a boost gauge and integrated shift light indicator located to the left of the instrument cluster. The boost gauge indicates the intake manifold pressure relative to barometric pressure. The engine management system in your vehicle intelligently regulates intake manifold pressure based on environmental (ambient) and engine operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 113 SPORT INSTRUMENT CLUSTERS 4 Sport Instrument Cluster Base
114 UNDERSTANDING YOUR INSTRUMENT PANEL Sport Instrument Cluster Sport Mode 1. Tachometer • This gauge measures engine revolutions per minute (RPM x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 2. Temperature Gauge • The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
UNDERSTANDING YOUR INSTRUMENT PANEL 115 • The digital gauge will likely indicate a higher temperature when driving in hot weather, or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range. WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
116 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Sport Base and Sport Mode Gauge Displays Depending on what options and trim level, your vehicle may be equipped with two gauge displays available with the push of the Sport Mode button. • “Sport Base” — Instant Consumption Bargraph: This bargraph shows the instant fuel consumption, the style changes according to vehicle version while minimum and maximum values change depending on selected unit.
UNDERSTANDING YOUR INSTRUMENT PANEL 117 SPORT TURBO INSTRUMENT CLUSTERS 4 Sport Turbo Instrument Cluster Base
118 UNDERSTANDING YOUR INSTRUMENT PANEL Sport Turbo Instrument Cluster Sport Mode 1. Tachometer • This gauge measures engine revolutions per minute (RPM x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 2. Temperature Gauge • The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
UNDERSTANDING YOUR INSTRUMENT PANEL 119 • The digital gauge will likely indicate a higher temperature when driving in hot weather, or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range. WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
120 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Sport Turbo Mode Depending on what options and trim level, your vehicle may be equipped with two gauge displays available with the push of the Sport Mode button. • “Sport Turbo Base” — Instant Consumption Bar Graph: This bar graph shows the instant fuel consumption, the style changes according to vehicle version while minimum and maximum values change depending on selected unit.
UNDERSTANDING YOUR INSTRUMENT PANEL 121 INSTRUMENT CLUSTER 4 Instrument Cluster 1. Tachometer • This gauge measures engine revolutions per minute (RPM x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 2. Temperature Gauge • The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
122 UNDERSTANDING YOUR INSTRUMENT PANEL • The digital gauge will likely indicate a higher temperature when driving in hot weather, or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range. WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
UNDERSTANDING YOUR INSTRUMENT PANEL 123 NOTE: Different trips may have different values even if the same driving style is maintained. Some factors that may impact the calculated index value are: • Traffic conditions • Trip duration • Temperature (engine and ambient) 6. Instrument Cluster Display • The Instrument Cluster Display features a driverinteractive display. Refer to “Instrument Cluster Display” in “Understanding Your Instrument Panel” for further information.
124 UNDERSTANDING YOUR INSTRUMENT PANEL Red Telltale Indicator Lights Air Bag Warning Light Red Telltale Light What It Means Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition is placed in the MAR (ACC/ON/RUN) position. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 125 Electric Power Steering Fail Warning Light — If Equipped Red Telltale Light What It Means Electric Power Steering Fail Warning — If Equipped This light is used to manage the electrical warning of the EPS (Electric Power Steering). Refer to “Electric Power Steering” in “Starting And Operating” for further information.
126 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 127 Battery Charge Warning Light Red Telltale Light What It Means Battery Charge Warning Light This light illuminates when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact your authorized dealer as soon as possible. This indicates a possible problem with the electrical system or a related component.
128 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Pressure Warning Light Red Telltale Light What It Means Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.
UNDERSTANDING YOUR INSTRUMENT PANEL 129 Door Open Warning Light Red Telltale Light What It Means Door Open Warning Light This indicator will illuminate when a door is ajar/open and not fully closed. • Driver’s Door Open • Passenger Door Open • Driver and Passenger Door Open Liftgate Open Warning Light Red Telltale Light What It Means Liftgate Open Warning Light This indicator will turn when the liftgate is open.
130 UNDERSTANDING YOUR INSTRUMENT PANEL Transmission Fault Warning Light Red Telltale Light What It Means Transmission Fault Warning Light This light will illuminate (together with a message in the instrument cluster display and a buzzer) to indicate a transmission fault. Contact your authorized dealer if the message remains after restarting the engine.
UNDERSTANDING YOUR INSTRUMENT PANEL 131 Yellow Telltale Indicator Lights Tire Pressure Monitoring System (TPMS) Warning Light Yellow Telltale Light What It Means Tire Pressure Monitoring System (TPMS) Warning Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
132 UNDERSTANDING YOUR INSTRUMENT PANEL Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
UNDERSTANDING YOUR INSTRUMENT PANEL 133 Electronic Stability Control (ESC) Activation/Malfunction Indicator Light Yellow Telltale Light What It Means Electronic Stability Control (ESC) Activation/Malfunction Indicator Light The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition is placed in the MAR (ACC/ON/RUN) position. It should go out with the engine running.
134 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) OFF Indicator Light Yellow Telltale Light What It Means Electronic Stability Control (ESC) OFF Indicator Light This light indicates the Electronic Stability Control (ESC) is off. For further information, refer to “Electronic Stability Control (ESC)” in “Starting And Operating.
UNDERSTANDING YOUR INSTRUMENT PANEL 135 WARNING! CAUTION! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system.
136 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. Anti-Lock Brake (ABS) Indicator Light Yellow Telltale Light What It Means Anti-Lock Brake (ABS) Indicator Light After the ignition is turned on, the Anti-Lock Brake System (ABS) light illuminates to indicate function check at vehicle startup.
UNDERSTANDING YOUR INSTRUMENT PANEL 137 Generic Warning Indicator Light Yellow Telltale Light What It Means Generic Warning Indicator Light The Generic Warning Light will illuminate if any of the following conditions occur: Oil Change Request, Engine Oil Pressure Sensor Failure, External Light Failure, Fuel Cut-Off Not Available, Parking Sensor Failure, DST System Failure.
138 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Security Indicator Light Yellow Telltale Light What It Means Vehicle Security Indicator Light This indicator will illuminate when the vehicle security alarm system has detected an attempt was made to break into the vehicle. Stop Light Failure Indicator Light Yellow Telltale Light What It Means Stop Light Failure Indicator Light This light will illuminate if one or more of the stop light bulb fails.
UNDERSTANDING YOUR INSTRUMENT PANEL 139 Low Fuel Warning Light Yellow Telltale Light What It Means Low Fuel Indicator Light When the fuel level reaches approximately 1.3 gallons (5 Liters) this light will turn on, and remain on until fuel is added.
