2013 OWNER’S MANUAL FIAT 500 ABARTH
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .5 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .8 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION The enclosed Warranty Information lists the services that FIAT Group Automobiles offers to its customers: Congratulations on selecting your new vehicle. Be assured that it represents precision workmanship, distinc- • the Warranty Certificate with terms and conditions for tive styling, and high quality - all essentials that are maintaining its validity traditional to our vehicles.
INTRODUCTION 5 HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
6 INTRODUCTION
INTRODUCTION 7 WARNINGS AND CAUTIONS 1 This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . . .11 ▫ To Lock The Doors And Liftgate . . . . . . . . . . . .16 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 ▫ General Information . . . . . . . . . . . . . . . . . . . .16 ▫ Locking Doors With A Key. . . . . . . . . . . . . . . .13 ▫ Transmitter Battery Replacement . . . . . . . . . . .16 ▫ Key-In-Ignition Reminder. . . . . . . . . . . . . . . . .13 䡵 DOOR LOCKS . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Lap/Shoulder Belt Untwisting Procedure . . . . .32 ▫ Air Bag Deployment Sensors And Controls . . . .43 ▫ Seat Belts In Passenger Seating Positions . . . . . .32 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .52 ▫ Automatic Locking Retractor Mode (ALR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . .53 ▫ Energy Management Feature . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 The vehicle is supplied with a code card containing key The key fob contains the Remote Keyless Entry (RKE) code numbers to order duplicate keys, and the authotransmitter with an integrated key. To use the mechanical rized studio that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can key simply press the mechanical key release button . be used to order duplicate keys. A WORD ABOUT YOUR KEYS Ignition Key Removal 1.
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignition Switch Positions 1 — STOP (OFF/LOCK) 2 — MAR (ACC/ON/RUN) 3 — AVV (START) • Before exiting a vehicle, always turn the ignition to the OFF/LOCK position, apply the parking brake, shift the transmission into REVERSE gear, and remove the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition and the ignition switch position is OFF/LOCK, sounds a signal to remove the key. SENTRY KEY姞 CAUTION! An unlocked car is an invitation to thieves.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key which has not been programmed is also Replacement Keys considered an invalid key, even if it is cut to fit the NOTE: Only keys that have been programmed to the ignition switch lock cylinder for that vehicle. vehicle electronics can be used to start the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 General Information The Sentry Key威 system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 2 • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seconds, to unlock all doors and the liftgate. The turn signal NOTE: Changes or modifications not expressly aplights will flash to acknowledge the unlock signal. The proved by the party responsible for compliance could illuminated entry system will also turn on. void the user’s authority to operate the equipment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 1. Press the mechanical key release button and release 2. Rotate the screw located on the side of the Key Fob the mechanical key to access the battery case screw using a small screwdriver. located on the side of the Key Fob. 2 Key Fob Screw Location Mechanical Key Release Button 3. Take out the battery case. Remove and replace the battery observing its polarity.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS The door locks can be manually locked or unlocked from inside the vehicle by using the door handle. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock. Battery Case Removed 4. Refit the battery case inside the Key Fob and turn the screw to lock it into place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • For personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the Key Fob from the ignition.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is incorporated into the door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock. NOTE: To prevent the key from being locked in the vehicle, the power door lock switch will not operate when the key is in the ignition and either front door is open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To change the Autoclose setting in the EVIC, proceed as POWER WINDOWS follows: Power Window Switches 1. Briefly press the MENU ESC button “On” or “Off” There are single window controls located on the shifter will flash on the display (according to the previous bezel, below the climate controls, which operate the setting). driver and passenger door windows. The window con2. Press the + or – button for setting. 3.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE down automatically. To cancel the Auto-Down movement, operate the switch in either the up or down direction and release the switch. Wind Buffeting Power Window Switches Auto-Down — If Equipped Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 To open the liftgate, squeeze the liftgate release handle and pull the liftgate open with one fluid motion. WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All seat belt systems (except the driver’s) include Automatic Locking Retractors (ALRs), which lock the Some of the most important safety features in your seat belt webbing into position by extending the belt vehicle are the restraint systems: all the way out and then adjusting the belt to the • Three-point lap and shoulder belts for all seating desired length to restrain a child seat or secure a large positions item in a seat — if equipped OCCUPANT RESTRAIN
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Here are some simple steps you can take to minimize the You should read the instructions provided with your child restraint to make sure that you are using it properly. risk of harm from a deploying air bag: 1. Children 12 years old and under should always ride 2. All occupants should always wear their lap and shoulder belts properly. buckled up in a rear seat.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided in ⬙If You Need Consumer Assistance.⬙ WARNING! • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. of the worst injuries happen when people are thrown from the vehicle.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 2. The seat belt latch plate is along side the pillar near the 3. When the belt is long enough to fit, insert the latch back of your seat. Grasp the latch plate and pull out plate into the buckle until you hear a “click.” the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of injury in a collision.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Lap/Shoulder Belt Untwisting Procedure The belt will automatically retract to its stowed posi- Use the following procedure to untwist a twisted lap/ tion. If necessary, slide the latch plate down the shoulder belt. webbing to allow the belt to retract fully. 1. Position the latch plate as close as possible to the anchor point.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt” under the “Child Restraints” section. The chart below defines the type of feature for each seating position.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the Automatic Locking Mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Seat Belt Pretensioners Enhanced Seat Belt Use Reminder System The seat belts for both front seating positions are (BeltAlert姞) equipped with pretensioning devices that are designed to BeltAlert威 is a feature intended to remind the driver and remove slack from the seat belt in the event of a collision. front passenger (if equipped with front passenger These devices may improve the performance of the seat BeltAlert威) to fasten their seat belts.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unbuckled while traveling at speeds greater than 5 mph Seat Belt Extender (8 km/h), BeltAlert威 will provide both audio and visual If a seat belt is too short even when fully extended and notification. when the adjustable upper shoulder belt anchorage (if The front passenger seat BeltAlert威 is not active when the equipped) is in its lowest position, your authorized front passenger seat is unoccupied.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Driver Side Knee Air Bag mounted in the instrument panel below the steering column. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Driver and Front Passenger Advanced Front and rear passengers sitting next to a window. The SABIC Air Bags are certified to the Federal regulations for are located above the side windows. The trim covering the SABIC is labeled SRS AIRBAG. Advanced Air Bags. The Advanced Front Air Bags are designed to allow the This vehicle is equipped with Supplemental Seat-Mounted air bags to have different inflation levels based on several Side Air Bags (SAB).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • Steering Wheel and Column Advanced Front Air Bag Features • Instrument Panel The Advanced Front Air Bag system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors that are calibrated to deploy the Seat-Mounted Side Air Bags (SAB) and SABIC during impacts that require air bag occupant protection. WARNING! • Your vehicle is equipped with left and right SABIC, do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the side curtain air bag is located should remain free from any obstructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Side Air Bags (SAB), and front seat belt pretensioners, as required, depending on several factors, including the severity and type of impact. Advanced Front Air Bags and Supplemental Driver Side Knee Air Bag are designed to provide additional protection by supplementing the seat belts in certain frontal collisions depending on several factors, including the Air Bag Deployment Sensors And Controls severity and type of collision.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The side air bags will not deploy in all side collisions. The ORC contains a backup power supply system that Side air bag deployment will depend on the severity and may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. type of collision. Also, the ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition is first turned on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized studio service the air bag system immediately.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A large quantity of non-toxic gas is generated to inflate the Supplemental Driver Side Knee Air Bag. The trim cover separates and folds out of the way allowing the air bag to inflate to the full size. The air bag fully inflates in about 15 to 20 milliseconds. The Supplemental Driver Side Knee Air Bag gas is vented through small vent holes in the side of the air bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 A quantity of non-toxic gas is generated to inflate the side curtain air bag. The inflating side curtain air bag pushes the outside edge of the headliner out of the way and covers the window. The air bag inflates in about 30 milliseconds (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain air bag inflates.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Carefully check the vehicle for fuel leaks in the engine System Reset Procedure compartment and on the ground near the engine comAfter an impact causing air bag deployment, the left and partment and fuel tank before resetting the system and right turn signal lights, located in the instrument panel starting the engine. cluster, will both be blinking, until the ignition is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Customer Action 6. Turn Left Turn Signal Switch ON. 7. Turn Left Turn Signal Switch OFF. (Turn Signal Switch Must be placed in Neutral State). 8. Turn ignition OFF. 9. Turn Hazard Flashers OFF (Manually). Customer Will See Left Turn Light is ON SOLID. Right Turn Light is ON SOLID. Left Turn Light is OFF. Right Turn Light is OFF. System is now reset and the engine may be started.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the air bags, any or all of the following may occur: irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the Body Control Module (BCM) fuse block inside the vehicle for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • How various systems in your vehicle were operating; To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to make sure you have the correct seat for your child. Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight or Age Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-gr
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children should remain rearward-facing until they reach the highest weight or height allowed by their convertible Safety experts recommend that children ride rearwardchild seat. facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear WARNING! facing child safety seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 convertible child seats used in the forward-facing direction are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. WARNING! • Improper installation can lead to failure of an infant or child restraint.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seatback, should use the seat belt in a rear seat. Use this 4. Is the lap part of the belt as low as possible, touching simple 5-step test to decide whether the child can use the the child’s thighs and not their stomach? vehicle’s seat belt alone: 5. Can the child stay seated like this for the whole trip? 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Recommendations For Attaching Child Restraints Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 LATCH Positions For Installing Child Restraints In This Vehicle • • Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol 2
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes, all. Never “share” a LATCH anchorage with two or more child restraints.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along gap between the seatback and seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 LATCH-compatible child restraint systems will be To Install A LATCH-compatible Child Restraint equipped with a rigid bar or a flexible strap on each side. 1. If the selected seating position has a Switchable AutoEach will have a hook or connector to attach to the lower matic Locking Retractor (ALR) seat belt, stow the seat anchorage and a way to tighten the connection to the belt, following the instructions below. See the section anchorage.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 5. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of the restraint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Weight limit of the Child Restraint Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? Yes, all.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you position. For some second row seats, you may need to will hear a clicking sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 8. If the child restraint has a top tether strap and the Installing A Child Restraint With A Cinching seating position has a top tether anchorage, connect Latch Plate (CINCH) — If Equipped the tether strap to the anchorage and tighten the tether 1. Place the child seat in the center of the seating strap. Refer to “Lower Anchors and Tethers for Chilposition.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “Lower Anchors and Tethers for Children (LATCH) Restraint System” for directions to attach a tether anchor. facing out, away from the child restraint. Repeat steps 4 to 6, above, to complete the installation of the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 2 3.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Safety Checks You Should Make Inside The Vehicle Seat Belts not lit during starting, see your authorized studio. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized studio. Inspect the belt system periodically, checking for cuts, Defroster frays, and loose parts. Damaged parts must be replaced Check operation by selecting the defrost mode and place the immediately. Do not disassemble or modify the system.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel bolts for tightness. Check the tires for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 POWER CONVERTIBLE TOP — IF EQUIPPED . .84 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . .90 ▫ Lowering The Power Top. . . . . . . . . . . . . . . . .85 ▫ Sun Visors . . . . . . . . . . . . . . . . . . . . . . . . . . .91 ▫ Raising The Power Top . . . . . . . . . . . . . . . . . .85 䡵 BLUE&ME™ HANDS-FREE COMMUNICATION — IF EQUIPPED . . . . . . . .91 ▫ Power Convertible Top Relearn Procedure . . . . .86 ▫ Overview . . . . . . . . . . . . . . . .
