ENGLISH The data contained in this publication is intended merely as a guide. FIAT reserves the right to modify the models and versions described in this booklet at any time for technical and commercial reasons. If you have any further questions please consult your FIAT dealer. Printed in recycled paper without chlorine.
WHY CHOOSING GENUINE PARTS We really know your car because we invented, designed and built it: we really know every single detail. At Fiat Service authorised workshops you can find technicians directly trained by us, offering quality and professionalism for all service operations. Fiat workshops are always close to you for the regular servicing operations, season checks and practical recommendations by our experts.
HOW TO RECOGNIZE GENUINE PARTS All our Genuine Parts undergo rigorous testing, both in design and build stages, by specialists who check the use of cutting-edge materials and test their reliability. This guarantees performance and safety in the long term for both you and the passengers in your automobile. Always insist on a Genuine Part and check that it has been used.
Dear Customer, Thank you for choosing Fiat and congratulations on your choice of a Fiat Freemont. We have written this handbook to help you get to know all your car and use it in the best possible way. You should read it right through before taking to the road for the first time. You will find information, tips and important warnings regarding the driving of your car to help you get the most from the technological features of your Fiat.
KNOWING YOUR VEHICLE INTRODUCTION Congratulations on selecting your new FIAT vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Before you start to drive this vehicle, read this Owner's Manual and all the supplements. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, and transmission shifting. Learn how your vehicle handles on different road surfaces.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 2 IMPORTANT NOTICE ALL MATERIAL CONTAINED IN THIS PUBLICATION IS BASED ON THE LATEST INFORMATION AVAILABLE AT TIME OF PUBLICATION APPROVAL. THE RIGHT IS RESERVED TO PUBLISH REVISIONS AT ANY TIME.
changes to your vehicle that do not comply with the manufacturers specifications. Original parts and accessories and other products approved by the manufacturer, including qualified advice, are available at your authorized dealer. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factorytrained technicians and genuine parts, and is interested in your satisfaction. Copyright © 2012 FIAT Group Automobiles S.p.A.
KNOWING YOUR VEHICLE SAFETY HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle's equipment. STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (fig.
VEHICLE MODIFICATIONS/ ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
KNOWING YOUR VEHICLE INSTRUMENT PANEL FEATURES (fig. 2) SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE (fig.
INSTRUMENTS (fig. 3) 1. Tachometer This gauge measures engine revolutions per minute (RPM x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 3. Fuel Gauge The fuel gauge shows the level of fuel in the tank when ignition switch is in the ON/RUN position. KNOWING YOUR VEHICLE SAFETY 2. Speedometer Shows the vehicle speed. STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 8 4. Coolant Temperature Gauge The temperature gauge indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operating satisfactorily. The gauge pointer will likely indicate a high temperature when driving in hot weather, up mountain grades, in heavy traffic, or when towing a trailer.
KEY FOB The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. The emergency key is also for locking the glove box. You can keep the emergency key with you when valet parking.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 10 door will cancel this feature. The time for this feature is programmable. Refer to “Uconnect Touch™ Settings” in “Knowing Your Vehicle” for further information. WARNING! • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the key fob from the ignition. When leaving the vehicle, always lock your vehicle.
SENTRY KEY® The Sentry Key® Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a Key Fob with Remote Keyless Entry (RKE) transmitter, a Keyless Ignition Node (KIN) and a RF receiver to prevent unauthorized vehicle operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle.
KNOWING YOUR VEHICLE NOTE: When having the Sentry Key® Immobilizer system serviced, bring all vehicle Key Fobs with you to the authorized dealer. SAFETY CUSTOMER KEY PROGRAMMING Programming Key Fobs or RKE transmitters may be performed at an authorized dealer.
If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go (for versions/markets, where provided)” under “Knowing Your Vehicle” for further information. TO LOCK THE DOORS AND LIFTGATE Press and release the LOCK button on the RKE transmitter to lock all doors and liftgate. The turn signal lights will flash to acknowledge the signal.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY 1. Remove the emergency key by sliding the mechanical latch on the back of the RKE transmitter sideways with your thumb and then pull the key out with your other hand. 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal. (fig. 7) 3.
VEHICLE SECURITY ALARM (for versions/markets, where provided) The Vehicle Security Alarm (VSA) system monitors the vehicle doors, hood, and liftgate for unauthorized entry and the ignition switch for unauthorized operation. If something triggers the alarm, the system will sound the horn intermittently, flash the headlights and taillights, and flash the Vehicle Security Light in the instrument cluster.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 16 NOTE: • The driver's door key cylinder and the liftgate button on the RKE transmitter cannot arm or disarm the Vehicle Security Alarm. • The Vehicle Security Alarm remains armed during power liftgate entry. Pressing the liftgate button will not disarm the Vehicle Security Alarm.
• Press LOCK on the interior power door lock switch with the driver and/or passenger door open. • Press the LOCK button on the exterior Passive Entry Door Handle with a valid Key Fob available in the same exterior zone (refer to "Keyless Enter-N-Go" in "Knowing Your Vehicle" for further information). • Press the LOCK button on the Remote Keyless Entry (RKE) transmitter. 3. If any doors are open, close them.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 18 SECURITY SYSTEM MANUAL OVERRIDE The system will not arm if you lock the doors using the manual door lock plunger. STEERING WHEEL LOCK (for versions/markets, where provided) Your vehicle may be equipped with a passive electronic steering wheel lock. This lock prevents steering the vehicle without the ignition key.
ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • Warning Message Displays • Turn Menu OFF The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. (fig. 8) The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: (fig. 9) This system allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 20 DOWN Button Press and release the DOWN button to scroll downward through the main menus and sub-menus. SELECT Button Press and release the SELECT button for access to main menus or sub-menus. Press and hold the SELECT button for two seconds to reset features. BACK Button Press the BACK button to scroll back to a previous menu or sub-menu.
The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left. When the appropriate conditions exist, the EVIC displays the following messages: • Turn Signal On (with a continuous warning chime if the vehicle is driven more than 1.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE EVIC WHITE TELLTALE LIGHTS This area will show reconfigurable white caution telltales. These telltales include: • Shift Lever Status — Automatic Transmission Only The shift lever status “P,R,N,D,L,5,4,3,2,1” are displayed indicating the shift lever position. Telltales “5,4,3,2,1” indicate the Autostick™ feature has been engaged and the gear selected is displayed.
Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition is first cycled ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle's non-essential electrical devices or increase engine speed (if at idle).
KNOWING YOUR VEHICLE Continuous driving with theTransmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.
Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the SELECT button. NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 26 Elapsed Time Shows the total elapsed time of travel since the last reset. Elapsed time will increment when the ignition is in the ON/RUN position. To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the SELECT button once to clear the resettable function.
Uconnect Touch™ SETTINGS HARD-KEYS Hard-Keys are located on the left and right side of the Uconnect Touch™ 4.3 screen. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), press the center of the control knob one or more times to select or change a setting (i.e., ON, OFF). shown on the following pages for each setting (fig. 11) (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 28 Display • Brightness (for versions/markets, where provided) Press the Brightness soft-key to change this display. When in this display you may select display brightness with the headlights on and the headlights off.
soft-key, adjust the hours and minutes using the up and down soft-keys, select AM or PM, select 12 hr or 24 hr followed by pressing the arrow back soft-key when all selections are complete. • Show Time Status (for versions/markets, where provided) Press the Show Time Status soft-key to change this display. When in this display you may turn on or shut off the digital clock in the status bar.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 30 • Headlights with Wipers (for versions/markets, where provided) Press the Headlights with Wipers soft-key to change this display. When this feature is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on.
doors will unlock on the first press of the RKE transmitter UNLOCK button. NOTE: If the vehicle is equipped with Keyless EnterN-Go (Passive Entry) and the EVIC is programmed to Unlock All Doors 1st Press, all doors will unlock no matter which Passive Entry equipped door handle is grasped. If Driver Door 1st Press is programmed, only the driver’s door will unlock when the driver’s door is grasped.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING Compass Settings • Variance (for versions/markets, where provided) Press the Variance soft-key to change this display. Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading.
• Calibration (for versions/markets, where provided) Press the Calibration key to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic and the EVIC will display CAL until the compass is calibrated.
KNOWING YOUR VEHICLE SAFETY CUSTOMER PROGRAMMABLE FEATURES — Uconnect Touch™ SYSTEM 8.4 SETTINGS In this mode the Uconnect Touch™ system allows you to access programmable features that may be equipped such as Display, Clock, Safety/Assistance, Lights, Doors & Locks, Auto-On Comfort , Engine Off Operation, Compass Settings, Audio and Phone/Bluetooth settings. STARTING AND DRIVING NOTE: Only one touchscreen area may be selected at a time. (fig.