140 UNDERSTANDING YOUR INSTRUMENT PANEL Green Telltale Indicator Lights Turn Signal Indicator Lights Green Telltale Light What It Means Turn Signal Indicator Lights The instrument cluster arrow will flash independently for the left or right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunction lever is moved down (left) or up (right).
UNDERSTANDING YOUR INSTRUMENT PANEL 141 Front Fog Indicator Light — If Equipped Green Telltale Light What It Means Front Fog Indicator Light — If Equipped This indicator will illuminate when the front fog lights are on. Cruise Control Engaged Indicator Light — If Equipped Green Telltale Light What It Means Cruise Control Engaged Indicator Light This light will turn on when the cruise control has been set to a certain speed.
142 UNDERSTANDING YOUR INSTRUMENT PANEL Blue Telltale Indicator Lights High Beam Indicator Light Blue Telltale Light What It Means High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam. Pull the lever toward you for a temporary high beam on, ⬙flash to pass⬙ scenario.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT CLUSTER DISPLAY Instrument Cluster Display And Controls Your vehicle may be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the STOP/OFF position, opening/closing of a door will activate the display for viewing, and display the total miles (kilometers) in the odometer. Your instrument cluster display is designed to display important information about your vehicle’s systems and features.
144 UNDERSTANDING YOUR INSTRUMENT PANEL The system display consists of the following: Instrument Cluster Display Control Buttons • System Status Push and release the MENU button briefly to access the instrument cluster display. Push and hold the MENU button (approximately one second) to return to the main screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 Display Menu Set-Up 4 Instrument Cluster Display Menu Screen Continued Instrument Cluster Display Menu Screen The menu comprises a series of functions arranged in a cycle. Push and release the up and down arrow buttons to access the different options and settings (setup). The setup menu can be activated by pushing the MENU button. A single push on the up or down arrow button will scroll through the setup menu options.
146 UNDERSTANDING YOUR INSTRUMENT PANEL • Trip B Data • Audio Repetition — If Equipped • Navigation Repetition — If Equipped Selecting An Option Of The Main Menu Without Submenu 1. Briefly push and release the MENU button to select the main menu option to set. 2. Push and release the up or down arrow button (by single pushes) to select the new setting. 3. Briefly push and release the MENU button to store the new setting and go back to the main menu option previously selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 RUN) position. To turn off the message temporarily, push and release the MENU button. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure. 1. Place the ignition in the MAR (ACC/ON/RUN) position. (do not start the engine.) 2. Fully push the accelerator pedal slowly, three times within 10 seconds. 3. Turn the ignition switch to the OFF position.
148 UNDERSTANDING YOUR INSTRUMENT PANEL Exit Trip “Trip B” can be used to display the figures relating to: To exit the Trip function, wait until all the values have been displayed or hold the MENU button for longer than one second. • Trip Distance B Briefly push and release the MENU button to go back to the menu screen or push and hold the MENU (approximately one second) to go back to the main screen without storing settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 • The vehicle is parked for a long time with the engine running. NOTE: The range depends on several factors: driving style, type of route (freeway, residential, mountain roads, etc.), and conditions of use of the vehicle (load, tire pressure, etc.). Trip planning must take into account the above notes. Travel Time This value shows the time elapsed since the last reset.
150 UNDERSTANDING YOUR INSTRUMENT PANEL To adjust the volume proceed as follows: Service – If Equipped 1. Briefly push and release the MENU button. Push and release the up or down arrow button, then highlight the Buzzer Volume. Push and release the MENU button to enter the Buzzer Volume MENU. 2. Push and release the up or down arrow button for setting. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 NOTE: The “Scheduled Servicing Plan” includes car maintenance at fixed intervals. This is displayed automatically, with ignition is in the MAR (ACC/ON/RUN) position, before servicing or, where provided, 30 days before servicing. Headlight Adjustment – If Equipped To set the desired headlight setting, proceed as follows: 1. Briefly push and release the MENU button. Push and release the up or down arrow button to highlight Headlight Adjustment.
152 UNDERSTANDING YOUR INSTRUMENT PANEL Trip B Data (Trip B On) 3. Briefly push and release the MENU button to go back to the menu screen, or push and hold the MENU button (approximately one second) to go back to the main screen without storing the settings. Trip B Data Submenu Settings: • On • Off • Return to MENU Audio Repetition — If Equipped Repeat Audio Information Trip B Submenu Display Through this option, it is possible to activate (On) or deactivate (Off) the Trip B (partial trip) display.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 With this function active, the instrument cluster display shows information relevant to the sound system. Audio Repetition Submenu Settings: • Radio: tuned radio station frequency, automatic tuning activation or AutoStore. • On • CD audio, CD MP3: track number. To activate (On) or to deactivate (Off) the sound system info displaying, proceed as follows: • Off • Return to MENU Navigation Repetition — If Equipped 1. Briefly push and release the MENU button.
154 UNDERSTANDING YOUR INSTRUMENT PANEL • The name of the street (1 or 2 lines) To activate (On) or to deactivate (Off) the navigation system info displaying, proceed as follows: 1. Briefly push and release the MENU button. Push and release the up or down button to highlight Navigation Repetition and push and release the MENU button. 2. Push and release the up or down button for setting. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 WARNING! (Continued) • ONLY insert media (e.g., USB, SD card, or CD) into your vehicle if it came from a trusted source. Media of unknown origin could possibly contain malicious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached. • As always, if you experience unusual vehicle behavior, take your vehicle to your nearest authorized dealer immediately.
156 UNDERSTANDING YOUR INSTRUMENT PANEL IPOD/USB/MEDIA PLAYER CONTROL — IF EQUIPPED access and change the customer programmable features. Many features can vary by vehicle. This feature allows an iPod or external USB device to be plugged into the USB or AUX port, located in the center console. Uconnect 5.0/5.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 through menus and change settings (i.e., 30, 60, 90), push the center of the control knob one or more times to select or change a setting (i.e., ON, OFF). Your Uconnect system may also have Display Off and back arrow buttons on the faceplate. Push the Display Off button on the faceplate to turn off the Uconnect screen. Push the Display Off button on the faceplate a second time to turn the screen on.