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ EZ Entry Feature . . . . . . . . . . . . . . . . . . . . . .101 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . .109 ▫ Memory Feature . . . . . . . . . . . . . . . . . . . . . .102 ▫ Follow Me Home/Headlight Delay . . . . . . . . .109 ▫ Heated Seats — If Equipped . . . . . . . . . . . . .102 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . .109 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .118 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .126 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . .118 ▫ Emergency Operation. . . . . . . . . . . . . . . . . . .127 䡵 REAR PARK ASSIST — IF EQUIPPED . . . . . . . .119 ▫ Sun Shade — If Equipped . . . . . . . . . . . . . . .127 ▫ Rear Park Assist Sensors . . . . . . . . . . . . . . . .120 䡵 ELECTRICAL POWER OUTLETS . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER CONVERTIBLE TOP — IF EQUIPPED On vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, which is used to open the power top, and the driver side button, which is used to close the power top. Power Convertible Top Switch NOTE: The power top buttons will operate when the ignition switch is turned to the ACC/ ON/RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Lowering The Power Top Press the top open button approximately one second for the partially open position. Press the top open button for approximately one second a second time to fully open the convertible top. Raising The Power Top From the convertible top fully open position, press the top close button for approximately one second for the partially open position.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants in a collision. Therefore, it is important that all occupants wear their seat belts at all times. Death or serious injuries could occur if you are ejected from the vehicle during a collision. 3. Hold the OPEN button to move the top to the fully open position. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Auto Open/Close will now be functional. Trunk lid Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night operation will be functional. position (toward the rear of the vehicle). The mirror NOTE: DO NOT interrupt this activity. should be adjusted while set in the day position (toward If the power convertible top does not relearn repeat the the windshield). procedure a second time.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in reverse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 The power mirror controls consist of a mirror select The power mirror controls are located on the driver’s switch and a four-way mirror control switch. To adjust a mirror, press the mirror select switch to either the L (left) door trim panel. or R (right) to select the mirror you need to adjust. Power Mirrors Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Spotter Mirror — If Equipped Folding Mirrors Some models are equipped with a driver’s side spotter The exterior mirrors are hinged to allow the mirror to mirror. The spotter mirror allows for a greater range of pivot forward or rearward to help avoid damage. The visibility on the driver’s side of the vehicle. mirror has three detent positions: full forward, normal and full rearward. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Sun Visors BLUE&ME™ HANDS-FREE COMMUNICATION — The driver and passenger sun visors are located on the IF EQUIPPED headliner, near the front windshield. The sun visor can be Overview rotated downward or up against the door glass. Both sun Windows Mobile™-based FIAT BLUE&ME™ is a pervisors are equipped with courtesy mirrors. sonal telematic system enabling you to use communication and entertainment applications expressly designed for use in the car.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE you are not required to train the voice recognition system to recognize your voice. This implies that the system is nearly equally performing with different persons, i.e.: the voice recognition system is of the “speaker independent” type. The Hands-Free Kit The basic characteristic of this hands-free kit is voice recognition with Bluetooth威 wireless technology.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 your mobile phone manually and visually using the For further details on the mobile phones supported by steering wheel controls and the instrument panel multi- BLUE&ME™, refer to section BLUE&ME™ SUPPORTED function display. MOBILE PHONES. To get started with BLUE&ME™ hands-free kit with voice recognition, you have to simply pair your Bluetooth威 wireless technology enabled mobile phone with the system. Pairing is an operation that has to be made only once.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE list or directly pronouncing the phone number, to (LAST CALLS and PHONEBOOK ) and the media answer a call and also to answer another incoming player. To activate settings when travelling you can only use voice commands. phone call. • To interact with BLUE&ME™ you can use either the The hands-free kit enables the following operations: buttons on the steering wheel or voice commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • To Answer A Call — you can answer an incoming call After pairing and connecting your phone with the by pressing the MENU/Phone button on the steering BLUE&ME™ system, you can make phone calls by speaking keywords or pressing buttons on the steering wheel. wheel.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Not all mobile phones support the SMS text • To call the SMS text sender using the buttons on the message reader function or automatic phonebook transsteering wheel or voice commands. fer via Bluetooth威. Consult www.fiatusa.com for further • To delete individual messages or the entire inbox using information on the list of compatible mobile phones. the buttons on the steering wheel or voice commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 In this way, while you are driving you can play your NOTE: favorite music collections. • The media player does not support audio files compressed with other formats and DRM (Digital Right • iPod威 Player — see dedicated paragraph under Media Management) protected audio files. Non-supported Player Functions. audio files that may be present on the USB device will The media player enables the following operations: be ignored.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences; for this reason certain functions shall be disabled by the BLUE&ME™ system until driving conditions are secure and, if required, only when the car is stopped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. Recline Adjustment The recline adjustment lever is located on the inboard side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Seat Height Adjustment EZ Entry Feature The driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height. The driver and front passenger seats have an EZ entry feature for rear seat passengers.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lift the seatback upright and push the seat rearward to fore/aft (memory) position on the tracks. This results in the seat back memory being set only – The track will then its locked position once the rear passengers are seated. be locked forward of its last set fore/aft memory posiMemory Feature tion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE downward on the head restraint. Refer to “Occupant TO OPEN AND CLOSE THE HOOD Restraints” in “Things To Know Before Starting Your To open the hood, two latches must be released. Vehicle” for information on tether routing. 1. Pull the bottom of the RED hood release lever, located on the left kick panel, rearward. Push Button Hood Release Lever 2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 3 Hood Safety Latch Location Hood Prop Rod Lift the hood prop rod that clips to the right side (left side In hot climates, the prop rod may be hot. Pick up the prop when standing in front of the hood) of the engine rod at the foam on the end of the prop rod. compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in the open position.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open 8 in (20 cm) approximately and then drop it. This should secure both latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 High Beams With the low beams activated, push the multifunction lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steering wheel. This will turn on the high beams until the lever is released.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O symbol. NOTE: The low beams and side/taillights will not be on with DRL. The DRL function can be turned on or off using the display menus. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Lane Change Assist Deactivation Tap the lever up or down once, without moving beyond Pull the multifunction lever toward the steering wheel the detent, and the turn signal (right or left) will flash and hold it for more than two seconds. three times then automatically turn off. Interior Lights Follow Me Home/Headlight Delay The interior light switches are located in the overhead When this feature is selected the driver can choose to console.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • When the doors are unlocked with Key Fob a 10 second timer is activated. Before getting out of the vehicle be sure that the switch is in the center position or that the lights are off to avoid draining the battery. • When the doors are locked with the Key Fob the lights will turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Front Fog Lights — If Equipped WINDSHIELD WIPERS AND WASHERS The fog light switch is located on the center stack of the The windshield wiper/washer lever is located on the instrument panel, just below the radio. right side of the steering column. NOTE: The windshield wipers/washers will only operate with the ignition in the ON/RUN position. Fog Light Switch Press the switch once to turn the front fog lights on.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Windshield Wiper Operation Windshield Wiper Off There are five different modes of operation for the front This is the normal position of the wiper lever. windshield wipers. The windshield wiper lever can be Intermittent Wiper Operation raised or lowered to access these modes: Push the lever downward to the first detent. The wipers will operate intermittently.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Manual High Speed/Mist Push the lever upward from the off position. The wipers will operate at high speed to clear off road mist or spray from a passing vehicle. This operation will continue until the lever is released. When the lever is released, the wipers will return to the off position and automatically shut off. Front Windshield Washer Operation Pull the windshield wiper/washer lever toward the steering wheel to activate the washers.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Windshield Wiper Rotate the end of the windshield wiper/washer lever upward to the first detent past the intermittent settings for intermittent wipe operation. With the front windshield wiper active, rotate the end of the windshield wiper/washer lever upward. The rear wiper will operate in the same mode as the front windshield wipers, but at half the frequency.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Rear Windshield Washer Operation Push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. 3 TILT STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. ELECTRONIC SPEED CONTROL When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: In order to ensure proper operation, the Electronic Speed Control system has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control system can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the RES (+) button once will result in a 1 mph (1.6 km/h) increase in set speed. Each subsequent tap of A soft tap on the brake pedal, pushing the CANC button, the button results in an increase of 1 mph (1.6 km/h). or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the To decrease speed while the Electronic Speed Control is set speed memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Using Electronic Speed Control On Hills REAR PARK ASSIST — IF EQUIPPED The transmission may downshift on hills to maintain the The Rear Park Assist system provides an audible indicavehicle set speed. tion of the distance between the rear fascia/bumper and a detected obstacle when backing up, e.g. during a NOTE: The Electronic Speed Control system maintains parking maneuver. Refer to the “Park Assist System speed up and down hills.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Sensors Rear Park Assist Alerts The four Rear Park Assist sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors’ field of view.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Audible And Visual Signals Supplied By The Rear Park Assist System SIGNAL Obstacle Distance Failure MEANING An obstacle is present within the sensors’ field of view Sensor or System failures INDICATION Audible signal (dashboard loudspeaker) • Sound pulses emitted at a rate that increases as the distance decreases. • Emits continuous tone at 12 in (30 cm) • Adjustable volume level. (Refer to “Menu Functions” for further information).