Then, as you continue, the information will display in the selected language. • Units (for versions/markets, where provided) When in this display you may select to have the EVIC, odometer, and navigation system (for versions/ markets, where provided) changed between US and Metric units of measure. Press US or Metric followed by pressing the arrow back soft-key. Then, as you continue, the information will display in the selected units of measure.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 36 soft-key, select 12 hr or 24 hr followed by pressing the arrow back soft-key when all selections are complete. • Show Time in Status Bar (for versions/markets, where provided) When in this display you may turn on or shut off the digital clock in the status bar.
• Headlights with Wipers (for versions/markets, where provided) When this feature is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press the Headlights with Wipers soft-key, select On or Off followed by pressing the arrow back soft-key.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 38 • 1st Press of Key Fob Unlocks (for versions/markets, where provided) When Unlock Driver Door Only On 1st Press is selected, only the driver's door will unlock on the first press of the RKE transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger's doors.
properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading. NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod's, Mobile Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 40 • Perform Compass Calibration (for versions/markets, where provided) Press the Calibration key to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic and the EVIC will display CAL until the compass is calibrated.
SEATS Seats are a part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
For Vehicles Equipped With Uconnect Touch™ 4.3: Touch the CLIMATE hard-key (located on the left side of the Uconnect Touch™ display) to enter the climate control screen. Touch the “Driver” or “Passenger” seat softkey once to select HI-level heating. Touch the soft-key a second time to select LO-level heating. Touch the soft-key a third time to shut the heating elements OFF. (fig. 19) Touch the “Driver” or “Pass” seat soft-key (located on the Uconnect Touch™ display) once to select HI-level heating.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
RECLINER ADJUSTMENT The recline lever is located on the outboard side of the seat. To recline the seat, lean forward slightly, lift the lever, lean back to the desired position and release the lever. To return the seatback to its normal upright position, lean forward and lift the lever. Release the lever once the seatback is in the upright position. (fig. 21) WARNING! • Adjusting a seat while the vehicle is moving is dangerous.The sudden movement of the seat could cause you to lose control.
KNOWING YOUR VEHICLE Pull upward on the recline lever to fold or unfold the seat. SAFETY HEAD RESTRAINTS Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. STARTING AND DRIVING WARNING LIGHTS AND MESSAGES (fig.
be split in two halves, with the front half being soft foam and trim, the back half being decorative plastic. When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. Refer to “Occupant Restraints” in “Safety” for further information.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.These items may interfere with the operation of the Active Head Restraint in the event of a collision and could result in serious injury or death. • Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo.
WARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.The head restraints should be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. THIRD ROW PASSENGER SEATS (Seven Passenger Models) These head restraints are non-adjustable and nonremovable. However, you can fold them forward when they are not in use by passengers.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES To Fold The Seat 1. Locate the control lever on the lower outboard side of the seat. (fig. 28) 2. Place one hand on the seatback and apply a gentle pressure. 3. Lift the control lever with the other hand, allow the seatback to move forward slightly, and then release the lever. WARNING! To prevent personal injury or damage to objects, keep your head, arms, and objects out of the folding path of the seatback. 4.
Recliner Adjustment The recline lever is on the outboard side of the seat. To recline the seatback, lean back, lift the lever, position the seatback as desired, and then release the lever. To return the seatback to its normal upright position, lean back, lift the lever, lean forward, and then release the lever once the seatback is in the upright position. (fig. 30) WARNING! • Adjusting a seat while the vehicle is moving is dangerous.The sudden movement of the seat could cause you to lose control.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING Seatback/Armrest — Second Row Passenger Seat The latch release-loop is located at the top of the seatback/armrest. Pull the release-loop forward to release the latch and then downward to lower the seatback/armrest. (fig. 31) Raise the seatback/armrest and lock it in place when not in use, or when additional seating area is required. WARNING! Keep the latch clean and free of objects and be certain that the seatback/ armrest is locked securely into position.
WARNING! Do not drive the vehicle with the seat in this position, as it is only intended for entering and exiting the third row seats. Failure to follow this warning may result in personal injury. (fig. 32) Tip 'n Slide™ Control Lever To Unfold And Move The Second-Row Passenger Seat Rearward 1. Move the seatback rearward until it locks in place and then continue sliding the seat rearward on its tracks until it locks in place. 2. Push the seat cushion downward to lock it in place. 3.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 50/50 SPLIT THIRD-ROW PASSENGER SEATS WITH FOLD-FLAT FEATURE (Seven Passenger Models) To provide additional storage area, each third-row passenger seatback can be folded flat. This allows for extended cargo space and still maintains some rear seating room if needed.
WARNING! • Be certain that the seatback is locked securely into position. Otherwise, the seat will not provide the proper stability for passengers. An improperly latched seat could cause serious injury. • Do not allow a passenger to sit in a third row seat without having the head restraint unfolded and locked in place. Failure to follow this warning may result in personal injury to the passenger in the event of a collision.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your vehicle. Failure to follow this warning may result in serious injury or death. MIRRORS INSIDE DAY/NIGHT MIRROR A single ball joint mirror is provided in the vehicle.
AUTOMATIC DIMMING MIRROR (for versions/markets, where provided) This mirror automatically adjusts for headlight glare from vehicles behind you. This feature will be defaulted on, and only be disabled when the vehicle is moving in reverse. NOTE: This feature is disabled when the vehicle is moving in reverse. (fig. 38) To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES POWER MIRRORS The power mirror switch is located on the driver's door trim panel. (fig. 39) Models Without Express Window Feature Press the mirror select button marked L (left) or R (right) and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing.
ILLUMINATED VANITY MIRRORS (for versions/markets, where provided) An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward. The light will turn on automatically. Closing the mirror cover will turn off the light. (fig. 40) Sun Visor “Slide-On Rod” Feature (for versions/markets, where provided) This feature allows for additional flexibility in positioning the visor to block out the sun. 1. Fold down the sun visor. 2.
Soft-Keys Soft-keys are accessible on the Uconnect Touch™ system screen. (fig. 44) (fig. 45) KNOWING YOUR VEHICLE Button Descriptions (Applies To Both Hard-keys And Soft-keys) SAFETY 1. A/C Button Press and release to change the current Air Conditioning (A/C) setting; the indicator illuminates when A/C is ON. For versions/markets, where provided with ATC, performing this function will cause the automatic operation to switch into manual mode and the AUTO indicator will turn off.
3. Blower Control Blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation for versions/markets, where provided with ATC. The speeds can be selected using either hard-keys or softkeys as follows: (fig. 44) Uconnect Touch™ System 4.3 Manual Temperature Controls — Soft-Keys (fig. 45) Uconnect Touch™ System 8.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY 4. Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illuminates when this feature is ON. Performing this function will cause the ATC (for versions/markets, where provided) to switch into manual mode. The blower speed may increase when Defrost mode is selected. If the front defrost mode is turned off, the climate system will return the previous setting. 5.
8. Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF. 9. AUTO Operation Button (for versions/markets, where provided) Automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Performing this function will cause the ATC to switch between manual mode and automatic modes. Refer to “Automatic Operation” for more information. 10. Driver Temperature Control Down Button Provides the driver with independent temperature control.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 64 • Defrost Mode Air comes from the windshield and side window demist outlets. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. When the Defrost mode is selected, the blower level may increase. 13. SYNC Press the Sync soft-key to toggle the Sync feature On/Off.
Recirculation Control When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by pressing the Recirculation control button. The recirculation indicator will illuminate when this button is selected. Push the button a second time to turn off the Recirculation mode and allow outside air into the vehicle. NOTE: In cold weather, use of Recirculation mode may lead to excessive window fogging.
SAFETY The blower fan speed can be set to any fixed speed by adjusting the blower control. The fan will now operate at a fixed speed until additional speeds are selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the Auto mode. Rear Lock Pressing the Rear Temperature Lock soft-key on the Uconnect Touch™ screen, illuminates a lock symbol in the rear display. The rear temperature and air source are controlled from the front Uconnect Touch™ system.
The rear ATC is located in the headliner, near the center of the vehicle. (fig. 48) • Press the Rear Temperature Lock button on the Uconnect Touch™ screen. This turns off the Rear Temperature Lock icon in the rear temperature knob. • Rotate the Rear Blower, Rear Temperature and the Rear Mode Control knobs to suit your comfort needs. • ATC is selected by adjusting the rear blower knob counterclockwise to AUTO.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 68 REAR BLOWER CONTROL The rear blower control knob can be manually set to off, or any fixed blower speed, by rotating the knob from low to high. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle.
OPERATING TIPS NOTE: Refer to the chart at the end of this section for suggested control settings for various weather conditions. Summer Operation The engine cooling system in air-conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating. A solution of 50% ethylene glycol antifreeze coolant and 50% water is recommended. Refer to “Maintenance Procedures” in “Servicing And Care” for proper coolant selection.
KNOWING YOUR VEHICLE Manual Control Setting Suggestions For Various Weather Conditions (fig. 49) SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (fig.