158 UNDERSTANDING YOUR INSTRUMENT PANEL Display After pressing the “Display” button on the touchscreen the following settings will be available. Setting Name Display Mode Selectable Options Auto Manual NOTE: When the “Display Mode” feature is set to “Auto” the radio touchscreen’s brightness will be adjusted with all other Instrument Panel displays and lights when they are adjusted using the instrument cluster display buttons on the right-hand side of the instrument cluster display.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 After pressing “Custom” on the touchscreen, you may select from one of the below menu items: Setting Name Fuel Consumption Temperature Pressure Selectable Options MPG (UK) L/100 km MPG (US) °C psi km/L °F kPa 4 Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Voice Response Length Show Command List Selectable Options Brief Always Long With Help Never Clock & Date After pressing the “Clock & Da
160 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Show Time Status Set Date Selectable Options On Off Set Date NOTE: Press the corresponding arrows above and below the current date to adjust. Sync Time — If Equipped On Off NOTE: When in the “Sync Time” display, you may sync the time with GPS.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 Doors & Locks After pressing the “Doors & Locks” button on the touchscreen, the following setting will be available: Setting Name Auto Door Locks Selectable Options On Off NOTE: When the “Auto Door Locks” feature is selected, all doors will lock automatically when the vehicle reaches a speed of 12 mph (20 km/h).
162 UNDERSTANDING YOUR INSTRUMENT PANEL Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Equalizer Selectable Options + – NOTE: • When in the “Equalizer” display, you may adjust the Bass, Mid and Treble settings. • Bass/Mid/Treble allow you to simply slide your finger up or down to change the setting as well as press directly on the desired setting. Balance/Fade When in the “Balance/ Fade” display, you may adjust the Balance settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touchscreen, the following settings will be available: Setting Name Paired Phones Selectable Options List of Paired Phones 4 NOTE: The “Paired Phones” feature shows which phones are paired to the Phone/Bluetooth system. For further information, refer to the Uconnect Owner’s Manual Supplement.
164 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Subscription Information Selectable Options Subscription Info NOTE: • New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe. • Write down the SIRIUS ID numbers for your receiver.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 Clear Personal Data After pressing the “Clear Personal Data Settings” button on the touchscreen, the following settings will be available: Setting Name Clear Personal Data Selectable Options Yes 4 No NOTE: When this feature is selected, it will remove personal data including Bluetooth devices and presets.
166 UNDERSTANDING YOUR INSTRUMENT PANEL Get Started 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions. All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 • Cancel to stop a current voice session Push the VR button • Help to hear a list of suggested Voice Commands • Tune to ninety-five-point-five FM • Repeat to listen to the system prompts again • Tune to Satellite Channel Hits 1 Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touchscreen. TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button 4 and say Help.
168 UNDERSTANDING YOUR INSTRUMENT PANEL Media Uconnect offers connections via USB, Bluetooth and Auxiliary ports (If Equipped). Voice operation is only available for connected USB and iPod devices. . After the beep, say one of the Push the VR button following commands and follow the prompts to switch your media source or choose an artist.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. No. Start without I’ll be late. me. Okay. Where are I will be minutes late. Call me. Are you there yet? I’ll call you I need direcSee you in later. tions. of minutes. I’m on my way. Can’t talk right now. I’m lost. Thanks. TIP: Your mobile phone must have the full implementation of the Message Access Profile (MAP) to take advantage of this feature.
170 UNDERSTANDING YOUR INSTRUMENT PANEL For Uconnect system support, call 1-877-855-8400 (24 hours a day 7 days a week) or visit DriveUconnect.com. STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Pushing the center button will make the radio switch between the various modes available (AM/FM/SAT/ AUX/Media Player, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 This condition is not harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the antenna, it is recommended that the radio volume be turned down or off during mobile phone operation.
172 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Climate Control Descriptions Icon Description A/C Button Push the A/C button to engage the Air Conditioning (A/C). A LED will illuminate when the A/C system is engaged. Recirculation Setting When this setting is on, the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 Icon Description Blower Control There are seven blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. NOTE: Depending on the configuration, your vehicle may be equipped with four blower speeds. Modes Control: Turn the knob clockwise or counterclockwise to change the airflow distribution mode.
174 UNDERSTANDING YOUR INSTRUMENT PANEL Icon Floor Mode Description Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 Automatic Temperature Control Overview 4 Automatic Temperature Controls Control Descriptions Icon Description A/C Button Push and release to change the current setting, the indicator illuminates when A/C is ON. Performing this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off.
176 UNDERSTANDING YOUR INSTRUMENT PANEL Icon Description Recirculation Button Push and release this button to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present. NOTE: • Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 Icon Description Blower Control Up And Down Buttons Provides the passengers with blower control. Push the UP button to increase blower speed. Push the DOWN button to decrease blower speed. 4 Modes Control: Push the button in the center of the knob to change the airflow distribution mode. The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.
178 UNDERSTANDING YOUR INSTRUMENT PANEL Icon Bi-Level Mode Mix Mode Description Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. To access this mode, press both the Panel and Floor Mode buttons NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
180 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (button on the touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield. On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation. Recirculation will be disabled automatically if this mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 NOTE: The system will not automatically sense the presence of fog, mist or ice on the windshield. DEFROST mode must be manually selected to clear the windshield and side glass. Operating Tips NOTE: Refer to the chart at the end of this section for suggested control settings for various weather conditions.
182 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Vehicle windows tend to fog on the inside in mild, rainy and/or humid weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur. Outside Air Intake Make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 Operating Tips Chart 4
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . .188 ▫ Manual Transmission — If Equipped . . . . . .188 ▫ Automatic Transmission — If Equipped . . . .188 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . .188 ▫ Cold Weather Operation . . . . . . . . . . . . . . .188 ▫ Extended Park Starting. . . . . . . . . . . . . . . . .189 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . .189 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . .
186 STARTING AND OPERATING 䡵 POWER STEERING . . . . . . . . . . . . . . . . . . . .202 ▫ Tire Terminology And Definitions . . . . . . . . .217 䡵 PARKING BRAKE . . . . . . . . . . . . . . . . . . . . .203 ▫ Tire Loading And Tire Pressure . . . . . . . . . .218 䡵 SPORT MODE . . . . . . . . . . . . . . . . . . . . . . . .205 䡵 TIRES — GENERAL INFORMATION . . . . . . .223 ▫ Manual Transmission — If Equipped . . . . . . .205 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 187 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . .234 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . .234 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . .234 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . .234 䡵 TIRE PRESSURE MONITORING SYSTEM (TPMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235 ▫ TPM System With Comfort Cluster . . . . . . . .237 ▫ TPM System With (TFT) Tire Pressure Display Screen . . . .
188 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.