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Failure Indications Cleaning The Rear Park Assist System A malfunction of the Rear Park Assist sensors or system Clean the Rear Park Assist sensors with water, car wash is indicated, during REVERSE gear engagement, by the soap and a soft cloth. Do not use rough or hard cloths. In instrument panel warning icon.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • Clean the Rear Park Assist sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The Rear Park Assist system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/bumper. • Objects such as bicycle carriers, etc.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when backing up even when using the Rear Park Assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 POWER SUNROOF — IF EQUIPPED The power sunroof roof switch is located in the overhead console. Power Sunroof Switch WARNING! • Never leave children in a vehicle with the key in the ignition switch (or with the ignition in the Accessory or Run position, for vehicles equipped with Keyless Enter-N-Go™). Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Open Pinch Protect Feature Press and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Press the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Emergency Operation In case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. Insert the hex wrench and turn, moving the sunroof to the desired location.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power is available when the ignition switch is in the There is a standard 12 Volt (13 Amp) power outlet, ON/RUN or START position. Insert the cigar lighter or located in the floor console, for added convenience. This accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating power outlet can power mobile phones, electronics and position. other low power devices.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 For rear passengers, there are cupholders located on the For the driver and front passenger, cupholders are lo- floor between the front driver and passenger seats. cated on the floor console between the front seats.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE CARGO AREA FEATURES Glove Box Compartment The rear seatbacks have a fold down feature to allow increased cargo capacity. The glove box is located on the right side of the instrument panel. Pull outward on the door latch to open the Push down the release button, located at the outboard glove box. Push the glove box door upward to close it. top of the seatback and move the seatback to its foldeddown position to provide a flat load floor cargo area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 3 Rear Seat Release Buttons Folded Rear Seats
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 20 minutes. To manually shut the defroster off, push the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .137 ▫ Trip Computer . . . . . . . . . . . . . . . . . . . . . . .155 䡵 TURBO BOOST GAUGE . . . . . . . . . . . . . . . . . .138 ▫ Trip Button . . . . . . . . . . . . . . . . . . . . . . . . . .156 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .139 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . . .157 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .140 ▫ Values Displayed . . . . . . . . . . . .
136 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . .172 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . .196 ▫ General Information. . . . . . . . . . . . . . . . . . . .175 ▫ Operating Instructions — Hands-Free Phone (If Equipped). . . . . . . . . . . . . . . . . . . . . . . . .196 ▫ Functions And Adjustments . . . . . . . . . . . . . .176 ▫ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 137 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 6 — — — — — — Side Vent Multifunction Lever – Light Control Instrument Cluster And Warning Lights Windshield Wiper, Washer, Trip Computer Central Air Vents Storage Compartment/Radio 7 — Passenger Air Bag 8 — Glove Compartment 9 — Rear Defrost Button 10 — Hazard Button 11 — Climate Controls 12 — Power Windows Control 13 14 15 16 17 — — — — — Storage Compartment Shift Lever Sport Button Horn/Driver Airbag Boost Gauge
138 UNDERSTANDING YOUR INSTRUMENT PANEL TURBO BOOST GAUGE Your vehicle is equipped with a boost gauge and integrated shift light indicator located to the left of the instrument cluster. The boost gauge indicates the intake manifold pressure relative to barometric pressure. The engine management system in your vehicle intelligently regulates intake manifold pressure based on environmental (ambient) and engine operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 139 INSTRUMENT CLUSTER 4
140 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 2. Rear Defrost Button 1. Glow Plug Light — If Equipped Press and release this button to turn on the rear window defroster. This indicator will illuminate The Glow Plug light will flash during engine oil when the rear window defroster is on. The rear window viscosity sensor measurement in cold weather. defroster automatically turns off after 20 minutes. During this measurement (up to 10 seconds), the starter will be disabled.
UNDERSTANDING YOUR INSTRUMENT PANEL 141 CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. 6. Park/Headlight ON Indicator / Follow Me Home (Headlight Delay) Indicator — If Equipped This indicator will illuminate when the park lights or headlights are turned on. If the Follow Me Home feature is activated this indicator will illuminate and the EVIC will show how 3.
142 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Generic Warning Light 10. Cruise Indicator — If Equipped The Generic Warning Light will illuminate if This indicator shows that the Speed Control system is on. any of the following conditions occur: Oil Change Request, Engine Oil Pressure Sensor Failure, External Light Failure, Fuel Cut-Off 11. Seat Belt Reminder Light Intervention, Fuel Cut-Off Not Available, Parking Sensor Failure.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 12. Charging System Light 14. Electronic Throttle Control (ETC) Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned to ON/RUN and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
144 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 alternate tires or wheels on the vehicle that prevent the 16. Automatic Gearbox Failure TPMS from functioning properly. Always check the This light will illuminate when there is an TPMS malfunction telltale after replacing one or more automatic transmission fault. tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. 17.
146 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBDII, that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF/LOCK to ON/RUN, have the condition checked promptly.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 19. Engine Temperature Warning Light 20. Brake Warning Light This light warns of an overheated engine condition. The engine coolant temperature indicator will illuminate and a single chime will sound after reaching a set threshold. This light monitors various brake functions, including brake fluid level and parking brake application.
148 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with the Anti-Lock Brake System 21. Electronic Stability Control OFF (ESC OFF) Indica(ABS), are also equipped with Electronic Brake Force tor Light Distribution (EBD). In the event of an EBD failure, the This light indicates the Electronic Stability ConBrake Warning Light will turn on along with the ABS trol system (ESC) has been turned off by the Light. Immediate repair to the ABS system is required. driver.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock The ESC Off Indicator Light and the ESC Activation/ brakes. If the ABS light does not turn on when the Malfunction Indicator Light come on momentarily each ignition switch is turned to the ON/RUN position, have time the ignition switch is turned to ON/RUN. the light inspected by an authorized dealer.
150 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! (Continued) Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “280“, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “280”, and you hear continuous chimes, turn the engine off immediately and call an authorized studio for service. Vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 service, so that you can be sure that it is properly reset, or NOTE: The fuel gauge and range will not immediately that the door jamb sticker is accurate if the odometer update accurately when refueling with the engine on. must be reset at zero. 28.
152 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The EVIC consists of the following: • System Status The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the • Vehicle Information Warning Message Displays instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 Press the DOWN button to scroll downward through The setup menu can be activated by pressing the SET or DOWN the displayed menu and the related options or to de- ESC button. Single presses on the UP buttons will scroll through the setup menu options. crease the value displayed.
154 UNDERSTANDING YOUR INSTRUMENT PANEL • Button Volume • Hill Start • GSI Shift Up • Daylights (D.R.L.) • Exit Menu Selecting An Option Of The Main Menu With Submenu 1. Briefly press the SET ESC button to display the first submenu option. or DOWN button (by single 2. Press the UP presses) to scroll through all the submenu options. Selecting An Option Of The Main Menu Without 3. Briefly press the SET ESC button to select the disSubmenu played submenu option and to open the relevant setup menu. 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 6. Press and hold the SET ESC button to return to the indicator system (after performing the scheduled mainmain menu (short hold) or the main screen (longer tenance), refer to the following procedure. hold). 1. Turn the ignition switch to the ON position.(Do not start the engine.) Change Engine Oil Indicator System Change Engine Oil Your vehicle is equipped with an engine oil change indicator system.
156 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the reset operation occurs in the presence of the screens concerning Trip A or Trip B, only the inforThe TRIP button, located on the right steering column mation associated with Trip A or Trip B functions will be stalk, can be used to display and to reset the previously reset. described values. Start Of Trip Procedure • A short button press displays the different values.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 NOTE: “Trip B” functions may be excluded (see “Trip B Both trip functions are resettable (reset — start of new Data”). “Range” and “Instantaneous consumption” cannot be reset. trip).
158 UNDERSTANDING YOUR INSTRUMENT PANEL Distance Travelled Personal Settings (Customer-Programmable This value shows the distance covered since the last reset. Features) Dimmer Average Consumption The EVIC display is provided with a light sensor capable This value shows the approximate average consumption of detecting environmental light conditions and adjustsince the last reset. ing the brightness of the instruments accordingly.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 2. Briefly press the SET ESC button to go back to the 3. When the function is activated (On), briefly press the SET ESC button to display the presently set activation menu screen or press and hold the SET ESC (approxispeed. Pressing the UP or DOWN buttons mately one second) to go back to the main screen selects the speed limit. Press SET ESC to confirm without storing settings. selection.
160 UNDERSTANDING YOUR INSTRUMENT PANEL To cancel the setting, proceed as follows: For activation / deactivation, proceed as follows: 1. Briefly press the SET ESC button. “On” will flash on 1. Briefly press the SET ESC button. “On” or “Off” will flash on the display (according to previous setting). the display. 2. Press the DOWN display. button. “Off” will flash on the 2. Press the UP setting. or DOWN button to select the 3. Briefly press the SET ESC button to go back to the 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 Proceed as follows: NOTE: 1. Briefly press the SET ESC button. The display will • The setting will increase or decrease by one unit each time the UP or DOWN button is pressed. Press show the two sub-menu items “Time” and “Mode.” and hold the button to increase/decrease the setting or DOWN button to navigate the 2. Press the UP rapidly. Save the setting by briefly pressing the button two sub-menu items. when you approach the required setting. 3.