LIGHTS HEADLIGHT SWITCH The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. (fig. 50) Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, parking light and instrument panel light operation.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS HEADLIGHT TIME DELAY This feature provides the safety of headlight illumination for up to 90 seconds when leaving your vehicle in an unlit area. NOTE: The Daytime Running Lights can be turned on and off using the Uconnect Touch™ System, refer to “Uconnect Touch™ Settings” in “Knowing Your Vehicle” for further information.
the headlight switch once and the front fog lights come on. Press the switch a second time and the rear fog lights will come on (front fog lights stay on). Press the switch a third time and the rear fog lights turn off (front fog stays on). Press the switch a fourth times and the front fog turns off. For vehicles without front fog, rear fog will activate on the first press. An indicator light in the instrument cluster illuminates when the fog lights are turned on.
KNOWING YOUR VEHICLE DIMMER CONTROLS The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. (fig. 52) INTERIOR LIGHT DEFEAT (OFF) Rotate the dimmer control to the extreme bottom off position. The interior lights will remain off when the doors are open. SAFETY Rotating the left dimmer control upward with the parking lights or headlights on will increase the brightness of the instrument panel lights.
0 1 Driver only, or driver and front passenger. All seating positions occupied, plus an evenly distributed load in the luggage compartment. The total weight of passengers and load does not exceed the maximum load capacity of the vehicle. 2 Driver, plus an evenly distributed load in the luggage compartment. The total weight of the driver and load does not exceed the maximum load capacity of the vehicle. Calculations based on a passenger weight of 75 kg.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the left side of the steering column. (fig. 53) The front wipers are operated by rotating a switch, located at the end of the lever. Refer to “Rear Window Features” for further information on using the rear window wiper/washer.
WINDSHIELD WIPER OPERATION Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation. (fig. 55) NOTE: The wipers will automatically return to the “park” position if you turn OFF the ignition switch while they are operating. The wipers will resume operation when you turn the ignition switch back to the ON position.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 78 If you activate the washer while the wiper control is in the OFF position, the wipers will operate for two or three wipe cycles and then turn OFF. WARNING! Sudden loss of visibility through the windshield could lead to a collision.You might not see other vehicles or other obstacles.
REAR WINDOW FEATURES REAR WINDOW WIPER/WASHER The rear window wiper/washer control is located on the right side of the steering column. (fig. 56) Rotate the switch upward to the first detent position for rear wiper operation. NOTE: The rear wiper operates in an intermittent mode only. Rotate the switch upward past the first detent position to activate the rear washer. The washer pump will continue to operate as long as the switch is held.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 80 • Turn the rear wiper off when driving through an automatic car wash. Damage to the rear wiper may result if the rear wiper switch is left in the on position. • In cold weather, always turn off the rear wiper switch and allow the rear wiper to return to the park position before turning off the engine.
ELECTRONIC SPEED CONTROL (for versions/markets, where provided) When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 40 km/h. The Electronic Speed Control buttons are located on the right side of the steering wheel. (fig. 58) NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 82 vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/ OFF button or turning the ignition switch OFF erases the set speed memory. TO ACCELERATE FOR PASSING Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, storage for sunglasses, an interior observation mirror and an optional power sunroof switch. (fig. 59) COURTESY/READING LIGHTS The overhead console has two courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING INTERIOR OBSERVATION MIRROR The convex interior observation mirror provides the driver and front seat passenger a wide field of view to conveniently view passengers sitting in the rear passenger seats. To use the interior observation mirror, press on the raised bars on the compartment door and release (the door will swing downward), then raise the door until it is almost closed and release.
HAZARD WARNING FLASHERS The Hazard Warning flasher switch is located in the instrument panel switch bank, above the climate controls. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flashers. STORAGE GLOVEBOX STORAGE The glovebox storage compartment is located on the passenger side of the instrument panel.
KNOWING YOUR VEHICLE FLOOR CONSOLE STORAGE An open storage area, or cubby bin, is located in the floor console. (fig. 64) SAFETY CENTER CONSOLE STORAGE There is a storage compartment located under the center console armrest. (fig. 65) STARTING AND DRIVING Pull upward on the release handle, located on the front of the lid, to open the storage compartment. (fig. 66) WARNING LIGHTS AND MESSAGES (fig. 65) Center Console IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (fig.
Sliding Armrest (for automatic transmission only) The center console armrest can also be slid rearward for easy access to the storage area. (fig. 67) WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE WARNING! Be certain that the seat cushion is locked securely into position before using the seat. Otherwise, the seat will not provide the proper stability for passengers. An improperly latched seat cushion could cause serious injury. SECOND-ROW PASSENGER SEAT TEMPORARY STORAGE BIN This is a temporary storage bin designed for use when the seatback/armrest is down.
ELECTRICAL POWER OUTLETS A 12 Volt (13 Amp) power outlet located in the center console below the radio. The power outlet has power available when the ignition switch in the ON/RUN or ACC position. (fig. 72) This power outlet will also operate a conventional cigar lighter unit. To preserve the heating element, do not hold the lighter in the heating position. KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES A second 12 Volt (13 Amp) power outlet is located inside the center console storage area. Power is available with the ignition switch in the ON/RUN, ACC or LOCK position. (fig. 73) A third fused 12 Volt power outlet is located on the back of the center console. This power outlet has power available when the ignition switch is in the LOCK, ON or ACC position. (fig.
• Do not exceed the maximum power of 160Watts (13 Amps) at 12Volts.If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • The power outlet on the bottom of the center console shares the fuse with the power outlet on the back of the console.The combined usage must not exceed 160 Watts (13 Amps) at 12 Volts. • Power outlets are designed for accessory plugs only.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE • Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.
When the armrest is folded flat the cupholders are in the back of the Head Restraint. The Head Restraint can be adjusted to better position the cupholders. (fig. 78) For vehicles equipped with third row seating, there are additional cupholders located in the trim panels. WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES POWER SUNROOF (for versions/markets, where provided) The power sunroof switch is located between the sun visors on the overhead console. (fig. 80) WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. CLOSING SUNROOF — MANUAL MODE To close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the switch is pushed and held forward again.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IGNITION OFF OPERATION The power sunroof switches remain active for up to approximately ten minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. NOTE: The delay time is programmable using the Uconnect Touch™ system. Refer to “Uconnect Touch™ Settings” for further information.
WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the Key Fob from the vehicle and lock your vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries or death. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 98 request of the customer. Please see your authorized dealer for service. Automatic Unlock Doors On Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 km/h. 3. The transmission is in NEUTRAL or PARK. 4.
2. Insert the tip of the emergency key (or alike) into the child lock control and rotate it to the LOCK position. (fig. 83) (fig. 84) 3. Repeat Steps 1 and 2 for the opposite rear door. NOTE: When the Child-Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. WARNING! Avoid trapping anyone in a vehicle in a collision.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES the window, and open the door with the outside door handle. To Disengage The Child-Protection Door Lock System 1. Open the rear door. 2. Insert the tip of the emergency key (or alike) into the child lock control and rotate it to the UNLOCK position. (fig. 85) 3. Repeat Steps 1 and 2 for the opposite rear door.
“Unlock Driver Door 1st Press” and “Unlock All Doors 1st Press”, refer to “Uconnect Touch™ Settings” in “Knowing Your Vehicle” for further information. To Unlock From The Passenger Side: With a valid Passive Entry RKE transmitter within 1.5 m of the passenger door handle, grab the front passenger door handle to unlock all four doors and the liftgate automatically.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES have been closed the vehicle checks the inside and outside of the vehicle for any valid Passive Entry RKE transmitters.
WINDOWS POWER WINDOWS The window controls on the driver's door trim panel control all of the door windows. (fig. 89) There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate when the ignition is in the ON/RUN or ACC position. NOTE: For vehicles equipped with the Uconnect Touch™, the power window switches will remain active for up to 10 minutes after the ignition is cycled to the OFF position.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS To close the window part way, pull the window switch up to the first detent and release it when you want the window to stop. NOTE: • If the window runs into any obstacle during Autoclosure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window.
WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (for versions/markets, where provided) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. These fumes could injure you and your passengers.Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the blower switch on the climate control is set at high speed. Do not use the recirculation mode.
CARGO MANAGEMENT SYSTEM FIVE PASSENGER SYSTEM FEATURES • A raised load floor that sits on top of a large built-in storage bin. • A tri-fold door built into the load floor that allows easy access to items in the built-in storage bin. • 60/40 split second-row passenger seats with fold flat feature, which allows for extended cargo space. Refer to “Seats” for further information. • An optional front passenger seat with fold flat feature, which extends cargo space even further.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY Cargo tie-downs are located on both rear trim panels. These tie-downs should be used to secure loads safely when the vehicle is moving. (fig. 94) WARNING! The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
To install the cover, position it in the vehicle so that the flat side of the housing faces upward. Then, insert either the left or the right spring-loaded post (located on the ends of the cover housing) into the left attachment point or the right attachment point (shown). (fig. 95) Insert the spring-loaded post on the opposite end of the cover housing into the attachment point on the opposite side of the vehicle. Grab the cover handle and pull it toward you.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. (fig. 97) 2. Outside of the vehicle, locate the safety latch lever near the center of the grille between the grille and hood opening. Push the safety latch lever to the right and then raise the hood. (fig. 98) Use the hood prop rod to secure the hood in the open position.