STARTING AND OPERATING 189 (–30° C) and the oil temperature sensor reading indicates an engine block heater has not been used. An externally-powered electric engine block heater is available as optional equipment from your authorized dealer or may be standard equipment in some markets.
190 STARTING AND OPERATING CAUTION! • Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. • To prevent damage to the starter, do not continuously crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING 191 Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears.
192 STARTING AND OPERATING Downshifting AUTOMATIC TRANSMISSION — IF EQUIPPED Proper downshifting will improve fuel economy and prolong engine life. CAUTION! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released.
STARTING AND OPERATING 193 WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector. • Do not leave the ignition key in or near the vehicle (or in a location accessible to children).
194 STARTING AND OPERATING Six-Speed Automatic Transmission The transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the gear selector out of PARK (Refer to “Brake/Transmission Shift Interlock System” in this section). To drive, move the gear selector from PARK or NEUTRAL to the DRIVE position. The electronically-controlled transmission provides a precise shift schedule.
STARTING AND OPERATING 195 DRIVE position) will manually select the transmission gear, and will display the current gear in the instrument cluster as 1, 2, 3, etc. When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake. NOTE: If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward) it is probably in the AutoStick (+/-) position (beside the DRIVE position).
196 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Your vehicle could move and injure you and others if it is not in PARK. Check by trying to move the gear selector out of PARK with the brake pedal released. Make sure the transmission is in PARK before exiting the vehicle. • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.
STARTING AND OPERATING 197 The following indicators should be used to ensure that you have engaged the transmission into the PARK position: • When shifting into PARK, push the lock button on the gear selector and firmly move the gear selector all the way forward until it stops and is fully seated. • Look at the transmission gear position display and verify that it indicates the PARK position (P). • With brake pedal released, verify that the gear selector will not move out of PARK.
198 STARTING AND OPERATING When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, or traveling into strong head winds), use the AutoStick shift control (refer to AutoStick in this section for further information) to select a lower gear. Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat buildup.
STARTING AND OPERATING 199 NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required. AUTOSTICK AutoStick is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle.
200 STARTING AND OPERATING • The system will ignore shift commands that would cause engine lugging or overspeed. An audible beep will sound if an inappropriate gear is requested. DRIVING ON SLIPPERY SURFACES • Avoid using speed control when AutoStick is engaged because the transmission will not shift automatically. Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the driving wheels to pull erratically to the right or left.
STARTING AND OPERATING 201 • Slow down during rainstorms or when the roads are slushy. • Slow down if the road has standing water or puddles. • Replace the tires when tread wear indicators first become visible. • Keep tires properly inflated. • Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop.
202 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • Failure to follow these warnings may result in injuries that are serious or fatal to you, your passengers, and others around you. after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage. Such damage is not covered by the New Vehicle Limited Warranty.
STARTING AND OPERATING 203 WARNING! Continued operation with reduced or no power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. If the Steering icon is flashing, it indicates that the vehicle needs to be taken to an authorized dealer for service. It is likely the vehicle has lost power steering assistance.
204 STARTING AND OPERATING WARNING! Parking Brake When the parking brake is applied with the ignition switch in the MAR (ACC/ON/RUN) position, the Brake Warning Light in the instrument cluster will illuminate. When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle.
STARTING AND OPERATING 205 CAUTION! If the Brake Warning Light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. SPORT MODE 5 Manual Transmission — If Equipped In Sport mode, the engine is more responsive to the throttle pedal, and provides more maximum torque by increasing turbo boost pressure. Steering feedback is improved, and steering effort is slightly higher.
206 STARTING AND OPERATING 1. To activate the Sport mode, push the SPORT button. during application, greater pedal force required to slow or stop, and potential activation of the “Brake System Warning Light”. In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off), the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. ELECTRONIC BRAKE CONTROL SYSTEM 2.
STARTING AND OPERATING 207 to modulate hydraulic pressure, to prevent wheel lock-up and to help avoid skidding on slippery surfaces. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. The ABS includes an amber ABS Warning Light. When the light is illuminated, the ABS is not functioning. The system reverts to standard non-anti-lock brakes.
208 STARTING AND OPERATING Brake Assist System (BAS) WARNING! (Continued) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS). Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING 209 Hill Start Assist (HSA) The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short period of time after the driver takes his foot off the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill.
210 STARTING AND OPERATING the desired path. ESC uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position.
STARTING AND OPERATING 211 WARNING! (Continued) slippery surfaces, or hydroplaning. ESC also cannot prevent collisions resulting from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESC equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
212 STARTING AND OPERATING WARNING! WARNING! When in “Partial Off” mode, the TCS functionality of ESC (except for the limited slip feature described in the TCS section) has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the engine power reduction of TCS is disabled, and the enhanced vehicle stability offered by the ESC system is reduced. In the ESC “Full Off” mode, the engine torque reduction and stability features are cancelled.
STARTING AND OPERATING 213 The ESC Activation/Malfunction Indicator Light (located in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. The ESC Activation/Malfunction Indicator Light also flashes when TCS is active. If the ESC Activation/ Malfunction Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions.
214 STARTING AND OPERATING NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H.
STARTING AND OPERATING 215 EXAMPLE: 65, 85, 80 = Aspect ratio in percent (%) – Ratio of section height to section width of tire, or 10.
216 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 217 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
218 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle. Example Tire Placard Location (B-Pillar) WARNING! • Overloading of your tires is dangerous.
STARTING AND OPERATING 219 WARNING! (Continued) • Improperly inflated tires are dangerous and can cause collisions. Under-inflation increases tire flexing and can result in over-heating and tire failure. Over-inflation reduces a tire’s ability to cushion shock. Objects on the road and chuck holes can cause damage that results in tire failure. Unequal tire pressures can cause steering problems. You could lose control of your vehicle.
220 STARTING AND OPERATING Loading Steps For Determining Correct Load Limit— The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading” in “Starting And Operating”, or the Tire Information Supplement, located in your Owner’s Information kit.
STARTING AND OPERATING 221 Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Metric Example For Load Limit For example, if “XXX” amount equals 635 kg, and there will be five 68 kg passengers in your vehicle, the amount of available cargo and luggage load capacity is 295 kg (635-340 (5x68) = 295 kg) as shown in step 4. NOTE: • If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
222 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
STARTING AND OPERATING 223 TIRES — GENERAL INFORMATION WARNING! (Continued) Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Four primary areas are affected by improper tire pressure: • Safety and Vehicle Stability • Economy • Tread Wear • Ride Comfort Safety • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. • Unequal tire pressures can cause steering problems.