162 UNDERSTANDING YOUR INSTRUMENT PANEL or DOWN button for setting. sub-menu screen, or press and hold the SET ESC button 6. Press the UP (approximately one second) to go back to the main screen NOTE: The setting will increase or decrease by one unit without storing the settings. or DOWN button is pressed. each time the UP Set Date or DOWN button to Press and hold the UP increase/decrease the setting rapidly.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 To activate (On) or to deactivate (Off) the sound system To activate (On) or to deactivate (Off) the speed display feature, proceed as follows: info displaying proceed as follows: 1. Briefly press the SET ESC button “On” or “Off” will 1. Briefly press the SET ESC button. “MPH”, “km/h”, then “Off” will flash on the display (according to flash on the display (according to the previous setprevious setting). ting). 2. Press the UP or DOWN button for setting. 2.
164 UNDERSTANDING YOUR INSTRUMENT PANEL To change the setting proceed as follows: 2. Press the UP or DOWN three sub-menus. button to navigate the 1. Briefly press the SET ESC button “On” or “Off” will flash on the display (according to the previous set- 3. Select the required sub-menu and then briefly press the SET ESC button. ting). or DOWN button for setting. 4. When accessing the “Distance” submenu: briefly press the SET ESC button. Either “mi” or “km” will appear 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 If the distance unit set is “km,” the fuel economy unit will or press and hold the SET ESC button (approximately one second) to go back to the main screen without storing be displayed in either km/l or l/100km. the settings. or DOWN button for setting. 1. Press the UP Language (Selecting The Language) 2. Briefly press the SET ESC button to return to the The messages can be displayed in the following lansub-menu.
166 UNDERSTANDING YOUR INSTRUMENT PANEL Buzzer Volume (Adjusting The Failure/Warning Buzzer Volume) Button Volume (Button Volume Adjustment) This function may be used to adjust the volume of the With this function the volume of the buzzer accompany- beep accompanying the buttons. SET ESC, UP or buttons can be adjusted according to 8 levels. ing any failure/warning indication can be adjusted to DOWN one of eight volume levels.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Hill Start Assist GSI Shift Up This function is used when starting a vehicle from a stop on a hill. Hill Start Assist maintains the same level of brake pressure the driver applied for a short period of time after the foot has been removed from the brake pedal. With this function active, the boost gauge will display a shift up message and up arrow at the appropriate time of shift. To change the setting proceed as follows: 1.
168 UNDERSTANDING YOUR INSTRUMENT PANEL Proceed as follows to switch this function on or off: Exit Menu 1. Briefly press the SET ESC button to display the three This function closes the initial menu screen. sub-menus. Briefly press the SET ESC button to go back to the main 2. Briefly press the SET ESC button. “On” or “Off” will screen. flash on the display (according to previous setting). button to return to the first menu option Press the 3. Press the UP or DOWN button for setting. (Speed Beep).
UNDERSTANDING YOUR INSTRUMENT PANEL 169 SALES CODE (RAB) RADIO If the radio has BLUE&ME™, refer to the appropriate “BLUE&ME™ User’s Manual” for further information. The instructions for use are given below and we recommend you to read them carefully. Suggestions Road Safety Please, learn how to use all different radio functions (e.g. store stations) before beginning to drive. Reception Conditions Reception conditions change constantly while driving.
170 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Having the volume turned up high can cause the driver to not be able to hear important traffic sounds, i.e. sirens, horns, etc. This could cause an accident. Always adjust the volume so that you can still hear background noises. Care And Maintenance • Clean every CD thoroughly removing any finger marks or dust using a soft cloth. Hold CDs by the outside and clean them from the middle outwards. • Never use chemicals (e.g.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 • The use of original CD media is required for the best • The CD player is capable of reading most compression quality audio production. Correct operation is not systems currently in use, following the development of these systems, the reading of all compression formats guaranteed when CD-R/RW media are used that were is not guaranteed. not correctly burned and/or with a maximum capacity above 650 Mb.
172 UNDERSTANDING YOUR INSTRUMENT PANEL With Bose威 Premium Audio system (if equipped): • A subwoofer under the right front seat. • Two 165 mm diameter midwoofer speakers. • An amplifier in the trunk on the right-hand side panel. • Two 11 mm tweeter speakers in the front pillars. • Antenna on the car roof. • Two 100 mm full range speakers, one speaker in each • Radio with CD/MP3 player. of the rear side panels.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 BUTTON (Mute/Pause Button) AUDIO (Information Button) GENERAL FUNCTIONS Volume activation/deactivation (Mute/Pause) Audio adjustments: low tones (BASS), high tones (TREBLE), left/right balance (BALANCE), front/rear balance (FADER) MENU Song, Artist, Album, Genre, Playlist, Folder information (if available) in CD, Media Player and Satellite (if so equipped); Toggles RBDS information in FM Advanced functions adjustment +Vol/–Vol Volume adjustment MODE Short butt
174 UNDERSTANDING YOUR INSTRUMENT PANEL BUTTON RADIO FUNCTIONS Radio Station Search: • Automatic Search • Manual Search 12345 Current radio station storing Stored station recall BUTTON CD FUNCTIONS CD ejection Previous/next track play CD track fast forward/rewind Previous/next folder play (for CD-MP3) MODE Automatic search: press buttons or (long press for fast forward) Manual search: press buttons or (long press for fast forward) Long button press for memory preset 1 to 5 respectively Short button p
UNDERSTANDING YOUR INSTRUMENT PANEL 175 General Information CD Section The radio offers the following functions: • Track selection (forward/backward) Radio Section • Fast forward/rewind through tracks • PLL tuning with FM/AM/MW frequency bands • CD Display function: display of track number and on mp3 discs (song title, artist) and time elapsed since start of the track • RBDS (Radio Broadcast Data System) • Automatic/manual station tuning • FM Multipath detector • Manual storing of 25 stations (base
176 UNDERSTANDING YOUR INSTRUMENT PANEL CD/MP3 Section • Separate bass/treble tone adjustment • MP3-Info function (ID3-TAG) • Right/left channel balancing • Folder selection (previous/next) • Front/rear fader • Track selection (forward/backward) Functions And Adjustments • Fast forward/rewind through tracks Turning The Car Radio On (ON/OFF) button is • MP3 Display function: display of folder name, ID3- The car radio comes on when the pressed briefly.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 Press the button again to deactivate the MUTE function. The volume will gradually increase until it reaches By pressing the TUNER button briefly and repeatedly, the previously set level. the following audio sources can be selected cyclically: When the volume level is changed using the dedicated • AM, FM and Satellite Bands (if equipped) controls, the Mute function is deactivated and the volSelecting The CD Function ume is adjusted to the new level selected.
178 UNDERSTANDING YOUR INSTRUMENT PANEL or to scroll through the Menu Tone Adjustment Use the buttons functions. To change the setting of the selected function, Proceed as follows: or buttons. use the 1. Press AUDIO button. The current status of the selected function appears on the or button to select “Bass” or “Treble” 2. Press the display. in the AUDIO menu. The functions managed by the Audio Menu are: or button or to increase/decrease the 3. Press the • BASS (Bass adjustment) bass or treble adjustments.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 3. Press the button to increase the sound from the left By pressing the or buttons briefly, the levels will button to increase the sound from change progressively. By pressing them down longer, the speakers or the the right speakers. levels will change quickly. or buttons briefly, the levels will Select the value “0” to set the right and left audio outputs By pressing the change progressively. By pressing them down longer, the at the same level.
180 UNDERSTANDING YOUR INSTRUMENT PANEL Preset/User*/Classic/Rock/Jazz Functions — If Equipped When one of the equalizer adjustments is activated the wording “EQ” lights up. The built-in equalizer can be activated/deactivated. When the equalizer function is off, the audio settings can only be changed by adjusting the “Bass” and “Treble” settings, whereas when the function is on, the acoustic curves can be adjusted. To deactivate the equalizer, select the “EQ Preset” function in the audio menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 Menu • SiriusXM™ Telephone Number MENU Button Functions • System Reset Press the MENU button briefly to activate the Menu • Speed Volume function. • On Volume Limit or buttons to scroll through the menu Use the Press the MENU button again to exit the Menu function. functions. To change the setting of the selected function, or buttons.
182 UNDERSTANDING YOUR INSTRUMENT PANEL • “On volume limit: off” – The radio will come on at the same volume as before it was switched off. The This function makes it possible to activate/deactivate the volume level can be between 0 and 40. maximum volume limit when turning the radio on. or to change the setting.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 • YES — The default parameters will be restored. During such operation, the wording “Resetting” appears This function makes it possible to set the radio switching on the display. At the end of the operation, the source off mode by choosing between two methods. does not change and the previous situation will be The chosen mode appears on the display: displayed.
184 UNDERSTANDING YOUR INSTRUMENT PANEL To listen to a preset station, select the desired frequency band and then briefly press the corresponding preset With the Radio mode active, press the FM or AM tuner button briefly and repeatedly to select the desired recep- button (from 1 to 5). tion band. By pressing the preset button for more than 2 seconds, Each time the button is pressed the following bands are the tuned station will be stored.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far from the This is used to manually search for stations in the antenna as possible. Do not place items directly on or preselected band. above the antenna.