To prevent possible damage: • Before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips. • Do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! Be sure the hood is fully latched before driving your vehicle.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 112 • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 68 kg. Always distribute loads as evenly as possible and secure the load appropriately.
WARNING! • Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.You would not have your full braking capacity in an emergency. • Driving a vehicle with the “Brake SystemWarning Light” on is dangerous.A significant decrease in braking performance or vehicle stability during braking may occur.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 114 ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system commonly referred to as ESC. This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Traction Control System (TCS), Electronic Roll Mitigation (ERM), Electronic Stability Control (ESC), and Trailer Sway Control (TSC).
(Continued) • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 116 WARNING! BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
ELECTRONIC STABILITY CONTROL (ESC) This system enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for over-steering and under-steering the vehicle by applying the brake of the appropriate wheel. Engine power may also be reduced to help the vehicle maintain the desired path. The ESC uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY Partial Off The “ESC OFF” button is located in the switch bank above the climate control. To enter the “Partial Off” mode, momentarily press the “ESC OFF” button and the “ESC Activation/Malfunction Indicator Light” will illuminate. To turn the ESC on again, momentarily press the “ESC OFF” button and the “ESC Activation/ Malfunction Indicator Light” will turn off.
The “ESC Activation/Malfunction Indicator Light” (located in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light” also flashes when TCS is active. If the “ESC Activation/Malfunction Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 120 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 122 WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer's recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
tire pressure warning (Tire Pressure Monitoring Telltale Light) illuminates, you must increase the tire pressure to the recommended cold placard pressure in order for the Tire Pressure Monitoring Telltale Light to turn off. The system will automatically update and the Tire Pressure Monitoring Telltale Light will turn off once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minutes above 25 km/h in order for the TPMS to receive this information.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 124 NOTE: It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure.
5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically and the TPMS Telltale Light will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 25 km/h in order for the TPMS to receive this information.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 126 Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires.
3. After driving the vehicle for up to 20 minutes above 25 km/h, the TPMS Telltale Light will flash on and off for 75 seconds and then remain on solid. In addition, the EVIC will display a "CHECK TPM SYSTEM" message for three seconds and then display dashes (- -) in place of the pressure value. 4.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 128 GENERAL INFORMATION Transmitter and receivers operate on a carrier frequency of 433.92 MHz as required by EEC regulations. These devices must be certified to conform to specific regulations in each individual country.
PARKSENSE® SENSORS The four ParkSense® sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 30 cm up to 200 cm from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle. will change from slow, to fast, to continuous. (fig. 103) (fig. 104) (fig.
The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES (fig. 103) Slow Tone IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (fig. 104) (fig.
Rear Distance (cm) Audible Alert Chime Arcs Greater than 200 cm None None WARNING ALERTS 200-100 cm 100-65 cm Single 1/2Second Tone 3 Solid (Continuous) ENABLING AND DISABLING PARKSENSE® ParkSense® can be enabled and disabled using the Uconnect Touch™ System. The available choices are: Off, Sound Only, or Sound and Display. Refer to “Uconnect Touch™ Settings” for further information.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 132 PARKSENSE® SYSTEM USAGE PRECAUTIONS NOTE: • Ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the ParkSense® system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of ParkSense®. • When you turn ParkSense® off, the EVIC will display “PARK ASSIST SYSTEM OFF.
WARNING! • Drivers must be careful when backing up even when using the ParkSense® Rear Park Assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 134 WARNING! Drivers must be careful when backing up even when using the ParkView® Rear Back Up Camera.Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.
SOUND SYSTEMS Refer to your Uconnect Touch™ User Manual. NAVIGATION SYSTEM (for versions/markets, where provided) KNOWING YOUR VEHICLE Refer to your Uconnect Touch™ User Manual.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel. The left and righthand controls are rocker-type switches with a pushbutton in the center of each switch. Reach behind the steering wheel to access the switches. (fig. 106) RIGHT-HAND SWITCH FUNCTIONS • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume.
UCONNECT™ MULTIMEDIA VIDEO ENTERTAINMENT SYSTEM (VES)™ (for versions/markets, where provided) Your rear seat Video Entertainment System (VES)™ is designed to give your family years of enjoyment. You can play your favorite CDs or DVDs, listen to audio over the wireless headphones, or plug and play a variety of standard video games or audio devices. Please review this Owner's Manual to become familiar with its features and operation.
KNOWING YOUR VEHICLE SAFETY Remote Control Operation Quick Reference Chart This chart provides a quick reference of the remote control button functions for the different radio modes and menu screens.
Remote Control Button Right Arrow FF Left Arrow RW Enter Standard Screens AM/FM/ SAT– HDD– DISC/ AUX/AUX1/ MW/LW Audio Hard DVD AUX2 Disc Drive Tune Up* Next Next Fast For- Audio: Fast Channel* Channel ward Forward Video Fast Play: Forward Video SelecMenu: tion Right Tune Down* Previous Previous Fast ReAudio: Fast Channel* Channel wind Rewind Video Fast Play: Rewind Video SelecMenu: tion Left Show NuShow Nu- Not Avail- Show Nu- Audio: Show meric Entry meric En- able meric EnNuMenu* try Menu* try Menu me
KNOWING YOUR VEHICLE SAFETY Remote Control Button AM/FM/ MW/LW SAT– Audio Back Not Available Not Available Setup Not Available Not Available STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 140 Menu Not Available Not Available Standard Screens HDD– DISC/ AUX/AUX1/ Hard DVD AUX2 Disc Drive Not Avail- Not Avail- Audio: Not able able Available Video Not Play: Available Video Previous Menu: Menu Show/ Not Avail- Audio: Not Hide
Remote Control Button Play/Pause Stop Mute Slow AM/FM/ MW/LW SAT– Audio Not Available Not Available Not Available Not Available Not Available Not Available Standard Screens HDD– DISC/ AUX/AUX1/ Hard DVD AUX2 Disc Drive Not Avail- Pause if Audio: Pause if able playing, playing/ else reresume sume play Video Pause if Play: playing/ resume Video Activate Menu: selected item Not Avail- Stop Stop able Not Available Menu Screens Mode Screen Select Setup Menu Not Available Not Not Available Availabl
KNOWING YOUR VEHICLE SAFETY Remote Control Button Status AM/FM/ MW/LW SAT– Audio Not Available Not Available STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 142 Standard Screens HDD– DISC/ AUX/AUX1/ Hard DVD AUX2 Disc Drive Slow Not Avail- Audio: Not AuMode able Available dio: Not and ConAvailtent Info Menu Screens Mode Screen Select Setup Menu Not Not Available Available able Video Play: Show Mode Info Video: Show Mode Inf
1. Power – Turns the screen and wireless headphone transmitter for the selected Channel on or off. To hear audio while the screen is closed, press the Power button to turn the headphone transmitter on. 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily. 3. Light – Turns the remote control backlighting on or off. The remote backlighting turns off automatically after five seconds. 4.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 11. MUTE – Press to mute the headphone audio output for the selected channel. 12. SLOW – Press to slow playback of a DVD disc. Press play (▸) to resume normal play. 13. STATUS – Press to display the current status. 14. MODE – Press to change the mode of the selected channel. See the Mode Selection section of this manual for details on changing modes. 15.
Locking The Remote Control All remote control functionality can be disabled as a parental control feature. • To disable the Remote Control from making any changes, press the Video Lock button add follow the radio’s instructions (select menu, rear ves, lock). If the vehicle is not equipped with a DVD player, follow the radio’s instructions to turn Video Lock on. The radio and the video screen(s) indicate when Video Lock is active.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 146 NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video system is turned off. Changing the Audio Mode for Headphones 1.
wear over time through normal use, are specifically not covered (replacement foam is available for a nominal charge). UNWIRED TECHNOLOGY IS NOT LIABLE FOR ANY INJURIES OR DAMAGES TO PERSONS OR PROPERTY RESULTING FROM THE USE OF, OR ANY FAILURE OR DEFECT IN, THE PRODUCT, NOR IS UNWIRED LIABLE FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, PUNITIVE OR OTHER DAMAGES OF ANY KIND OR NATURE WHATSOEVER.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY When Channel 1 is in a video mode, the image is displayed on the first rear seat screen as a full screen image. A popup banner at the bottom of the screen is displayed momentarily over the video image showing any change in status of Channel 2. When Channel 2 is in video mode, the image is displayed on the second rear seat screen as a full screen image.