224 STARTING AND OPERATING Tread Wear Improper cold tire inflation pressures can cause abnormal wear patterns and reduced tread life, resulting in the need for earlier tire replacement. Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortable ride. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or rear edge of the driver’s side door.
STARTING AND OPERATING 225 inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. WARNING! (Continued) serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
226 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and additional information. Damaged Run Flat tires, or Run Flat tires that have experienced a loss of pressure should be replaced immediately with another Run Flat tire of identical size and service description (Load Index and Speed Symbol). Tire Types All Season Tires — If Equipped All season tires provide traction for all seasons (Spring, Summer, Fall and Winter). Traction levels may vary between different all season tires.
STARTING AND OPERATING 227 Snow Tires Run Flat Tires — If Equipped Some areas of the country require the use of snow tires during the Winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the Run Flat mode. A Run Flat mode occurs when the tire inflation pressure is of/or below 14 psi (96 kPa).
228 STARTING AND OPERATING CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact or limited use temporary spare installed. Damage to the vehicle may result. Spare Tire Matching Original Equipped Tire And Wheel — If Equipped Your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle.
STARTING AND OPERATING 229 Collapsible Spare Tire — If Equipped The collapsible spare is for temporary emergency use only. You can identify if your vehicle is equipped with a collapsible spare by looking at the spare tire description on the Tire and Loading Information Placard located on the driver’s side door opening or on the sidewall of the tire. Collapsible spare tire description example: 165/80-17 101P.
230 STARTING AND OPERATING Limited Use Spare — If Equipped Tire Spinning The limited use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited use spare wheel. This label contains the driving limitations for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
STARTING AND OPERATING 231 • Driving style. • Tire pressure – Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life, resulting in the need for earlier tire replacement. • Distance driven. Tire Tread 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm).
232 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed. Refer to the paragraph on “Tread Wear Indicator” in this section.
STARTING AND OPERATING 233 CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. TIRE CHAINS (TRACTION DEVICES) Due to limited clearance, tire chains or traction devices are not recommended. CAUTION! type tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “Maintenance Schedule” for the proper maintenance intervals.
234 STARTING AND OPERATING DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger vehicle tires must conform to Federal safety requirements in addition to these grades.
STARTING AND OPERATING 235 tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
236 STARTING AND OPERATING may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (159 kPa).
STARTING AND OPERATING 237 • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
238 STARTING AND OPERATING TPMS Warnings The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and remain on solid when a system fault is detected, an audible chime will be activated and the “Service Tire Pressure Monitoring System” text message will display. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The Tire Pressure Monitoring Telltale Light will turn off when the fault condition no longer exists.
STARTING AND OPERATING 239 the Tire Pressure Monitoring Telltale Light will turn OFF, as long as no tire pressure is below the lowpressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. sound when tire pressure is low in one or more of the four active road tires.
240 STARTING AND OPERATING need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. TPMS Warning When a system fault is detected, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid. The system fault will sound a chime and also display a “Service Tire Pressure Monitoring System” message in the instrument cluster for approximately 5 seconds.
STARTING AND OPERATING 241 NOTE: • The TPMS will not monitor the pressure in a replacement tire installed without a tire pressure sensor. • If you install a replacement tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition switch cycle, the “Tire Pressure Monitoring Telltale Light” will remain on and a chime will sound.
242 STARTING AND OPERATING FUEL REQUIREMENTS This engine is designed to meet all emission regulations and provide satisfactory fuel economy and performance when using high-quality unleaded “regular” gasoline with a minimum octane rating of 87. For optimum performance and fuel economy the use of 91 octane or higher is recommended. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required.
STARTING AND OPERATING 243 CAUTION! (Continued) Light” to illuminate. Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (E-15). Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may void or not be covered under New Vehicle Limited Warranty.
244 STARTING AND OPERATING Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion, and stability additives are recommended. Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance. Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.
STARTING AND OPERATING 245 NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! WARNING! (Continued) • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. ADDING FUEL Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases.
246 STARTING AND OPERATING CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel filler cap. A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
STARTING AND OPERATING 247 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Flat Tow Wheels OFF the Ground NONE Dolly Tow Front Rear ALL On Trailer NOTE: When towing your vehicle, always follow applicable state and provincial laws. Contact state and provincial Highway Safety offices for additional details. This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . .250 ▫ Preparations For Jump-Start . . . . . . . . . . . . .261 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . .250 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . .262 䡵 TIRE SERVICE KIT — IF EQUIPPED . . . . . . . .251 䡵 FREEING A STUCK VEHICLE . . . . . . . . . . . .263 ▫ Tire Service Kit Storage . . . . . . . . . . . . . . . .251 䡵 GEAR SELECTOR OVERRIDE . . . . . . . . . . . .
250 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS • On the highways — slow down. The Hazard Warning flasher switch is located on the instrument panel below the radio. • In city traffic — while stopped, place the transmission in NEUTRAL, but do not increase engine idle speed. Push the switch to turn on the Hazard Warning flashers. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.
WHAT TO DO IN EMERGENCIES 251 CAUTION! Tire Service Kit Components And Operation Driving with a hot cooling system could damage your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off immediately and call for service.
252 WHAT TO DO IN EMERGENCIES Using The Mode Select Knob And Hoses Tire Service Kit Usage Precautions Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. • Replace the Tire Service Kit Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed at the lower right hand corner on the bottle label) to assure optimum operation of the system. Refer to “Sealing A Tire With Tire Service Kit” section (F) “Sealant Bottle And Hose Replacement”.
WHAT TO DO IN EMERGENCIES 253 • When the Tire Service Kit sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the Tire Service Kit. • You can use the Tire Service Kit air pump to inflate bicycle tires.
254 WHAT TO DO IN EMERGENCIES WARNING! (Continued) warnings can result in injuries that are serious or fatal to you, your passengers, and others around you. • Take care not to allow the contents of Tire Service Kit to come in contact with hair, eyes, or clothing. Tire Service Kit sealant is harmful if inhaled, swallowed, or absorbed through the skin. It causes skin, eye, and respiratory irritation. Flush immediately with plenty of water if there is any contact with eyes or skin.
WHAT TO DO IN EMERGENCIES 255 4. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the valve stem. 5. Uncoil the Power Plug (8) and insert the plug into the vehicle’s 12 Volt power outlet. NOTE: Do not remove foreign objects (e.g., screws or nails) from the tire. (C) Injecting Tire Service Kit Sealant Into The Deflated Tire: • Always start the engine before turning on the Tire Service Kit.