186 UNDERSTANDING YOUR INSTRUMENT PANEL logos are trademarks of SiriusXM™ Radio Inc. and its subsidiaries. SiriusXM™ Radio requires a subscription, sold separately after trial subscription included with vehicle purchase. Prices and programming are provided by SiriusXM™ and are subject to change. Subscriptions governed by Terms & Conditions available at sirius.com/ service terms. SiriusXM™ Radio U.S. service only available to those at least 18 years of age in the 48 contiguous United States, D.C., and PR.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 Write down the Electronic Serial Number (ESN) for your receiver. To retrieve the Electronic Serial Number of SiriusXM™ Satellite Receiver Module tune to Channel 0. Make sure that when the order is placed, the ESN are correct. If any of the ESN numbers are not entered correctly, then the SiriusXM™ subscription will not be able to be transferred to the new radio and will not be active when installed in the customer’s vehicle.
188 UNDERSTANDING YOUR INSTRUMENT PANEL The following are instructions for retrieving the Elec- CD Player Selection tronic Serial Number (ESN) from FIAT 500 NAFTA model To activate the CD player built into the equipment, radios: proceed as follows: To retrieve the ESN of SIRIUS Satellite Receiver Module • Load a CD with the equipment switched on. The first tune to Channel 0. Make sure that when the order is track will start to play. placed, the ESN are correct.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 If the CD is not removed from the radio, it will automatically be reloaded about 20 seconds later but will not To load the CD, insert it gently into the slot to activate the resume playing until the ⬙MEDIA⬙ button is pressed to motorized loading system, which will position it corselect the CD mode. The radio will switch to the last rectly. source prior to CD mode. The CD can be loaded with the radio off and the ignition The CD cannot be ejected if the radio is off.
190 UNDERSTANDING YOUR INSTRUMENT PANEL Display Information Track Fast Forward/Rewind When the CD player is operating, information will ap- Keep the button pressed down to fast forward the button pressed down to pear on the display with the following meaning: selected track and keep the fast rewind the track. The fast forward/rewind will stop • “Track 5” indicates the CD track number. once the button is released.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 • The sampling frequencies that can be reproduced are: 44.1 kHz, stereo (from 96 to 320 kbit/s) – 22.05 kHz, In addition to playing regular audio CDs, the radio is also mono or stereo (from 32 to 80 kbit/s). enabled to play CDROMs on which compressed audio files have been recorded in an MP3 format. • Tracks with a variable bit-rate can be reproduced.
192 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When the function is activated the radio may take a few seconds to start playing. While checking the disc the display will show “CD Reading.” If no MP3 files are detected, the radio will resume playing the audio session from the point where it was interrupted. Press the button to select a next folder or the button to select the previous folder. The display will show the number of the folder. Display Information The folders are selected cyclically.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 • If the MP3 files on a CD-ROM are structured in CD Player sub-folders their structure is compressed to a single The CD Does Not Play level structure, where the sub-folders are taken to the The CD is dirty. Clean the CD. level of the main folders. Troubleshooting The CD is scratched. Try using another CD. General The CDCan Not Be Loaded Sound Volume Low A CD is already loaded. Press the the CD.
194 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Hands-Free Phone (If Equipped) Refer to the appropriate “BLUE&ME™ User’s Manual” for further information. Personal/Portable Navigation Device (PND) — If Equipped A Personal/Portable Navigation Device (PND) is available as optional equipment for this vehicle, refer to the Navigation User Guide for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 The right-hand control is a rocker-type switch with a The remote sound system controls are located on the rear pushbutton in the center and controls the volume and surface of the steering wheel. Reach behind the wheel to mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom access the switches. of the rocker switch will decrease the volume.
196 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Operating Instructions — Hands-Free Phone Pressing the top of the switch will “Seek” up for the next (If Equipped) listenable station and pressing the bottom of the switch Refer to the appropriate Blue&Me™ User’s Manual for further information. will “Seek” down for the next listenable station.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 5. Store the disc in its case after playing. RADIO OPERATION AND MOBILE PHONES 6. Do not expose the disc to direct sunlight. Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio.
198 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Heating And Air Conditioning 1. Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler temperatures, while rotating to the right into the red area indicates warmer temperatures. 2. Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 • Panel Air is directed through the outlets in the instruContinuous use of the Recirculation mode may make the ment panel. These outlets can be adjusted to direct inside air stuffy and window fogging may occur. Exairflow. tended use of this mode is not recommended.
200 UNDERSTANDING YOUR INSTRUMENT PANEL to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • Defrost Air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in Mix or Defrost, even if the Air Conditioning (A/C) button is not pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Operating Tips Chart 4
202 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control (ATC) — If Equipped • The Automatic Temperature Control (ATC) allows the driver to select individual comfort settings. • The system provides set-and-forget operation for optimum comfort and convenience. • The system can be controlled manually, if desired. The ATC system automatically maintains the interior comfort level desired by the driver and passenger.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 1. AUTO Temperature Control (ATC) Button 4. Blower Control Up Button Controls airflow, temperature, distribution, and air recirculation automatically. Press and release to select. Performing this function will cause the ATC to switch between manual mode and automatic modes. Refer to “Automatic Operation” for more information. There are 12 blower speeds. The blower speed increases as you press this button.
204 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Floor Mode 10. Temperature Control Down Button Air is directed through the floor outlets with a small Provides temperature down control. Push the button for amount flowing through the defrost and side window cooler temperature settings. demister outlets. 11. Climate Control ON/OFF Button 8. Panel Mode Press and release to turn the Climate Control ON or OFF. Air is directed through the outlets in the instrument 12. Recirculation Control Button panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Automatic Operation NOTE: 1. Press the AUTO button on the Automatic Temperature • It is not necessary to move the temperature settings for Control (ATC) Panel, the indicator will illuminate cold or hot vehicles. The system automatically adjusts when on. the temperature, mode and fan speed to provide comfort as quickly as possible. 2.
206 UNDERSTANDING YOUR INSTRUMENT PANEL The blower fan speed can be set to any fixed speed by pressing the blower control up or down buttons. The fan This system offers a full complement of manual override will now operate at a fixed speed until additional speeds features. are selected. This allows the front occupants to control NOTE: Each of these features operates independently the volume of air circulated in the vehicle and cancel the from each other. If any feature is controlled manually, AUTO mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Floor Mode Defrost Mode Air comes from the floor outlets. A slight amount Air comes from the windshield and side window demister outlets. Use Defrost mode with maxiof air is directed through the defrost and side mum temperature settings for best windshield and side window demister outlets. window defrosting. When the defrost mode is selected, Bi-Level the blower will automatically default to medium-high. Air is directed through the panel and floor outlets.
208 UNDERSTANDING YOUR INSTRUMENT PANEL outlets. If Economy mode is desired, press the A/C Recirculation Control button to turn off the A/C mode in the ATC display and When outside air contains smoke, odors, or deactivate the A/C system. high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by NOTE: pressing the RECIRCULATION control button. • If the system is in Mix or Defrost Mode, the A/C can Recirculation mode should only be used temporarily.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Operating Tips Chart 4
210 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Summer Operation Windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning the air conditioning (pressing the A/C button) on will clear the fog. Adjust the temperature control, air direction, and blower speed to maintain comfort.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air using the high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the air conditioning system is started again.
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .216 ▫ Recommended Shift Speeds . . . . . . . . . . . . . .220 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . .216 ▫ Downshifting . . . . . . . . . . . . . . . . . . . . . . . .221 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .216 䡵 DRIVING ON SLIPPERY SURFACES . . . . . . . . .221 ▫ Cold Weather Operation . . . . . . . . . . . . . . . .217 ▫ Acceleration . . . . . . . . . . . . . . . . . . .
214 STARTING AND OPERATING 䡵 SPORT MODE . . . . . . . . . . . . . . . . . . . . . . . . .227 ▫ Tire Identification Number (TIN). . . . . . . . . . .240 䡵 BRAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . .228 ▫ Tire Terminology And Definitions . . . . . . . . . .241 ▫ Four-Wheel Anti-Lock Brake System (ABS) . . .228 ▫ Tire Loading And Tire Pressure . . . . . . . . . . .242 䡵 ELECTRONIC BRAKE CONTROL SYSTEM . . . .230 䡵 TIRES — GENERAL INFORMATION. . . . . . . . .
STARTING AND OPERATING 215 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .251 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . .263 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .252 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . .264 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .252 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . .265 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . .253 ▫ Fuel System Cautions. . . . . .
216 STARTING AND OPERATING STARTING PROCEDURES Manual Transmission Before starting your vehicle, adjust your seat, adjust both Apply the parking brake, place the shift lever in NEUinside and outside mirrors, and fasten your seat belts. TRAL, and press the clutch pedal before starting the vehicle. This vehicle is equipped with a clutch interlocking ignition system. It will not start unless the clutch WARNING! pedal is pressed to the floor.
STARTING AND OPERATING 217 Cold Weather Operation Extended Park Starting To prevent possible engine damage while starting at low temperatures, this vehicle will inhibit engine cranking when the ambient temperature is less than –22° F (–30° C) and the oil temperature sensor reading indicates an engine block heater has not been used. An externallypowered electric engine block heater is available as optional equipment or from your authorized studio.
218 STARTING AND OPERATING If Engine Fails To Start WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! • Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
STARTING AND OPERATING 219 MANUAL TRANSMISSION Five-Speed Manual Transmission WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should always be applied when the driver is not in the vehicle, especially on an incline. 5 Shift Lever Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal.
220 STARTING AND OPERATING Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, fifth gear is recommended.
STARTING AND OPERATING 221 Downshifting DRIVING ON SLIPPERY SURFACES Proper downshifting will improve fuel economy and Acceleration prolong engine life. Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the driving wheels to pull CAUTION! erratically to the right or left.
222 STARTING AND OPERATING Traction DRIVING THROUGH WATER When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. 1.
STARTING AND OPERATING 223 Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
224 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 225 If the Steering icon is displayed and the “POWER STEER- NOTE: ING SYSTEM OVER TEMP” message is displayed on the • Even if the power steering assistance is no longer EVIC screen, they indicate that extreme steering maneuoperational, it is still possible to steer the vehicle. vers may have occurred which caused an over temperature Under these conditions there will be a substantial condition in the power steering system.
