Installation Instructions

ManualsBrandsFiberon ManualsDeck PostsAL STR POST 36 BL

ELEMENTS

™

ALUMINUM POST INSTALLATION

TOOLS REQUIRED

• Power drill

• 3/8-in x 6-in drill bit for installing to deck

• 1/4-in x 4-in masonry bit for installing to concrete

• Tape measure

• Plumb bob or level

• Safety glasses

• Wrench or socket (for post fasteners)

• Pencil or marker (for marking hole location)

• Optional PVC adhesive for baseplate cover

KIT CONTENTS

• (1) Post

• (1) Baseplate Cover

• (1) Instruction Sheet

NEED TO PURCHASE (PER POST)

For Wood Installation:

• (4) 5/16-in - 18 x 6-in Bolts Grade 5

• (4) 5/16-in - 18 x 6-in Hex Nuts Grade 5

• (4) 5/16-in - Flat Washers, Small Series N

• (8) 5/16-in - Fender Washers,

Large .06-in Thick, Stainless Steel

TIPS

The most recent installation instructions can be found

our website. Please visit www.ﬁberondecking.com or

call customer service at 800-318-7828.

For Concrete Installation:

• (4) 1/4-in x 3-in Powers Wedge Bolts

• (4) 5/16-in - Flat Washers, Small Series N

POST INSTALLATION TO DECK

Step 1: Position Posts for Deck

Locate posts at equal intervals along the outside of deck (up to 72-in maximum on-

center), placing the edge of the baseplate 2-in from the edge of the deck. If the deck

edge has a overhang, add the overhang distance to the 2-in (Figure 1).

Step 4: Attach Bolts, Washers and Nuts

Place the post into position over the drilled holes and insert a 5/16-in - 18 x 6-in

bolt with small 5/16-in washer into each of the four holes. Attach two large 5/16-in

washers and one 5/16-in - 18 hex nut to each of the four bolts under the deck

(Figure 3).

Step 3: Drill Holes

Ensure sufﬁcient fasteners and wood reinforcement blocking are used for

installation. A minimum of 4-in of blocking depth is required. Using a 3/8-in drill bit,

drill four holes through the deck board and reinforcement blocking board.

PRIOR TO INSTALLING POST:

Please consult local zoning laws in regards to load requirements and bottom space requirements for rails. All supporting structures must be in accordance with applicable building

codes. Neighborhood associations and/or historic districts may regulate size, type, placement and type of railing. Apply for permits if required by local authorities and codes. Ensure

compliance prior to installation. Local building code requirements will always supersede any and all suggested procedures and measurements in the following installation. The

following installation instructions are intended as a general guideline based on common building practices used in railing installation.

FIBERONDECKING.COM PAGE 1 OF 3

Step 2: Mark Holes to be Drilled

Using the post baseplate as a template, mark the deck surface for drill locations for

each of the four corner holes (Figure 2).

2-in

Fastener

Figure 1

Figure 2

Figure 3

AL END POST 36 BL

AL LINE POST 36 BL

AL STR POST 36 BL

(3/8/18)

4-in

3 1/8-in

3/8-in

hole

Baseplate Detail

7/16-in

Summary of content (3 pages)

PAGE 1
AL END POST 36 BL AL LINE POST 36 BL AL STR POST 36 BL (3/8/18) ELEMENTS™ ALUMINUM POST INSTALLATION PRIOR TO INSTALLING POST: Please consult local zoning laws in regards to load requirements and bottom space requirements for rails. All supporting structures must be in accordance with applicable building codes. Neighborhood associations and/or historic districts may regulate size, type, placement and type of railing. Apply for permits if required by local authorities and codes.
PAGE 2
AL END POST 36 BL AL LINE POST 36 BL AL STR POST 36 BL (3/8/18) POST INSTALLATION TO DECK (CONTINUED) POST INSTALLATION TO CONCRETE Step 5: Loosely Tighten the Post Step 1: Position Posts for Concrete To allow rail and/or stair installation, loosely tighten the nuts, leaving the bolt heads approximately 1-in above the baseplate (Figure 4) Locate posts at equal intervals along the outside of concrete (up to 72-in maximum), placing the edge of the baseplate a minimum of 3 5/8-in from the edge of the con
PAGE 3
Step 4: Attach Bolts with Washers Place the post into position over the drilled holes and insert a 1/4-in x 3-in concrete bolt with small 5/16-in washer into each of the four holes (Figure 3). AL END POST 36 BL AL LINE POST 36 BL AL STR POST 36 BL Step 6: Attach Post Baseplate Cover (3/8/18) After the rails and/or stairs have been installed, plumb and tighten the posts. Position both halves of the baseplate cover on either side of the post above the baseplate and below the bottom rail.