256 WHAT TO DO IN EMERGENCIES If the sealant (white fluid) does flow through the Sealant Hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hose (typically takes 30 - 70 seconds). As the sealant flows through the Sealant Hose (6), the Pressure Gauge (3) can read as high as 70 psi (4.8 Bar). The Pressure Gauge (3) will decrease quickly from approximately 70 psi (4.8 Bar) to the actual tire pressure when the Sealant Bottle (1) is empty. 2.
WHAT TO DO IN EMERGENCIES 257 CAUTION! (Continued) contacting your skin, clothing, and the vehicle’s interior. It can also result in sealant contacting internal Tire Service Kit components which may cause permanent damage to the kit. (D) Drive Vehicle: Immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the Tire Service Kit Sealant within the tire. Do not exceed 55 mph (90 km/h).
258 WHAT TO DO IN EMERGENCIES 2. Disconnect the Tire Service Kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 Volt outlet. 3. Push the Sealant Bottle release button. The Sealant Bottle (1) will pop up. Remove the bottle and dispose of it accordingly. 3. Place the Tire Service Kit in its proper storage area in the vehicle. 4. Clean any remaining sealant from the Tire Service Kit housing. 4.
WHAT TO DO IN EMERGENCIES 259 Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Torque Specifications Lug Nut/Bolt Torque **Lug Nut/ Bolt Size 66 Ft-Lbs (90 N·m) Steel Wheels Only 74 Ft-Lbs (100 N·m) Aluminum Wheels Only M12 x 1.25 Lug Nut/ Bolt Socket Size 17 mm **Use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.
260 WHAT TO DO IN EMERGENCIES Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. JUMP-STARTING PROCEDURE If your vehicle has a discharged battery, it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.
WHAT TO DO IN EMERGENCIES 261 Preparations For Jump-Start The battery in your vehicle is located on the left side of the engine compartment. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured.
262 WHAT TO DO IN EMERGENCIES 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion.
WHAT TO DO IN EMERGENCIES 263 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then turn the key to RUN position on the vehicle with the discharged battery. 6. Once the vehicle is started, remove the jumper cables in the reverse sequence: Disconnecting The Jumper Cables 1. Disconnect the negative (-) jumper cable from the engine ground (-) of the vehicle with the discharged battery. 2.
264 WHAT TO DO IN EMERGENCIES NOTE: Push the ⬙ESC Off⬙ switch, to place the Electronic Stability Control (ESC) system in ⬙Partial Off⬙ mode, before rocking the vehicle. Refer to “Electronic Brake Control” in “Starting And Operating” for further information. Once the vehicle has been freed, push the ⬙ESC Off⬙ switch again to restore ⬙ESC On⬙ mode. WARNING! CAUTION! (Continued) • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.
WHAT TO DO IN EMERGENCIES 265 4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the gear selector to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. 8. Reinstall the gear selector override access cover. TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled 6 vehicle using a commercial towing service.
266 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws regarding vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
WHAT TO DO IN EMERGENCIES 267 CAUTION! Towing this vehicle in violation of the above requirements can cause severe engine and/or transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 1.4L TURBO . . .271 ▫ Windshield Wiper Blades . . . . . . . . . . . . . .283 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II .272 ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . .285 ▫ Onboard Diagnostic System (OBD II) Cybersecurity . . . . . . . . . . . . . . . . . . . . . . .272 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . .285 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . .
270 MAINTAINING YOUR VEHICLE 䡵 BULB REPLACEMENT . . . . . . . . . . . . . . . . .308 ▫ Interior Bulbs . . . . . . . . . . . . . . . . . . . . . . .308 ▫ Exterior Bulbs . . . . . . . . . . . . . . . . . . . . . . .308 䡵 FLUID CAPACITIES . . . . . . . . . . . . . . . . . . .311 䡵 FLUIDS, LUBRICANTS, AND GENUINE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .312 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . .312 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 271 ENGINE COMPARTMENT — 1.
272 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 273 WARNING! (Continued) • If unauthorized equipment is connected to the OBD II connection port, such as a driver-behavior tracking device, it may: • Be possible that vehicle systems, including safety related systems, could be impaired or a loss of vehicle control could occur that may result in an accident involving serious injury or death. • Access, or allow others to access, information stored in your vehicle systems, including personal information.
274 MAINTAINING YOUR VEHICLE 3. Approximately 15 seconds later, one of two things will happen: • The MIL will flash for about 10 seconds and then return to being fully illuminated until you cycle the ignition OFF or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. • The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off position or start the engine.
MAINTAINING YOUR VEHICLE 275 WARNING! CAUTION! (Continued) You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized dealer or qualified repair center.
276 MAINTAINING YOUR VEHICLE check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. Checking the oil while the vehicle is on level ground, and approximately five minutes after a fully warmed engine is shut off, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick. The safe range is indicated by a crosshatch zone. Adding 1 quart (0.
MAINTAINING YOUR VEHICLE 277 Lubricants which do not have both the engine oil certification mark and the correct SAE viscosity grade number should not be used. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information. Materials Added To Engine Oil Do not add any supplemental materials, other than leak detection dyes, to the engine oil.
278 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE 279 CAUTION! (Continued) WARNING! the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. • If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage.
280 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R134a — If Equipped be performed by authorized dealer or other service facilities using recovery and recycling equipment. R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE 281 The A/C air filter is located in the fresh air inlet on the lower right of center console. Perform the following procedure to replace the filter: 2. Pull the console closeout cover rearward to disengage the front retaining tab and remove the cover. 1. Remove the Torx screw that secures the passenger side console closeout cover.
282 MAINTAINING YOUR VEHICLE 3. Remove the two 5.5 mm screws (1 and 2) that secure the particulate air filter cover to the HVAC housing. A/C Air Filter Air Filter Cover Screw Locations 4. Remove the A/C air filter by pulling it straight out of the housing. Take note of the air filter position indicators. 5. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal.
MAINTAINING YOUR VEHICLE 283 Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as Mopar Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
284 MAINTAINING YOUR VEHICLE Rear Wiper Blade Removal/Installation 1. Lift the pivot cap on the rear wiper arm upward, this will allow the rear wiper blade to be raised off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. Removing The Wiper Blade Lifting The Pivot Cap 1 — Wiper Arm 2 — Pivot Cap NOTE: The rear wiper arm cannot be raised fully upward unless the pivot cap is raised first. 2.
MAINTAINING YOUR VEHICLE 285 5. Lower the wiper blade and snap the pivot cap into place. Adding Washer Fluid The windshield washer fluid reservoir is located in the engine compartment, and the fluid level should be checked at regular intervals. Fill the reservoir with windshield washer solvent (not engine coolant/ antifreeze). Refer to “Engine Compartment” in this section for further information. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you.