226 STARTING AND OPERATING The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, press the center button, then lower the lever completely. When the parking brake is applied with the ignition switch in the MAR (ACC/ON/RUN) position, the Brake Warning Light in the instrument cluster will illuminate.
STARTING AND OPERATING 227 WARNING! (Continued) • Do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the MAR (ACC/ON/RUN) position. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury.
228 STARTING AND OPERATING 1. To activate the Sport mode, press the SPORT button. BRAKE SYSTEM In the event power assist is lost for any reason (for example; repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly more than that required with the power system operating.
STARTING AND OPERATING 229 The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. The ABS includes an amber ABS Warning Light. When the light is illuminated, the ABS is not functioning. The system reverts to standard non-anti-lock brakes. Turning the ignition Off and On again may reset the ABS if the fault detected was only momentary.
230 STARTING AND OPERATING When you are in a severe braking condition involving the use of the ABS, you will experience some pedal drop as the vehicle comes to a stop. This is the result of the system reverting to the base brake system. Anti-Lock Brake System (ABS) This system aids the driver in maintaining vehicle control under adverse braking conditions.
STARTING AND OPERATING 231 benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. WARNING! • The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
232 STARTING AND OPERATING period of time after the driver takes his foot off the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to the amount of throttle applied as the vehicle starts to move in the intended direction of travel. HSA Activation Criteria WARNING! There may be situations on minor hills (i.e., less than 2.
STARTING AND OPERATING 233 Electronic Stability Control (ESC) This system enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteering or understeering condition. Engine power may also be reduced to help the vehicle maintain the desired path.
234 STARTING AND OPERATING WARNING! The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent all accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent accidents resulting from loss of vehicle control due to inappropriate driver input for the conditions.
STARTING AND OPERATING 235 WARNING! WARNING! When in “Partial Off” mode, the TCS functionality of ESC (except for the limited slip feature described in the TCS section) has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the engine power reduction of TCS is disabled, and the enhanced vehicle stability offered by the ECS system is reduced. In the ESC “Full Off” mode, the engine torque reduction and stability features are cancelled.
236 STARTING AND OPERATING driven several miles (kilometers) at speeds greater than NOTE: 30 mph (48 km/h), see your authorized studio as soon as • The ESC Activation/Malfunction Indicator Light and possible to have the problem diagnosed and corrected. the ESC OFF Indicator Light come on momentarily The ESC Activation/Malfunction Indicator Light (located each time the ignition switch is turned ON.
STARTING AND OPERATING 237 TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
238 STARTING AND OPERATING Tires designed to this standard have the letter “T” or • High flotation tire sizing is based on U.S. design “S”molded into the sidewall preceding the size desigstandards and it begins with the tire diameter molded nation. Example: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
STARTING AND OPERATING 239 EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
240 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 241 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
242 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
STARTING AND OPERATING 243 To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. Loading The combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
244 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • The following table shows examples on how to calcu“XXX” amount equals 1,400 lbs (635 kg) and there will late total load, cargo/luggage, and towing capacities be five 150 lb (68 kg) passengers in your vehicle, the of your vehicle with varying seating configurations amount of available cargo and luggage load capacity and number and size of occupants.
STARTING AND OPERATING 245 5
246 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 247 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. The pressure should be checked and adjusted as well as inspected for signs of tire wear or visible damage, at least once a month.
248 STARTING AND OPERATING Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
STARTING AND OPERATING 249 WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious collision. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision.
250 STARTING AND OPERATING If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Summer Or Three Season Tires – If Equipped Summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. Summer tires will not contain the all season designation or mountain/snowflake symbol on the tire sidewall.
STARTING AND OPERATING 251 If your vehicle is not equipped with an original equipment tire and wheel as a spare, a non-matching temporary emergency use spare may be equipped with your vehicle. Temporary use spares are engineered to be used only with your vehicle. Your vehicle may be equipped with one of the following types of non-matching temporary use spares; compact, full size, or limited-use. Do not install more than one non-matching temporary use spare tire/wheel on the vehicle at any given time.
252 STARTING AND OPERATING These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. replaced.
STARTING AND OPERATING 253 WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
254 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
STARTING AND OPERATING 255 These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with Due to limited clearance, tire chains or traction devices aggressive tread designs such as those on all season type are not recommended. tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a CAUTION! smooth, quiet ride.
256 STARTING AND OPERATING The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire Rotation TIRE PRESSURE MONITORING SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12° F (6.5° C).
STARTING AND OPERATING 257 The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold tire pressure on the placard.
258 STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
STARTING AND OPERATING 259 • Seasonal temperature changes will affect tire pressure, The TPMS consists of the following components: and the TPMS will monitor the actual tire pressure in • Receiver Module the tire. • Four Tire Pressure Monitoring Sensors Base System • Tire Pressure Monitoring Telltale Light This is the TPMS warning indicator located in the Tire Pressure Monitoring Low Pressure Warnings instrument cluster.
260 STARTING AND OPERATING Check TPMS Warnings 3. Snow or ice around the wheels or wheel housings. The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and remain on solid when a system fault is detected, and the “Tire Pressure Monitoring Unavailable” text message will display. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The Tire Pressure Monitoring Telltale Light will turn off when the fault condition no longer exists.
STARTING AND OPERATING 261 3. However, after driving the vehicle for up to 20 min- 5.
262 STARTING AND OPERATING General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: FUEL REQUIREMENTS This engine is designed to meet all emission regulations and provide satisfactory fuel economy and performance when using high-quality unleaded “regular” gaso• This device may not cause harmful interference. line having an octane rating of 87.
STARTING AND OPERATING 263 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. Do not use gasoline containing Methanol or E-85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
264 STARTING AND OPERATING If a Non-FFV vehicle is inadvertently fueled with E-85 MMT In Gasoline fuel, the engine will have some or all of these symptoms: MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline • operate in a lean mode blended with MMT provides no performance advantage • OBD II “Malfunction Indicator Light” on beyond gasoline of the same octane number without MMT.
STARTING AND OPERATING 265 Materials Added To Fuel CAUTION! (Continued) All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
266 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 267 CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
268 STARTING AND OPERATING WARNING! (Continued) Loose Fuel Filler Cap Message After fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged. If the system detects a malfunction, the “gASCAP” message will display in the odometer display. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off.
STARTING AND OPERATING 269 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Flat Tow Dolly Tow On Trailer Wheels OFF the Ground NONE Front Rear ALL NOTE: Vehicles equipped with manual transmissions may be recreationally towed (flat towed) at any legal highway speed, for any distance, if the manual transmission is in NEUTRAL. NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .272 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .284 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .272 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . .286 䡵 TIREFIT KIT — IF EQUIPPED . . . . . . . . . . . . .273 䡵 JUMP-STARTING PROCEDURE . . . . . . . . . . . .290 ▫ TIREFIT Storage . . . . . . . . . . . . . . . . . . . . . .274 ▫ Preparations For Jump-Start . . . . . . . . . . . . . .
272 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning • On the highways — slow down. flashers.
WHAT TO DO IN EMERGENCIES 273 CAUTION! WARNING! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off immediately and call for service.
274 WHAT TO DO IN EMERGENCIES TIREFIT Storage TIREFIT Kit Components And Operation The TIREFIT kit is located under the front driver’s seat. TIREFIT Kit Location TIREFIT Components 1. Sealant Bottle 2. Deflation Button 3.
WHAT TO DO IN EMERGENCIES 275 4. Power Button 5. Mode Select Knob 6. Sealant Hose (Clear) 7. Air Pump Hose (Black) 8. Power Plug • When the TIREFIT sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the TIREFIT kit.
276 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the TIREFIT kit. • Do not use TIREFIT or drive the vehicle under the following circumstances: – If the puncture in the tire tread is approximately 1/4 in. (6 mm) or larger. – If the tire has any sidewall damage. – If the tire has any damage from driving with extremely low tire pressure.
WHAT TO DO IN EMERGENCIES 277 WARNING! (Continued) • TIREFIT Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep TIREFIT out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. Sealing A Tire With TIREFIT (A) Whenever You Stop To Use TIREFIT: 1. Pull over to a safe location and turn on the vehicle’s Hazard Warning flashers. 2.
278 WHAT TO DO IN EMERGENCIES (B) Setting Up To Use TIREFIT: (C) Injecting TIREFIT Sealant Into The Deflated Tire: 1. Turn the Mode Select Knob (5) to the Sealant Mode • Always start the engine before turning ON the TIREposition. FIT kit. 2. Uncoil the Sealant Hose (6) and then remove the cap NOTE: Manual transmission vehicles must have the from the fitting at the end of the hose. parking brake engaged and the shift lever in NEUTRAL. 3.
WHAT TO DO IN EMERGENCIES 279 If the sealant (white fluid) does not flow within 0 – If the sealant (white fluid) does flow through the 10 seconds through the Sealant Hose (6): Sealant Hose (6): 1. Press the Power Button (4) to turn Off the TIREFIT kit. 1. Continue to operate the pump until sealant is no Disconnect the Sealant Hose (6) from the valve stem. longer flowing through hose (typically takes 30 Make sure the valve stem is free of debris. Reconnect 70 seconds).
280 WHAT TO DO IN EMERGENCIES If the tire does not inflate to at least 26 psi (1.8 Bar) 3. Immediately disconnect the Sealant Hose (6) from the pressure within 15 minutes: valve stem, reinstall the cap on the fitting at the end of the hose, and place the TIREFIT kit in the vehicle • The tire is too badly damaged. Do not attempt to drive storage location. Quickly proceed to (D) “Drive Vethe vehicle further. Call for assistance. hicle”.