When in shared disc or satellite video mode both the radio and the VES™ have control of the video functions. The VES™ has the ability to control the following video modes: 1. CD: Ability to Fast Forward, Rewind, and Track Up/Down. 2. CD Changer (in radio): Ability to Disk Up/Down and program all listed CD controls (Fast Forward, Rewind, and Track Up/Down). The VES™ can even control radio modes or video modes while the radio is turned off.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES 6. Remote Locked Out — When the icon is displayed, the remote control functions are disabled. 7. Clock — Displays the time. 8. Channel 1 Shared Status — When the icon is displayed, the audio for Channel 1 is also shared with the radio and playing through the cabin speakers.
control’s ENTER button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control’s navigation buttons (▴, ▾, ▸, ◂) to navigate to the desired digit. 2. When the digit is highlighted, press the remote control’s ENTER button to select the digit. Repeat these steps until all digits are entered. 3.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 152 Disc Features control the remote DVD player's (for versions/markets, where provided) settings of DVD being watched in the remote player. Listening To Audio With The Screen Closed To listen to only audio portion of the channel with the screen closed: • Set the audio to the desired source and channel. • Close the video screen.
When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES™ jacks: 1. Video in (yellow) 2. Left audio in (white) 3. Right audio in (red) Using The Auxiliary Audio/Video Input Jacks (AUX) • Lower the screen or press the POWER button on the remote control to turn the screen on.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 154 CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4.
ADDING FUEL FUEL FILLER CAP (GAS CAP) The gas cap is located behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap has been designed for use with this vehicle. (fig. 115) NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door reinforcement. • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 156 NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The MIL in the instrument cluster may turn on if the gas cap is not secured properly. Make sure that the gas cap is tightened each time the vehicle is refueled. • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
SAFETY OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: • Three-point lap and shoulder belts for all seating positions • Advanced Front Air Bags for driver and front passenger • Supplemental Active Head Restraints (AHR) located on top of the front seats (integrated into the head restraint) (for versions/markets, where provided) • Supplemental Side Air Bag Inflatable Curtains (SABIC) that span the front, second, and third row seating for the driver and
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 158 Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
(Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. • Belts should not be worn with straps twisted. • Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may be safely carried out using mild soap and water.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 160 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly.
5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 162 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING All occupants, including the driver, should not operate a vehicle or sit in a vehicle's seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. NOTE: For more information on properly adjusting and positioning the head restraint, refer to “Adjusting Active Head Restraints” in “Knowing Your Vehicle”.
NOTE: • If you have difficulties or problems resetting the Active Head Restraints, see an authorized dealer. KNOWING YOUR VEHICLE • For safety reasons, have the Active Head Restraints checked by a qualified specialist at an authorized dealer. ACTIVE HOOD SYSTEM (for versions/ markets, where provided) The Active Hood system is intended to enhance pedestrian protection by elevating the vehicle’s hood upon an impact with a pedestrian or other object.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 166 Deployment Sensors And Controls The Electronic Pedestrian Protection Module (EPPM) determines if deployment of the actuators in a frontal impact is required. Based on the impact sensors signals, the EPPM determines when to deploy the actuators. The impact sensors are located within the front bumper area.
The front bumper assembly may affect proper operation of the Active Hood system. The front bumper components should be inspected for damage and replaced if necessary in the event of a frontal impact, even if it occurs at a low rate of speed. NOTE: After any Active Hood deployment, the vehicle should be taken to an authorized dealer immediately. To prevent possible damage, do not slam the rear of the hood to reset it. Press the rear of the hood down until it is approximately 5 mm above the fender.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 168 ENHANCED SEAT BELT USE REMINDER SYSTEM (BELTALERT®) BeltAlert® is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert®) to fasten their seatbelts. The feature is active whenever the ignition is on.
CHILD RESTRAINTS Everyone in your vehicle needs to be buckled up all the time, including babies and children. Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 170 Mass Group Group — up to 10 kg Group 0+ — up to 13 kg Group 1 – 9 to 18 kg Group II – 15 to 25 kg Group III — 22 to 36 kg Front Passenger X X X X X Seating Position (or other site) Intermediate Rear Outboard Rear Center Outboard *U N/A **U *U N/A **U *U N/A **U *U N/A **U *U N/A **U Key of letters used in the table above: U = Suitable for “universal” cat
Vehicle ISOFIX Positions Chart Mass Group Carrycot 0 — up to 10 kg 0+ — up to 13 kg I – 9 to 18 kg II – 15 to 25 kg III – 22 to 36 kg Size Class F G E E D C D C B B1 A Fixture Front Passenger Rear Outboard Rear Center ISO/L1 ISO/L2 (1) ISO/R1 (1) ISO/R1 ISO/R2 ISO/R3 (1) ISO/R2 ISO/R3 ISO/F2 ISO/F2X ISO/F3 (1) (1) (1) X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Key of letters used in the table above: (1) = For the CRS which do not carry
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 172 X = ISOFIX position not suitable for ISOFIX child restraint systems in this mass group and / or this size class. * = Seats in front of child restraint seats may need to be adjusted forward to install the child restraint seat. ** = No access to 3rd row seating positions if Carrycot is installed in vehicle.
All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly. If the child cannot sit with knees bent over the vehicle's seat cushion while the child's back is against the seatback, they should use a belt-positioning booster seat. The child and belt-positioning booster seat are held in the vehicle by the lap/shoulder belt.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES 6. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around the child's lap. NOTE: The lap portion of the seat belt should be low on the hips and as snug as possible. 7. Once the seat belt is long enough to fit properly, insert the latch plate into the buckle until you hear a “click.” (fig. 129) 8. To remove the slack from the lap belt, pull upward on the shoulder portion of the seat belt. 9.
WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision.The child could be badly injured or killed. Follow the manufacturer's directions exactly when installing an infant or child restraint. • A rearward-facing child restraint should only be used in a rear seat. A rearward-facing child restraint in the front seat may be struck by a deploying passenger air bag, which may cause severe or fatal injury to the infant.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES All three second-row passenger seating positions have lower anchorages that are capable of accommodating ISOFIX-compatible child seats. You should never install ISOFIX-compatible child seats so that two seats share a common lower anchorage. If installing child seats in adjacent seating positions, or if your child restraints are not ISOFIX-compatible, install the restraints using the vehicle's seat belts. (fig.
In addition, there are tether strap anchorages located behind each rear seatback, near to the floor. (fig. 132) (fig. 131) ISOFIX Anchorages Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 178 NOTE: • Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. • When using the ISOFIX attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
hear a “click.” Next, extract all the seat belt webbing out of the retractor and then allow the belt to retract into the retractor. As the belt retracts, you will hear a ratcheting sound. This indicates the safety belt is now in the Automatic Locking mode. 2. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 180 NOTE: Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. WARNING! • Child Restraint Anchorages are designed to withstand only those loads imposed by correctly-fitted child restraints.
This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. The SABIC air bags are located above the side windows and their covers are also labeled: SRS AIRBAG. • Supplemental Side Air Bag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch This vehicle is equipped with Supplemental SeatMounted Side Air Bags (SAB).
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional.The protective covers for the air bag cushions are designed to open only when the air bags are inflating.
• Air Bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are calibrated to deploy the side air bags during impacts that require air bag occupant protection. (fig.
KNOWING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Air Bags work with the knee bolsters to provide improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection. SAFETY Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: STARTING AND DRIVING Children 12 years old and under should always ride buckled up in a rear seat.
(Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air Bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Side air bags also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 186 The ORC contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. Also, the ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition is first turned on.
Based on several factors, including the severity and type of collision, the side air bag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating SAB exits through the seat seam into the space between the occupant and the door. The SAB fully inflate in about 10 milliseconds.
KNOWING YOUR VEHICLE In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from IGN ON to IGN OFF. SAFETY If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 188 NOTE: Front and/or side air bags will not deploy in all collisions.
Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 190 • The Air Bag Warning Light remains on after the four to eight-second interval. • The Air Bag Warning Light comes on intermittently or remains on while driving. NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled.
SAFETY TIPS TRANSPORTING PASSENGERS NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 192 The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
(Continued) • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats.Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. • Check mounting of mats on a regular basis.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 194 STARTING AND DRIVING ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 500 km. After the initial 100 km, speeds up to 80 or 90 km/h are desirable.
KEYLESS ENTER-N-GO This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. NORMAL STARTING – GASOLINE ENGINE Using The ENGINE START/STOP Button NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. To start the engine, the transmission must be in PARK or NEUTRAL.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 196 • Press the ENGINE START/STOP button a second time to change the ignition switch to the RUN position (EVIC will display “RUN”), • Press the ENGINE START/STOP button a third time to return the ignition switch to the OFF position (EVIC will display “OFF”).
AFTER STARTING The idle speed is controlled automatically and it will decrease as the engine warms up. 4. After the engine starts, allow it to idle for approximately 30 seconds before driving. This allows oil to circulate and lubricate the turbocharger. NORMAL STARTING – DIESEL ENGINE To Turn Off The Engine Using ENGINE START/STOP Button 1. With the vehicle stopped, place the shift lever in NEUTRAL, then press and release the ENGINE START/STOP button. 2.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 198 Turbocharger “Cool Down” NOTE: Letting the engine idle after extended operation allows the turbine housing to cool to normal operating temperature.
PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or first gear. Manual Transmission – For Versions/Markets, Where Provided The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, press the center button, then lower the lever completely. (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 200 will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application. When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
MANUAL TRANSMISSION (for versions/markets, where provided) WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied.The parking brake should always be applied when the driver is not in the vehicle, especially on an incline. Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. (fig. 140) Use each gear in numerical order, do not skip a gear.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 202 DOWNSHIFTING Proper downshifting will improve fuel economy and prolong engine life. If you skip a gear while downshifting or downshift at too high a vehicle speed,you could damage the engine, transmission, or clutch. To maintain a safe speed and prolong brake life, shift down to second or first when descending a steep grade.
WARNING! • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly pressing the brake pedal. • Unintended movement of a vehicle could injure those in or near the vehicle.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS SIX-SPEED AUTOMATIC TRANSMISSION The shift lever position display (located in the instrument panel cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of the PARK position (refer to “Brake/ Transmission Shift Interlock System” in this section).
the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. WARNING! • Never use the PARK position as a substitute for the parking brake.Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 206 • Before moving the shift lever out of PARK, you must turn the ignition switch from the LOCK/OFF position to the ON/ RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.
When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the AutoStick® mode (refer to “AutoStick®” in “Starting And Driving” for further information) to select a lower gear. Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat buildup.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 208 Overdrive Operation The automatic transmission includes an electronically controlled Overdrive (sixth gear).
DRIVING ON SLIPPERY SURFACES ACCELERATION Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have a collision.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 210 DRIVING THROUGH WATER Driving through water more than a few centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. FLOWING/RISING WATER WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off).
WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 8 km/h when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes. • Getting water inside your vehicle’s engine can cause it to lock up and stall out, and leave you stranded.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 212 Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. NOTE: The GCWR rating includes a 68 kg allowance for the presence of a driver. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.
With Attachment Point • For detachable tow bar, pass the cable through the attachment point and clip it back onto itself. (fig. 142) • For fixed ball tow bar, attach the clip directly to the designated point. This alternative must be specifically permitted by the trailer manufacturer since the clip may not be sufficiently strong for use in the way. (fig.
KNOWING YOUR VEHICLE SAFETY Without Attachment Points • For detachable ball tow bar, you must follow the recommended manufacturer or supplier procedure. (fig. 144) • For fixed ball tow bar, loop the cable around the neck of the tow ball. If you fit the cable like this, use a single loop only. (fig. 145) STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (fig. 144) (fig.
TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW Max.Tongue Wt. ◊ (Gross Trailer Wt.) (5 and 7 Passenger Model) (5 and 7 Passenger Model 1,100 kg 55 kg 1,250 kg 62 kg 3.6L/Automatic 3.7 sq m 2.0L Diesel/Manual 3.
KNOWING YOUR VEHICLE TOWING REQUIREMENTS To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: SAFETY • Do not tow a trailer at all during the first 805 km the new vehicle is driven.The engine, axle or other parts could be dam- STARTING AND DRIVING aged. • Then, during the first 805 km that a trailer is towed, do not drive over 80 km/h and do not make starts at full throttle.
(Continued) • Vehicles with trailers should not be parked on a grade.When parking, apply the parking brake on the tow vehicle. Always, block or "chock" the trailer wheels. • GCWR must not be exceeded. • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized. Towing Requirements – Tires − Do not attempt to tow a trailer while using a compact spare tire.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS WARNING! • Do not connect trailer brakes to your vehicle's hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance.
(fig. 147) Pin Number 1 2 3a 4 5 6 7 Function Left Turn Signal Rear Fog Light Ground/Common Return for Contacts (Pins) 1 and 2 and 4 to 8 Right Turn Signal Right Rear Position, Side Marker Lights, and Rear Registration Plate Illumination Device.b Stoplights Left Rear Position, Side Marker Lights, and Rear Registration Plate Illumination Device.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 220 Automatic Transmission (for versions/markets, where provided) The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, select a lower gear (using the AutoStick® shift control).
chart to determine the accurate attaching points. Other equipment, such as trailer sway controls and braking equipment, trailer equalizing (leveling) equipment and low profile mirrors, may also be required or strongly recommended. (fig. 148) Trailer Tow Hitch Attaching Points And Overhang Dimensions A N/A B 366.71 mm C 501.62 mm D 628.69 mm E (maximum overhang) 1051.93 mm F 472.00 mm RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 222 NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground. Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
WARNING LIGHTS AND MESSAGES INSTRUMENT CLUSTER (fig. 149) KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 224 INSTRUMENT CLUSTER DESCRIPTIONS 1. Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
cycles, and the vehicle has been driven several kilometers at speeds greater than 48 km/h, see your authorized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on momentarily each time the ignition switch is turned to ON/RUN. • Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 226 8. Park/Headlight ON Indicator (for versions/markets, where provided) This indicator will illuminate when the park lights or headlights are turned on. (Refer to “Lights” in “Knowing Your Vehicle” for further information). 9.
The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealants or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING If brake failure is indicated, immediate repair is necessary. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle.You could have a collision. Have the vehicle checked immediately. TECHNICAL SPECIFICATIONS Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD).
14. Rear Fog Light Indicator (for versions/ markets, where provided) This indicator will illuminate when the rear fog lights are on. (Refer to “Rear Fog Lights” in “Knowing Your Vehicle” for further information). 15. Vehicle Security Light (for versions/markets, where provided) This light will flash rapidly for approximately 16 seconds when the vehicle security system is arming and then flash slowly when the system is armed.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS IN AN EMERGENCY JUMP-STARTING If your vehicle has a discharged battery, it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.
WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON.You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery. 1.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 232 WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery.
JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. 3. 4. 5. Turn on the Hazard Warning flashers. Set the parking brake. Place the shift lever in PARK. Turn OFF the ignition. 6.
The winch mechanism is designed for use with the jack-handle only. Use of an air wrench or other power tools is not recommended and it can damage the winch. 3. Pull the spare tire out from underneath the vehicle and raise it upright so the tire's tread is on the ground. 4. Tilt the retainer at the end of the winch cable and remove it from the center of the wheel. (fig. 153) SPARE TIRE STOWAGE NOTE: Refer to “Spare Tire Removal” for information on assembling the winch tools. 1.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS JACKING INSTRUCTIONS WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised.
2. Loosen, but do not remove, the wheel nuts on the wheel with the flat tire. Turn the wheel nuts counterclockwise one turn while the wheel is still on the ground. 3. Place the jack underneath the lift area that is closest to the flat tire. Center the jack saddle between the drain flute formations on the sill flange. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange. (fig. 156) (fig. 157) 4.
KNOWING YOUR VEHICLE SAFETY 6. Install the spare tire. Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. (fig. 158) STARTING AND DRIVING NOTE: • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare.
WARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 11. Place the deflated (flat) tire in the cargo area. Do not stow the deflated tire in the spare tire stowage location. Have the deflated (flat) tire repaired or replaced as soon as possible. 12.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 240 3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
TIREFIT KIT (for versions/markets, where provided) Small punctures up to 6 mm in the tire tread can be sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -20°C. This kit will provide a temporary tire seal, allowing you to drive your vehicle up to 160 km with a maximum speed of 88 km/h. TIREFIT Storage The TIREFIT kit is located in the trunk. (fig. 160) TIREFIT Kit Components And Operation (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 242 Selecting Air Mode Turn the Mode Select Knob (5) to this position for air pump operation only. Use the Black Air Pump Hose (7) when selecting this mode. Selecting Sealant Mode Turn the Mode Select Knob (5) to this position to inject the TIREFIT Sealant and to inflate the tire. Use the Sealant Hose (clear hose) (6) when selecting this mode.
WARNING! • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the TIREFIT kit. • Do not use TIREFIT or drive the vehicle under the following circumstances: − If the puncture in the tire tread is approximately 6 mm or larger. − If the tire has any sidewall damage. − If the tire has any damage from driving with extremely low tire pressure. − If the tire has any damage from driving on a flat tire.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in PARK (auto transmission) or in Gear (manual transmission) and turn Off the ignition. 4. Set the parking brake. (B) Setting Up To Use TIREFIT: 1. Turn the Mode Select Knob (5) to the Sealant Mode position. 2.
If the sealant (white fluid) does flow through the Sealant Hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hose (typically takes 30 70 seconds). As the sealant flows through the Sealant Hose (6), the Pressure Gauge (3) can read as high as 5 Bar. The Pressure Gauge (3) will decrease quickly from approximately 5 Bar to the actual tire pressure when the Sealant Bottle (1) is empty. 2.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE WARNING! TIREFIT is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using TIREFIT. Do not exceed 88 km/h until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you. (E) After Driving: Pull over to a safe location.