286 MAINTAINING YOUR VEHICLE CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 287 WARNING! (Continued) • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never open a cooling system pressure cap when the radiator or coolant bottle is hot. • Keep hands, tools, clothing, and jewelry away from the radiator cooling fan when the hood is raised.
288 MAINTAINING YOUR VEHICLE Selection Of Coolant CAUTION! (Continued) Refer to “Fluids, Lubricants, And Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
MAINTAINING YOUR VEHICLE 289 Please review these recommendations for using Organic Additive Technology (OAT) engine coolant (antifreeze) that meets the requirements of FCA Material Standard MS.90032. When adding engine coolant (antifreeze): NOTE: • We recommend using Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) that meets the requirements of FCA Material Standard MS.90032. • Some vehicles require special tools to add coolant properly.
290 MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
MAINTAINING YOUR VEHICLE 291 Points To Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator.
292 MAINTAINING YOUR VEHICLE Brake Master Cylinder NOTE: If your vehicle is equipped with a manual transmission, the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transmission clutch release system should not require fluid replacement during the life of the vehicle.
MAINTAINING YOUR VEHICLE 293 WARNING! (Continued) CAUTION! original factory installed hydraulic master cylinder reservoir. • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point.
294 MAINTAINING YOUR VEHICLE Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless lubricant has become contaminated with water. NOTE: If contaminated with water, the fluid should be changed immediately.
MAINTAINING YOUR VEHICLE 295 CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. Fluid Level Check The fluid level is preset at the factory and does not require adjustment under normal operating conditions. Routine fluid level checks are not required, therefore the transmission has no dipstick.
296 MAINTAINING YOUR VEHICLE What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.
MAINTAINING YOUR VEHICLE 297 • If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. or control dust on dirt roads. Use a soft cloth or sponge and mild soap to wipe away promptly. Do not use harsh chemicals or a stiff brush. They can damage the wheel’s protective coating that helps keep them from corroding and tarnishing.
298 MAINTAINING YOUR VEHICLE When cleaning extremely dirty wheels including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels. Mopar Wheel Treatment, Mopar Chrome Cleaner, or their equivalent is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels. Do not use any products on Dark Vapor or Black Satin Chrome Wheels.
MAINTAINING YOUR VEHICLE 299 • For grease stains, apply Mopar Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. leather conditioner is not required to maintain the original condition. • Do not use any harsh solvents or any other form of protectants on Stain Repel products. WARNING! Interior Care Use Mopar Total Clean to clean fabric upholstery and carpeting. Use Mopar Total Clean to clean vinyl upholstery.
300 MAINTAINING YOUR VEHICLE Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
MAINTAINING YOUR VEHICLE 301 1. Clean with a wet soft cloth. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp cloth. 2. Dry with a soft cloth. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
302 MAINTAINING YOUR VEHICLE Interior Fuses WARNING! (Continued) • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • If the replaced fuse blows again, contact an authorized dealer. • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer.
MAINTAINING YOUR VEHICLE 303 Mini Fuse Description 4 5 Vehicle Fuse Number F38 F36 20 Amp Yellow 10 Amp Red 6 7 8 9 10 F43 F48 F13 F50 F51 20 Amp Yellow 20 Amp Yellow 7.5 Amp Brown 7.
304 MAINTAINING YOUR VEHICLE Underhood Fuses The Front Distribution Unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The ID number of the electrical component corresponding to each fuse can be found on the back of the cover.
MAINTAINING YOUR VEHICLE 305 Cavity F06 F06 F07 F08 F09 F10 F11 F11 F14 F15 F16 F17 F17 F18 F18 F19 F20 F21 F22 F23 Maxi Fuse 20 Amp Yellow 30 Amp Green 40 Amp Orange 40 Amp Orange – – – – – – – – – – – – – – – – Mini Fuse – – – – 10 Amp Red 10 Amp Red 15 Amp Blue 10 Amp Red 5 Amp Tan 15 Amp Blue 7.5 Amp Brown 25 Amp Clear 15 Amp Blue 15 Amp Blue 5 Amp Tan 7.
306 MAINTAINING YOUR VEHICLE Cavity F24 F30 F82 F83 F84 F85 F87 F90 Maxi Fuse – – 30 Amp Green 20 Amp Yellow – 30 Amp Green – – Mini Fuse 7.5 Amp Brown 15 Amp Blue – – 10 Amp Red – 5 Amp Tan 5 Amp Tan VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e.
MAINTAINING YOUR VEHICLE 307 REPLACEMENT BULBS Interior Bulbs Overhead Lamp Courtesy Lamp Rear Cargo Lamp Bulb Number C5W W5W W5W Exterior Bulbs Front Low and High Beam Headlamp Front Parking/Daytime Running Lamps Front Fog Lamps Front Side Marker Lamps Front Turn Signal Lamps Side Direction Lamps Rear Turn Signal Lamps Rear Side Marker Lamps Rear Tail and Stop Lamps Rear Backup Lamps Center High Mounted Stop Lamp License Plate Lamps Bulb Number HIR2LL W21/5W H11LL W3W WY21W WY5W PY21W W3W P21/5W W16W W
308 MAINTAINING YOUR VEHICLE Bulb Number NOTE: Numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual. BULB REPLACEMENT Headlamps Low Beam And High Beam Interior Bulbs 1. Remove the plastic cap from the back of the headlamp housing. Rear Cargo Lamp 1. Using a suitable tool open the light box. 2. Pull the bulb out. 3.
MAINTAINING YOUR VEHICLE 309 7. Reinstall the plastic cap. Front Fog Lamps To replace the front fog lights, see your authorized dealer. Front/Rear Side Marker Lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. Wheel Housing Access Door 3. Remove the plastic cap from the back of the lamp housing. 2. Rotate the bulb socket counterclockwise, and remove the bulb and socket assembly from the housing. 7 3. Pull the bulb from the socket and insert the replacement bulb. 4.
310 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Backup And Turn Signal Lamps 1. Open the liftgate. 2. Remove the two screws and remove the tail lamp assembly. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as required and reinstall lamp. Center High Mounted Stop Lamp (CHMSL) 1. Remove the two guard caps and the two fastening screws. 2. Remove the center high mounted stop lamp assembly. 3. Disconnect the electric connector. 4. Press the retaining device and open the bulb holder. 5.