WHAT TO DO IN EMERGENCIES 281 (D) Drive Vehicle: (E) After Driving: Immediately after injecting sealant and inflating the tire, Pull over to a safe location. Refer to “Whenever You Stop drive the vehicle 5 miles (8 km) or 10 minutes to ensure to Use TIREFIT” before continuing. distribution of the TIREFIT Sealant within the tire. Do not 1. Turn the Mode Select Knob (5) to the Air Mode exceed 55 mph (88 km/h). position. WARNING! TIREFIT is not a permanent flat tire repair.
282 WHAT TO DO IN EMERGENCIES 5. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized studio as soon as possible. 1. Press the Power Button (4) to turn on TIREFIT and Refer to “(F) Sealant Bottle and Hose Replacement.” inflate the tire to the pressure indicated on the tire and loading information label on the driver-side door NOTE: When having the tire serviced, advise the authorized studio or service center that the tire has been sealed opening. using the TIREFIT service kit.
WHAT TO DO IN EMERGENCIES 283 5. Position the new Sealant Bottle (1) in the housing so JACKING AND TIRE CHANGING — IF EQUIPPED that the Sealant Hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the WARNING! housing. An audible click will be heard indicating the • Do not attempt to change a tire on the side of the bottle is locked into place. vehicle close to moving traffic. Pull far enough off 6.
284 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location The jack and jack wrench tool are stowed in a bag under the front driver’s seat. Jack And Jack-Handle Location Preparations For Jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas.
WHAT TO DO IN EMERGENCIES 285 WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flashers. 3. Set the parking brake. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel.
286 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flashers. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
WHAT TO DO IN EMERGENCIES 287 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the scissors jack and tool bag from under the driver’s seat. 2. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the wheel is still on the ground. NOTE: There are front and rear jacking locations on each side of the body (as indicated by the triangular lift point symbol on the sill molding).
288 WHAT TO DO IN EMERGENCIES 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Rear Jacking Location Do not raise the vehicle until you are sure the jack is securely engaged.
WHAT TO DO IN EMERGENCIES 289 WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. To avoid the risk of forcing the vehicle off the jack, do not fully tighten the wheel bolts until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 4. Using the swivel wrench, raise the vehicle by turning 6.
290 WHAT TO DO IN EMERGENCIES 7. Lower the vehicle by turning the jack screw to the left. JUMP-STARTING PROCEDURE 8. Finish tightening the bolts. Push down on the wrench while tightening the wheel bolts. Alternate bolts until each bolt has been tightened twice. The correct wheel bolt torque is 63 ft lbs (85 N·m) for steel wheels and 75 ft lbs (100 N·m) for aluminum wheels.
WHAT TO DO IN EMERGENCIES 291 CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. Preparations For Jump-Start The battery in your vehicle is located on the left side of the engine compartment.
292 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
WHAT TO DO IN EMERGENCIES 293 Jump-Starting Procedure WARNING! Failure to follow this procedure could result in personal injury or property damage due to battery explosion. CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2.
294 WHAT TO DO IN EMERGENCIES 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the engine ground (-) of the vehicle with the discharged battery.
WHAT TO DO IN EMERGENCIES 295 CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.
296 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed.
WHAT TO DO IN EMERGENCIES 297 Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws regarding vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 1.4L TURBO . . . .301 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . .309 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .302 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .310 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . .302 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . .314 䡵 REPLACEMENT PARTS . . . . . . . . . . . . . . . . . .304 䡵 DEALER SERVICE . . . . . . . . . .
300 MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .327 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 ▫ Front Fog Lamps . . . . . . . . . . . . . . . . . . . . . .341 ▫ Front/Rear Side Marker Lamps. . . . . . . . . . . .341 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . .333 ▫ Rear Tail, Stop, Backup And Turn Signal Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 301 ENGINE COMPARTMENT — 1.
302 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 303 Indicator Light (MIL)” is functioning and is not on when 3. As soon as you turn the ignition switch to the ON the engine is running, and that the OBD II system is position, you will see the MIL symbol come on as part ready for testing. of a normal bulb check. Normally, the OBD II system will be ready. The OBD II 4.
304 MAINTAINING YOUR VEHICLE you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update. A recheck with the above test routine may then indicate that the system is now ready. DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.
MAINTAINING YOUR VEHICLE 305 WARNING! CAUTION! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance.
306 MAINTAINING YOUR VEHICLE Engine Oil Checking Oil Level CAUTION! Do not overfill the engine with oil. Overfilling the To assure proper engine lubrication, the engine oil must engine with oil will cause oil aeration, which can be maintained at the correct level. Check the oil level at lead to loss of oil pressure and an increase in oil regular intervals, such as every fuel stop. The best time to temperature.
MAINTAINING YOUR VEHICLE 307 Engine Oil Selection For best performance and maximum protection for turbocharged engines under all types of operating conditions, the manufacturer recommends synthetic engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-10896. CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty.
308 MAINTAINING YOUR VEHICLE Materials Added To Engine Oil Engine Oil Filter Selection Do not add any supplemental materials, other than leak detection dyes, to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives. This manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably.
MAINTAINING YOUR VEHICLE 309 WARNING! (Continued) WARNING! for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps.
310 MAINTAINING YOUR VEHICLE WARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case.
MAINTAINING YOUR VEHICLE 311 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
312 MAINTAINING YOUR VEHICLE The A/C air filter is located in the fresh air inlet on the 2. Pull the console closeout cover rearward to disengage lower right of center console. Perform the following the front retaining tab and remove the cover. procedure to replace the filter: 1. Remove the T20 Torx screw that secures the passenger side console closeout cover.
MAINTAINING YOUR VEHICLE 313 3. Remove the two 5.5mm screws (1 and 2) that secure the particulate air filter cover to the HVAC housing. A/C Air Filter 5. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal. 4. Remove the A/C air filter by pulling it straight out of the housing. Take note of the air filter position indicators.
314 MAINTAINING YOUR VEHICLE CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function.
MAINTAINING YOUR VEHICLE 315 Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use.
316 MAINTAINING YOUR VEHICLE 3. Grab the bottom of the wiper blade and rotate it 4. Install the wiper blade pivot pin into the wiper blade forward to unsnap the blade pivot pin from the wiper holder at the end of the wiper arm, and firmly press blade holder. the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place.
MAINTAINING YOUR VEHICLE 317 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
318 MAINTAINING YOUR VEHICLE CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 319 To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
320 MAINTAINING YOUR VEHICLE accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Cooling System – Drain, Flush, And Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution.
MAINTAINING YOUR VEHICLE 321 CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
322 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types is not recommended and can result in cooling system damage. Drain, flush, and refill as soon as possible to avoid damage if coolant types are mixed in an emergency.
MAINTAINING YOUR VEHICLE 323 As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a Used ethylene glycol-based engine coolant (antifreeze) is month. a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal When additional engine coolant (antifreeze) is needed to rules for your community.
324 MAINTAINING YOUR VEHICLE If an examination of your engine compartment shows no • Make sure that the coolant expansion bottle overflow evidence of radiator or hose leaks, the vehicle may be hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. • Keep the front of the radiator clean. If your vehicle is • Do not overfill the coolant expansion bottle. equipped with air conditioning, keep the front of the condenser clean.
MAINTAINING YOUR VEHICLE 325 WARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. Riding the brakes may also reduce braking capacity in an emergency. brake pads wear. The brake fluid level should be checked when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed.
326 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir.
MAINTAINING YOUR VEHICLE 327 CAUTION! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmission. Manual Transmission Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless lubricant has become contaminated with water.
328 MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will Washing have an adverse effect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your vebody protection. hicle in the shade using MOPAR威 Car Wash, or a mild car wash soap, and rinse the panels completely with The following maintenance recommendations will enable clear water. you to obtain maximum benefit from the corrosion resistance built into your vehicle.
MAINTAINING YOUR VEHICLE 329 CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
330 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care Stain Repel Fabric Cleaning Procedure – If Equipped • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly Stain Repel seats may be cleaned in the following manner: with a mild soap and water to prevent corrosion. • Remove as much of the stain as possible by blotting with a clean, dry towel. • To remove heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner.
MAINTAINING YOUR VEHICLE 331 Interior Care Use MOPAR威 Total Clean to clean fabric upholstery and carpeting. Use MOPAR威 Total Clean to clean vinyl upholstery. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. MOPAR威 Total Clean is specifically recommended for Cleaning Headlights leather upholstery.
332 MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instrument that may scratch the elements.
MAINTAINING YOUR VEHICLE 333 Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Dry with a soft cloth. Replace the belts if they appear frayed or worn or if the buckles do not work properly.
334 MAINTAINING YOUR VEHICLE 1 Vehicle Fuse Number F12 2 F32 Cavity 3 F53 4 F38 5 F36 Mini Fuse 7.5 Amp Brown 5 Amp Tan 5 Amp Tan 20 Amp Yellow 10 Amp Red Description Right Low Beam Front and Rear Ceiling Lights Trunk and Door Courtesy Lights Instrument Panel Node Central Door Locking Diagnostic Socket, Car Radio, Climate Control System 6 Vehicle Fuse Number F43 7 F48 8 F13 9 F50 10 F51 Cavity Mini Fuse 20 Amp Yellow 20 Amp Yellow 7.5 Amp Brown 7.
MAINTAINING YOUR VEHICLE 335 Underhood Fuses 11 Vehicle Fuse Number F37 12 F49 5 Amp Tan 13 F31 14 F47 5 Amp Tan 20 Amp Yellow Cavity Mini Fuse 5 Amp Tan Description Stop Light Switch, Instrument Panel Node Exterior Mirror, GPS, Electric Mirror, Parking Sensor Ignition, Climate Control Driver Power Window The Front Distribution Unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover.
336 MAINTAINING YOUR VEHICLE The ID number of the electrical component corresponding to each fuse can be found on the back of the cover.
