Installation Guide

39-15/16 in.
(42 in. rail height)
33-15/16 in.
(36 in. rail height)
2-3/16 in.
Figure 1
RAIL ON COMPOSITE POST INSTALLATION
Step 1: Install bottom angle / stair rail bracket.
Measure up 2-3/16 in. from the deck surface and mark this location with a
pencil onto the post (Figure 1). Locate the bottom rail bracket against the
post, aligning the BOTTOM of the bracket with the 2-3/16 in. marked line.
Take care to ensure the bracket is centered on the post. Mark the center of
the two mounting holes located inside the bracket against the post.
Pre-drill the marked holes with a 1/8 in. drill bit. Locate the bracket over the
pre-drilled mounting holes, and install two #12 x 2 in. screws through the
bracket and post sleeve and into the wood post. Do not overtighten screws.
Step 2: Install top angle / stair
rail bracket.
Measure up 33-15/16 in., for 36 in. rail height,
or 39-15/16 in., for 42 in. rail height, from the
deck surface and make a horizontal line with a
pencil onto the post (Figure 2). Locate the top rail
bracket against the post, aligning the BOTTOM
of the bracket with the marked line. Take care to
ensure the bracket is centered on the post. Mark
the center of the two mounting holes located
inside the bracket against the post.
Pre-drill the marked holes with a 1/8 in. drill bit.
Locate the bracket over the pre-drilled mounting
holes, and install two #12 x 2 in. screws through
the bracket and into the wood post. Do not
overtighten screws.
TOOLS REQUIRED
• Power drill
• 1/8 in. drill bit for (optional pilot hole pre-drilling)
• 1/4 in. drill bit
• Tape measure
• Plumb bob or level
• Saw for cutting aluminum
• Screwdriver or power drill for T25 Torx screws
• Wrench or ratchet (for post fasteners)
• Safety glasses
• Pencil
• Speed Square
STAIR/ANGLE BRACKET KIT
CONTENTS
• Top Rail Bracket
• Bottom Rail Bracket
• (4) #10 x 3/4 in. Torx Screws
• (4) #12 x 2 in. pan head Torx
Screws (for wood post)
• Instruction Sheet
TIPS The most recent installation instructions can be found on our website. Please visit fiberondecking.com or call customer service at 800-573-8841.
Figure 2
Cover 4 x 4 posts or Fiberon® surface
mount bracket with 5 x 5 Fiberon
composite post sleeve and verify
spacing. Posts should be plumb in
both directions. Place post sleeve base
moulding over post sleeve and slide it
down to the deck surface.
NOTE: Make sure posts are plumb and
level prior to installing the railing.
Step 3: Cut top and bottom rails.
Measure between brackets and add 1-3/8 in. (11/16 in. per side) to this
measurement for inserting the rail ends. Cut top rail to length. Before cutting
the bottom rail to the same length as the top rail, make sure the hole pattern is
centered with the pre-cut baluster hole an equal distance from each end.
 FT. RAIL SECTION
CONTENTS
• 6 . Top Rail
• 6 . Bottom Rail
• Crush Block
• (15) 5/8 in. Balusters
• (18) Spacer Clips
• (12) #10 x 3/4 in. Torx Screws
(bit included)
• Instruction Sheet
 FT. RAIL SECTION
CONTENTS
• 8 . Top Rail
• 8 . Bottom Rail
• (2) Crush Blocks
• (20) 5/8 in. Balusters
• (23) Spacer Clips
• (12) #10 x 3/4 in. Torx Screws
(bit included)
• Instruction Sheet
NOTE: These instructions are applicable to each rail profile and
SKU numbers listed below:
CONTEMPORARY
• 13875
• 13887
• 13877
• 13886
• 13878
TRADITIONAL
• 12296
• 12300
• 12298
• 12302
• 10101
PRIOR TO INSTALLING:
Please consult local zoning laws in regards to load requirements, overall height requirements and bottom space requirements for rails. All supporting structures must
be in accordance with applicable building codes. Neighborhood associations and / or historic districts may regulate size, placement and type of railing. Apply for
permits if required by local authorities and codes. Ensure compliance prior to installation. Local building code requirements will always supersede any and all suggested
procedures and measurements in the following installation. The following installation instructions are intended as a general guideline based on common building
practices used in railing installation.
6 . rail: 68-7/8 in.
8 . rail: 92-7/8 in.
Figure 3
Top View
Same spacing
Page 1 of 2fiberondecking.com
Aluminum Rail Installation with
Composite Post Sleeves
Creation Date: 06/23