MAINTAINING YOUR VEHICLE 311 FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 1.4 Liter Turbo Engine Cooling System 1.4 Liter Turbo Engine (Mopar Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) — with Manual Transmission 1.4 Liter Turbo Engine (Mopar Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) — with Automatic Transmission U.S. 10.5 Gallons Metric 40 Liters 4 Quarts 3.8 Liters 4.6 Quarts 4.4 Liters 5.8 Quarts 5.
312 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Fluid, Lubricant, or Genuine Part We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of FCA Material Standard MS-90032. We recommend you use API Certified SAE 5W-40 Full Synthetic Engine Oil, meeting the requirements of FCA Material Standard MS-12991. Refer to your engine oil filler cap for correct SAE grade.
MAINTAINING YOUR VEHICLE 313 CAUTION! (Continued) CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . .316 ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . .
316 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle.
MAINTENANCE SCHEDULES 317 Maintenance Chart At Every Oil Change Interval As Indicated By Oil Change Indicator System: Inspect battery and clean and tighten terminals as required. Inspect brake pads, rotors, and park brake. Inspect engine cooling system protection and hoses. Inspect exhaust system. Inspect engine air cleaner if using in dusty or offroad conditions. Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for required maintenance.
Inspect parking brake function, adjust as necessary. Additional Maintenance Replace cabin/air conditioning filter. Clean and lube sun roof tracks. Replace engine air filter. Replace the spark plugs. ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Inspect and replace PCV valve if necessary. Replace accessory drive belt and tensioner. Replace the timing belt.
MAINTENANCE SCHEDULES 319 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . .322 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . .323 ▫ Prepare For The Appointment. . . . . . . . . . . .322 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . .323 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . .322 䡵 WARRANTY INFORMATION . . . . . . . . . . . .
322 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you are having warranty work done, be sure to bring the right papers with you, as well as your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history, as this can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 323 Any communication to the manufacturer’s customer center should include the following information: • Owner’s name and address • Owner’s telephone number (home and office) center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1-800-380-CHRY.
324 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 325 remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer or FCA US LLC. To contact NHTSA, you may call the Vehicle Safety Hotline toll free at 1-888-327-4236 (TTY: 1-800-4249153); or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE., West Building, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
326 IF YOU NEED CONSUMER ASSISTANCE Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA US LLC vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. • Call toll free at: • 1-800-890-4038 (U.S.) • 1-800-387-1143 (Canada) Or • Visit us on the Worldwide Web at: • www.techauthority.
INDEX 10
328 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . .288 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . .245 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . .285 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . .244 Air Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Advance Front Air Bag . . . . . . . . . . . . . . . . . . .36 Air Bag Operation . . . . . . . . . . . . . . . . . . . . . .38 Driver Knee Air Bag . . . . . . .
INDEX 329 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . .127, 278 Charging System Light . . . . . . . . . . . . . . . . . .127 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . .260 Keyless Key Fob Replacement . . . . . . . . . . . . . .17 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Body Mechanism Lubrication . . . . . . . . . . . . . . . .283 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . .218 Brake Assist System . . . . . . . .
330 INDEX Clutch Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . .292 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . .228 Connector UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Universal Consumer Interface (UCI) . . . . . . . . .156 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . .323 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . . . . . .311 Cooling System. . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 331 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265 Emission Control System Maintenance . . . . . . . . .273 Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . .277 Break-In Recommendations . . . . . . . . . . . . . . . .63 Checking Oil Level . . . . . . . . . . . . . . . . . . . . .275 Compartment . . . . . . . . . . . . . . . . . . . . . . . . .271 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286 Exhaust Gas Caution . . . . . . . . . . . . .
332 INDEX Gasoline . . . . . Light . . . . . . . . Materials Added Methanol . . . . . Octane Rating . . Requirements . . Specifications . . Tank Capacity . . Fueling . . . . . . . . Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 333 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . .260 Key Fob Disarm The Alarm . . . . . . . . Key Fob Battery Service (Remote Key-In Reminder . . . . . . . . . . . Key, Replacement . . . . . . . . . . . Keys . . . . . . . . . . . . . . . . . . . . Key, Sentry (Immobilizer) . . . . . ........... Keyless Entry) ........... ........... ........... ........... . . . . . . . . . . . . .14 .17 .13 .14 .11 .13 Lane Change Assist . . . . . . . . . . . . . . . . . . . . . . .
334 INDEX Malfunction Indicator Light (Check Engine) . .134, 273 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . .325 Manual Transmission . . . . . . . . . . . . . . . . . .190, 293 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . .293 Frequency Of Fluid Change . . . . . . . . . . . . . . .294 Lubricant Selection . . . . . . . . . . . . . . . . . .293, 313 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . .292 Methanol . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 335 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Pregnant Women And Seat Belts . . . . . . . . . . . . . .31 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . .225 Radio Frequency General Information . . . . . . . . . . . . . . . . . . . . .19 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . .170 Rear Liftgate (Sedan) . . . . . . . . . . . . . . . . . . . . . .
336 INDEX Front Seat . . . . . . . . . . . . . . . . . . . . . . .25, 26, 28 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Operating Instructions . . . . . . . . . . . . . . . . . . .28 Pregnant Women . . . . . . . . . . . . . . . . . . . . . . .31 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . .32 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Untwisting Procedure . . . . . .
INDEX 337 Temperature Control, Automatic (ATC) . . . . . . . . .180 Tilt Steering Column. . . . . . . . . . . . . . . . . . . . . . .92 Tire And Loading Information Placard . . . . . .218, 219 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . .213 Tires . . . . . . . . . . . . . . . . . . . . .67, 223, 227, 228, 234 Aging (Life Of Tires) . . . . . . . . . . . . . . . . . . . .231 Air Pressure . . . . . . . . . . . . . . . . . . . . . . .218, 223 Chains . . . . . . . . . . . . . . . . . . .
338 INDEX Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . .30 Vehicle Vehicle Vehicle Vehicle Vehicle Identification Number (VIN) . . . . . . . . . . . .6 Loading . . . . . . . . . . . . . . . . . . . . . . . . .220 Modifications/Alterations . . . . . . . . . . . . . .7 Security Alarm Disarming . . . . . . . . . . . . .14 Storage. . . . . . . . . . . . . . . . . . . . . . .181, 306 Warnings And Cautions . . . . . . . . . . . . . . . . . . . . .6 Warranty Information . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2017 FIAT ® 500 ABARTH 2017 17FX24-126-AD ©2016 FCA US LLC. All Rights Reserved. FIAT is a registered trademark of FCA Group Marketing S.p.A., used under license by FCA US LLC. OWNER’S MANUAL Fourth Edition Printed in U.S.A.