MAINTAINING YOUR VEHICLE 337 Cavity F14 F15 F16 F17 F17 F18 F18 Maxi Fuse Mini Fuse 5 Amp Tan 15 Amp Blue 7.5 Amp Brown 25 Amp White 15 Amp Blue 15 Amp Blue 5 Amp Tan Description Cavity High beam (Shutter) Cigar Lighter F19 Transmission F21 Powertrain (Multiair – If Equipped) Powertrain F23 Powertrain F30 Powertrain (Multiair – If Equipped) F82 Maxi Fuse Mini Fuse 7.5 Amp Brown 15 Amp Blue 15 Amp Blue 20 Amp Yellow 7.
338 MAINTAINING YOUR VEHICLE Cavity F84 F85 F87 F90 Maxi Fuse VEHICLE STORAGE Mini Fuse 10 Amp Red 15 Amp Blue 5 Amp Tan 5 Amp Tan Description Transmission Rear Defroster, Heated Mirrors Lights Heated Mirrors If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e.
MAINTAINING YOUR VEHICLE 339 REPLACEMENT BULBS Interior Bulbs Overhead Lamp Courtesy Lamp Bulb Number C5W W5W Exterior Bulbs Front Low and High Beam Headlamp Front Parking/Daytime Running Lamps Front Fog Lamps Front Side Marker Lamps Front Turn Signal Lamps Bulb Number HIR2 W21/5W H11 W3W WY21W Side Direction Lamps Rear Turn Signal Lamps Rear Side Marker Lamps Rear Tail and Stop Lamps Rear Backup Lamps Center High Mounted Stop Lamp License Plate Lamps Bulb Number W5W PY21W W3W PY21W/5W W16W W5W LED (S
340 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlamps 1. Remove the plastic cap from the back of the headlamp housing. 2. Rotate the bulb counter-clockwise. 3. Remove the bulb and replace as needed. 4. Install the bulb and rotate clockwise to lock in place. 5. Reinstall the plastic cap. Front Turn Signal, Parking And Daytime Running Lamps 1. Turn the steering wheel completely to the left or right. 2. Open the wheel housing access door. 3. Remove the plastic cap from the back of the lamp housing. 4.
MAINTAINING YOUR VEHICLE 341 6. Install the bulb into socket, and rotate bulb/socket Rear Tail, Stop, Backup And Turn Signal Lamps clockwise into lamp locking it in place. 1. Open the liftgate. 7. Reinstall the plastic cap. 2. Remove the two screws and remove the tail lamp Front Fog Lamps assembly. To replace the front fog lights, see your authorized studio. Front/Rear Side Marker Lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. 2.
342 MAINTAINING YOUR VEHICLE 4. Remove the tail, stop, or turn signal bulbs by pushing 3. them slightly and turning counter-clockwise. 4. 5. Remove the backup lamp bulb by pulling straight out. 5. 6. Replace lamps as required and reinstall lamp. Center High Mounted Stop Lamp (CHMSL) Disconnect the electric connector. Press the retaining device and open the bulb holder. Remove the snap-fitted bulb to be replaced and replace it. 6. Close the back cap locking it properly. 1.
MAINTAINING YOUR VEHICLE 343 FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 1.4 Liter Turbo Engine Cooling System 1.4 Liter Turbo Engine (MOPAR威 Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula or equivalent) U.S. 10.5 Gallons Metric 40 Liters 4 Quarts 3.8 Liters 4.6 Quarts 4.
344 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Chrysler Material Standard MS-12106. Use API Certified SAE 5W-40 Full Synthetic Engine Oil, meeting the requirements of Chrysler Material Standard MS-10896.
MAINTAINING YOUR VEHICLE 345 Chassis Component Manual Transmission Brake Master Cylinder Fluid, Lubricant, or Genuine Part MOPAR威 C635 DDCT/MTX Transmission Fluid MOPAR威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
M A I N T E N A ▫ Maintenance Chart. . . . . . . . . . . . . . . . . . . . .350 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 348 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Once A Month Or Before A Long Trip: Your vehicle is equipped with an automatic oil change • Check engine oil level indicator system. The oil change indicator system will • Check windshield washer fluid level remind you that it is time to take your vehicle in for scheduled maintenance.
MAINTENANCE SCHEDULES 349 M Required Maintenance Intervals. Refer to the Maintenance Schedules on the following pages for required maintenance. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • Inspect battery and clean and tighten terminals as required.
8 Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary. Inspect the brake linings, parking brake function. Additional Maintenance Replace cabin/air conditioning filter.
Clean and lube sun roof tracks. Replace engine air filter. Replace the spark plugs. ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Inspect and replace PCV valve if necessary. Replace the timing belt.
M 352 MAINTENANCE SCHEDULES A I WARNING! N T E • You can be badly injured working on or around a motor vehicle. Do only service work for which you N A have the knowledge and the right equipment. If you N have any doubt about your ability to perform a C service job, take your vehicle to a competent meE S C H E D U L E S 8 chanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .357 YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .354 䡵 REPORTING SAFETY DEFECTS . . . . . . . . . . . .357 ▫ Prepare For The Appointment. . . . . . . . . . . . .354 ▫ In The 50 United States And Washington, D.C.. . . . . . . . . . . . . . . . . . . . . .357 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .354 ▫ Be Reasonable With Requests . . . . . . .
354 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized studio, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
IF YOU NEED CONSUMER ASSISTANCE 355 facilities, factory-trained technicians, special tools, and • Authorized studio name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized studio service manager first. Most matters can be re- FIAT Customer Center solved with this process. P.O.
356 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract.
IF YOU NEED CONSUMER ASSISTANCE 357 WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
358 IF YOU NEED CONSUMER ASSISTANCE In Canada Service Manuals If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately. Canadian customers who wish to report a safety defect to the Canadian government should contact Transport Canada, Motor Vehicle Defect Investigations and Recalls at 1-800-333-0510 or go to http://www.tc.gc.
IF YOU NEED CONSUMER ASSISTANCE 359 Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FIAT Group Automobiles vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. • Call toll free at: 1–800–890–4038 (U.S.) 1–800–387–1143 (Canada) Or • Visit us on the Worldwide Web at: www.techauthority.
360 IF YOU NEED CONSUMER ASSISTANCE significantly from the norm due to variations in driving Temperature Grades habits, service practices, and differences in road charac- The temperature grades are A (the highest), B, and C, teristics and climate. representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under Traction Grades controlled conditions on a specified indoor laboratory The Traction grades, from highest to lowest, are AA, A, B, test wheel.
IF YOU NEED CONSUMER ASSISTANCE 361 WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
364 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .321 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .316 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .265 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .49 Airbag Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 365 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . .225 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . .228 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . .228 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . .325 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . .
366 INDEX Coolant (Antifreeze) . . . . . . . . . . . Cooling System. . . . . . . . . . . . . . . Adding Coolant (Antifreeze) . . . Coolant Level . . . . . . . . . . . . . Disposal of Used Coolant . . . . . Drain, Flush, and Refill . . . . . . Inspection . . . . . . . . . . . . . . . . Points to Remember . . . . . . . . . Pressure Cap . . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Corrosion Protection . . . . . . . . . . . Cruise Light . . . . . . . . . . . . . . . . . Cupholders . . . . . .
INDEX 367 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .283 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . .290 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .296 Emission Control System Maintenance . . . . . . . . . .302 Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .308 Break-In Recommendations . . . . . . . . . . . . . . . .74 Checking Oil Level . . . . . . . . . . . . . . . . . . . . .306 Compartment . . . . . . . . . . . .
368 INDEX Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Fluids, Lubricants and Genuine Parts . . . . . . . . . . .344 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . . .294 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 369 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .331 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . .141 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Heated Mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Heated Seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
370 INDEX Malfunction Indicator (Check Engine) . . . . . . . .146 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . .145 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . . .262 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . .142 Leaks, Fluid . . . . .
INDEX 371 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . . .314 Multi-Function Control Lever . . . . . . . . . . . . . . . . .106 Maintenance Free Battery. . . . . . . . . . . . . . . . . . . .309 Maintenance, General . . . . . . . . . . . . . . . . . . . . . .305 Maintenance Procedures . . . . . . . . . . . . . . . . . . . .305 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . .348 Malfunction Indicator Light (Check Engine). . . . . . .146 Manual, Service . . . . . . . . . .
372 INDEX Recommendation . . . . . . . . . . . . . . . . . . . . . . .307 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .307 Oil Filter, Selection . . . . . . . . . . . . . . . . . . . . . . . .308 Onboard Diagnostic System . . . . . . . . . . . . . . . . . .302 Operating Precautions . . . . . . . . . . . . . . . . . . . . . .302 Operator Manual (Owner’s Manual) . . . . . . . . . . . . .5 Overheating, Engine . . . . . . . . . . . . . . . . . . . . . . .
INDEX 373 Remote Sound System (Radio) Controls . . . . . . . . .195 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . .339 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . .14 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . .304 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . . .253 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . .357 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Rotation, Tires . . .
374 INDEX Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . . .255 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 Specifications Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .307 Speed Control (Cruise Control). . . . . . . . . . .
INDEX 375 General Information . . . . . . . . . High Speed . . . . . . . . . . . . . . . Inflation Pressures . . . . . . . . . . Jacking . . . . . . . . . . . . . . . . . . Life of Tires . . . . . . . . . . . . . . . Load Capacity . . . . . . . . . . . . . Pressure Monitor System (TPMS) Pressure Warning Light . . . . . . Quality Grading . . . . . . . . . . . Radial . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . Rotation . . . . . . . . . . . . . . . . . Safety . . . . . . . .
376 INDEX Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . .262 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .328 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . . .32 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . .222 Vehicle Identification Number (VIN) . . . . . . . . . . . . .7 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . .330 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2012 500 2012 OWNER’S MANUAL Chrysler Group LLC 13FX24-126-AC 3rd Edition 500 Printed in U.S.A. 872214.ps 12FF500-126-AA Fiat 1" gutter 10/04/2010 11:37:45 2012 500 2012 OWNER’S MANUAL Chrysler Group LLC 12FF500-126-AA First Edition Printed in U.S.A.