4. Clean any remaining sealant from the TIREFIT housing. 5. Position the new Sealant Bottle (1) in the housing so that the Sealant Hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the housing. An audible click will be heard indicating the bottle is locked into place. 6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). 7.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 248 BULB REPLACEMENT Where possible, it is advisable to have bulbs changed at a FIAT Dealership. Proper operation and orientation of the external lights are essential for driving safety and complying with the law. LOW BEAM/HIGH BEAM/FRONT TURN SIGNAL AND FRONT POSITION LAMP 1. Open the hood. 4.
2. Remove the electrical connector from the fog lamp housing. (fig. 163) 3. Firmly grasp the bulb by the two side latches and squeeze them together to unlock the bulb from the back of the front fog lamp housing. 4. Pull the bulb straight out from the keyed opening in the housing. 5. Align the index tabs of the replacement front fog lamp bulb with the slots in the collar of the bulb opening on the back of the front fog lamp housing. Do not touch the new bulb with your fingers.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES 4. Firmly grasp the bulb by the two side latches and squeeze them together to unlock the bulb from the back of the lamp housing. 5. Pull the bulb straight out from the keyed opening in the housing 6. Remove the bulb from the connector socket and install the replacement bulb. 7.
4. Rotate the side repeater lamp in place until the left side engages (you will hear a light click). REAR TURN SIGNAL AND BACKUP LAMP The taillamps are a two-piece design. The tail/stop/rear turn signal lamps are located in the rear corner body panels. The tail and backup lamps are located in the liftgate. Changing the Rear Turn Signal Lamp 1. Open the liftgate. 2. Remove the two fasteners from the inboard side of the taillamp housing. (fig. 167) 3.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES 3. Carefully insert a trim stick (plastic flat-blade tool) between the taillamp housing and the liftgate. Use the trim stick and hand pressure together to disengage the taillamp housing from the liftgate. (fig. 169) 4. Rotate the applicable bulb's electrical connector 1∕4 turn counterclockwise and remove it from the housing. 5. Remove the bulb from the connector socket and install the replacement bulb. 6.
FUSES INTERIOR FUSES The interior fuse panel is located on the passenger side under the instrument panel.
KNOWING YOUR VEHICLE Cavity F121 SAFETY STARTING AND DRIVING F122 F123 F124 Cartridge Fuse MiniFuse 15 Amp Blue 25 Amp Natural 25 Amp Natural 10 Amp Red 10 Amp Red 10 Amp Red WARNING LIGHTS AND MESSAGES F126 IN AN EMERGENCY F127 20 Amp Yellow F128 15 Amp Blue F129 15 Amp Blue F130 15 Amp Blue SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 254 F125 Description Wireless Ignition Node Driver Door Module Passenger Door Module Mirrors Cavity F131 F132 F133 Steering Column Control M
UNDERHOOD FUSES (POWER DISTRIBUTION CENTER) The power distribution center is located in the engine compartment. (fig.
KNOWING YOUR VEHICLE Cavity F149 SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY Cartridge Fuse 30 Amp Pink 30 Amp Pink F152 25 Amp Natural F153 20 Amp Yellow F156 10 Amp Red SERVICING AND CARE F157 10 Amp Red TECHNICAL SPECIFICATIONS F158 CONTENTS 256 Description Starter Solenoid 25 Amp Natural F150 F151 MiniFuse 10 Amp Red Powertrain Control Modules Headlamp Washer Motor – For Versions/Markets, Where Provided Diesel Fuel Heater – For Versions/ Markets, Where Pr
Cavity Cartridge Fuse F169 40 Amp Green F170 F172 F173 F174 F175 F176 F177 MiniFuse 15 Amp Blue 20 Amp Yellow 25 Amp Natural 20 Amp Yellow 30 Amp Green 10 Amp Red 20 Amp Yellow F178 25 Amp Natural F179 10 Amp Red Description Emissions – Partial Zero Emissions Vehicle Motor Emissions – Partial Zero Emissions Vehicle Actuators Spare Anti Lock Brake Valves Siren – For Versions/ Markets, Where Provided Spare Powertrain Control Modules All Wheel Drive Module – For Versions/Markets, Where Provided Sun
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 258 FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between 1st gear and REVERSE.
TOW EYE Your vehicle is equipped with a tow eye that can be used to rescue your vehicle, should it become stranded off road. (fig. 171) Tow eyes are for emergency use only, to rescue a vehicle stranded off road.Do not use tow eyes for tow truck hookup or highway towing.You could damage your vehicle. Tow straps are recommended when towing the vehicle; chains may cause vehicle damage. WARNING! Stand clear of vehicles when pulling with tow eyes. Tow straps and chains may break, causing serious injury.
KNOWING YOUR VEHICLE REAR TOW EYE USAGE The rear tow eye receptacle is located behind a door, located on the left rear bumper fascia. SAFETY To install the tow eye, open the door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle. STARTING AND DRIVING WARNING LIGHTS AND MESSAGES Insert the flat end of the jack handle through the eye and tighten, refer to “Jacking and Tire Changing” for further information.
TOWING A DISABLED VEHICLE Towing Condition Wheels OFF The Ground Flat Tow NONE Wheel Lift Or Dolly Tow Flatbed Rear MANUAL TRANSMISSION • Trans in NEUTRAL • Ignition key in ACC Front NO OK ALL BEST METHOD Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 262 MANUAL TRANSMISSION The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed. Your vehicle may also be towed in a forward direction, with all four wheels on the ground, the shift lever in the NEUTRAL position, and the ignition key in the ACC position.
SERVICING AND CARE KNOWING YOUR VEHICLE MAINTENANCE SCHEDULE MAINTENANCE SCHEDULE – GASOLINE ENGINE Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. SAFETY Thousands Of Kilometers 24 48 72 96 120 144 168 192 Months Flush and replace the engine coolant (or at 60 months). 12 24 36 48 60 72 84 96 • Inspect and replace PCV valve if necessary. • Check battery charge status and possibly recharge.
Thousands Of Kilometers 24 48 72 96 120 144 168 192 Months 12 24 36 48 60 72 84 96 Check condition and wear of front disc brake pads. • • • • • • • • Check condition and wear of rear disc brake pads. • • • • • • • • • • • • • • • • KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY Check and, if necessary, top up fluid levels (brakes/hydraulic clutch, windshield washer, battery, engine coolant, etc.).
(*) Change the automatic transmission fluid and filter(s) at 96 000 km or 48 months if using your vehicle for any of the following: city driving, short (less than 7-8 km) and repeated journeys, or frequent trailer or caravan towing.
KNOWING YOUR VEHICLE MAINTENANCE SCHEDULE — DIESEL ENGINE Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
Thousands Of Kilometers 30 60 90 120 150 180 Months 24 48 72 96 120 144 Check battery charge status and possibly recharge. • • • • • • Check engine control system operation (via diagnostic socket). • • • • • • Visually inspect the condition of the auxiliary drive belt. • • • • Replace the timing belt (*). • Replace fuel filter (Or at least change every 24 months). • • • Replace air filter cartridge (Or at least change every 24 months).
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 268 *** The actual interval for replacement of engine oil and cartridge depends by vehicle usage conditions and is shown through a gauge or a message (if available) on the dashboard or at least every 24 months. Failure to perform the required maintenance items may result in damage to the vehicle.
ENGINE COMPARTMENT — 3.6L (fig. 174) KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS (fig.
KNOWING YOUR VEHICLE ENGINE COMPARTMENT — 2.0L DIESEL (fig. 175) SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 270 (fig.
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future. • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 272 ENGINE OIL Checking Oil Level – Gasoline Engine To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off.
Change Engine Oil – Diesel Engine Refer to the “Maintenance Schedule” for the proper maintenance intervals. Engine Oil Viscosity – 3.6L Gasoline Engine SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle.
KNOWING YOUR VEHICLE do not need to be removed to access the compartment. Remote battery terminals are located in the engine compartment for jump-starting. SAFETY To access the battery, turn the steering wheel fully to the right and remove the access panel from the inner fender shield. STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 274 WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you.
WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. • The air conditioning system contains refrigerant under high pressure.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING 3. Pivot the glove box downward. 4. Disengage the two retaining tabs that secure the filter cover to the HVAC housing and remove the cover. (fig. 177) 5. Remove the A/C air filter by pulling it straight out of the housing. 6. Install the A/C air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover.
BODY LUBRICATION Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES Rear Wiper Removal/Installation (for versions/markets, where provided) 1. Lift the pivot cap on the rear wiper arm upward, this will allow the rear wiper blade to be raised off of the liftgate glass. (fig. 178) 4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place.
When refilling the washer fluid reservoir, apply some washer fluid to a cloth or towel and wipe the wiper blades clean. This will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. The fluid reservoir will hold nearly 4 Liters of washer fluid when the “Washer Fluid Low” message appears in the EVIC display.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 280 WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “SafetyTips/Exhaust Gas” in “Safety” for further information.
Car maintenance should be done at a FIAT Dealership. For routine and minor maintenance operations you wish to carry out yourself, we do recommend you have the proper equipment, genuine FIAT spare parts and the necessary fluids;do not however carry out these operations if you have no experience. Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 282 Selection Of Coolant – Diesel Engine Use only the manufacturer's recommended coolant (antifreeze). Refer to “Fluids, Lubricants, and Genuine Parts” in “Technical Specifications” for further information. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant (antifreeze) solution.
Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to ensure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 284 If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle.
Overfilling of fluid is not recommended because it may cause leaking in the system. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer's recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Technical Specifications” for further information. WARNING! • Use only manufacturer's recommended brake fluid.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 286 with an improper fluid level will greatly reduce the life of the transmission and the fluid. Selection Of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only manufacturer’s recommended transmission fluid.
MANUAL TRANSMISSION (for versions/ markets, where provided) Fluid Level Check Visually inspect manual transmission for leakage at each oil change. Add fluid, if necessary, to maintain the proper fluid level. Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 4.7 mm below the bottom of the hole. Lubricant Selection Use only manufacturers recommended transmission fluid.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 288 APPEARANCE CARE AND PROTECTION FROM CORROSION Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.
possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • For grease stains, apply a Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 290 WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable,and if used in closed areas they may cause respiratory harm. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.
TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel and is visible from outside of the vehicle through the windshield. This number also appears stamped on the right front door sill under the sill moulding and printed on the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. (fig. 180) (fig.
TIRES — GENERAL INFORMATION TIRE PRESSURE Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: Safety WARNING! • Improperly inflated tires are dangerous and can cause collisions. • Under-inflation increases tire flexing and can result over-heating and in tire failure. • Over-inflation reduces a tire's ability to cushion shock.
KNOWING YOUR VEHICLE SAFETY Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1.6 km after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
SPARE TIRE MATCHING ORIGINAL EQUIPPED TIRE AND WHEEL (for versions/markets, where provided) Your vehicle may be equivalent with a spare tire and wheel in look and function as the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option refer to an authorized tire dealer for the recommended tire rotation pattern.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 296 WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 80 km/h. Temporary use spares have limited tread life.When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare.
WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle's wheels faster than 48 km/h or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed. TREAD WEAR INDICATORS Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. (fig.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 298 performance when replacement is needed (refer to the paragraph on “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
TIRE CHAINS Use of Security Chain Company (SCC) Super Z6 SZ143 or Iceman Z6 IZ-643 cables or equivalent are recommended on 225/65R17 tires. NOTE: Do not use tire chains on a compact spare tire. To avoid damage to your vehicle or tires, observe the following precautions: • Use chains on 225/65R17 tires only. • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 300 NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period on dry pavement. Observe the tire chain manufacturer's instructions on method of installation, operating speed, and conditions for usage.
that result from using methanol/gasoline or E-85 Ethanol blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. Do not use gasolines containing Methanol or E-85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 302 Indiscriminate use of fuel system cleaning agents should be avoided. Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients. These can harm fuel system gasket and diaphragm materials. WARNING! Carbon monoxide (CO) in exhaust gases is deadly.
FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.6L Engine 2.0L Diesel Engine Cooling System * 3.6L Engine and Single- or Dual-Zone Climate Control System 3.6L Engine and Three-Zone Climate Control System 2.0L Diesel Engine and Single- or Dual-Zone Climate Control System 2.0L Diesel Engine and Three-Zone Climate Control System * Includes heater and coolant recovery bottle filled to MAX level. Metric 77.6 Liters 5.6 Liters 5.2 Liters 12.4 Liters 13.7 Liters 9.1 Liters 9.
KNOWING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS ENGINE Component Engine Coolant* SAFETY Engine Oil – 3.6L Engine** STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 304 Engine Oil – 2.0L Diesel Engine** Spark Plugs – 3.6L Engine Fuel Selection – 3.6L Engine Fuel Selection – 2.0L Diesel Engine Diesel Fuel Additive – 2.0L Diesel Engine Fluids and Lubricants Specs (Genuine Parts) Contact a FIAT Dealership.
CHASSIS Component Automatic Transmission (for versions/ markets, where provided) Manual Transmission (for versions/ markets, where provided) Wheel-Side Constant Velocity Joints Differential-Side Constant Velocity Joints Brake/Clutch Master Cylinder Power Steering Reservoir Windshield/Rear Window Washer Fluid Fluids and Lubricants Specs (Genuine Parts) Totally synthetic lubricant that meets FIAT Classification 9.55550-AV4 (TUTELA TRANSMISSION FORCE4, Contractual Technical Reference N° F108.
ARRANGEMENTS FOR DEALING WITH THE VEHICLE AT THE END OF ITS LIFE FIAT has been committed for many years to safeguarding the environment through the constant improvement of its production processes and manufacturing products that are increasingly “eco-compatible”.
307
308
CONTENTS About Your Brakes . . . . . . . . . . . . . . . . . . . . 112,199 ABS (Anti-Lock Brake System) . . . . . . . . . . 113,114,228 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . . 282 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . . 278 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 301 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . . . 273 Air Conditioner Maintenance . . . . . .
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 310 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 112,284 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . 113,114 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 284,305 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 284 Parking . . . . . . .
Diesel Engine . . . . . . . . . . . . . . . . . . . . . . . . . 280 Disposal of Used Coolant . . . . . . . . . . . . . . . . . 283 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . . . 281 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Points to Remember . . . . . . . . . . . . . . . . . . . . 283 Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . . 283 Radiator Cap . . . . . . . . . . . . . . . . . . . . . . . . . 283 Selection of Coolant (Antifreeze) . . .
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 312 Exhaust Gas Caution . . . . . . . . . . . . . . . . . 106,191 Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . . 196 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 300 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 230 Oil . . . . . . . . . .
Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Octane Rating . . . . . . . . . . . . . . . . . . . . . . 300,304 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 300 Saver Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 304 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . 303 Fuel Optimizer . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Fuel Saver . . . . . . . . .
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 314 Instrument Panel and Controls . . . . . . . . . . . . . . . . . 6 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . . 289 Instrument Panel Lens Cleaning . . . . . . . . . . . . . . . 290 Interior Appearance Care . . . . . . . . . . . . . . . . . . . 289 Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Interior Lights . . .
Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 75 Instrument Cluster . . . . . . . . . . . . . . . . . . . 71,224 Intensity Control . . . . . . . . . . . . . . . . . . . . . . . . 74 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252 Lights On Reminder . . . . . . . . . . . . . . . . . . . . . . 72 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,22 Low Tire . . . . . . . . . . . .
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 316 Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Mode Fuel Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Modifications/Alterations, Vehicle . . . . . . . . . . . . . . . 5 Monitor, Tire Pressure System . . . . . . . . . . . . . . . . 122 Multi-Function Control Lever . . . . . . . . . . . . . . . . .
Rear Drive Assembly . . . . . . . . . . . . . . . . . . . . . . 287 Rear Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Rear Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Rear Park Sense System . . . . . . . . . . . . . . . . . . . . 128 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . 49,54 Rear Window Defroster . . . . . . . . . . . . . . . . . . . . 80 Rear Window Features . . . . . . . . . . . . . . . . . . . . . 79 Rear Wiper/Washer . . . . . . .
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 318 Sentry Key Programming . . . . . . . . . . . . . . . . . . . . 12 Sentry Key Replacement . . . . . . . . . . . . . . . . . . . . 11 Service Engine Soon Light (Malfunction Indicator) . . . 224 Shoulder Belt Upper Anchorage . . . . . . . . . . . . . . 161 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Side Airbag . . . . . . . . . . .
Jacking . . . . . . . . . . . . . . . . . . Life of Tires . . . . . . . . . . . . . . Pressure Monitor System (TPMS) Radial . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . Rotation . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . Spare Tire . . . . . . . . . . . . . . . Spinning . . . . . . . . . . . . . . . . . Trailer Towing . . . . . . . . . . . . . Tread Wear Indicators . . . . . . . To Open Hood . . . . . . . . . . . . . .
KNOWING YOUR VEHICLE SAFETY STARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCY SERVICING AND CARE TECHNICAL SPECIFICATIONS CONTENTS 320 Washer Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Washers, Headlight . . . . . . . . . . . . . . . . . . . . . . . . 78 Washers, Windshield . . . . . . . . . . . . . . . . . . 76,77,278 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 288 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . .
Notes
Notes
Notes
Notes Fiat Group Automobiles S.p.A. - Parts & Services - Technical Services - Service Engineering Largo Senatore G. Agnelli, 3 - 10040 Volvera - Torino (Italia) Print n. 530.02.
WHY CHOOSING GENUINE PARTS We really know your car because we invented, designed and built it: we really know every single detail. At Fiat Service authorised workshops you can find technicians directly trained by us, offering quality and professionalism for all service operations. Fiat workshops are always close to you for the regular servicing operations, season checks and practical recommendations by our experts.
ENGLISH The data contained in this publication is intended merely as a guide. FIAT reserves the right to modify the models and versions described in this booklet at any time for technical and commercial reasons. If you have any further questions please consult your FIAT dealer. Printed in recycled paper without chlorine.