TURBINE POWERED HUMIDIFIER Model: TB-1 The TurboMist™ distributes moisture via a rotating foam system powered by air movement in the furnace plenum. The foam pick up water carried in the unit and disperse moisture into the air. DO NOT DESTROY THESE INSTRUCTIONS MUST REMAIN WITH EQUIPMENT PRODUCT QUESTIONS… CALL FIELD FIRST for answers on product maintenance, operation or replacement part questions. Phone: E-mail: (252)522-3031 fieldtec@fieldcontrols.com English .......Page 1 Français .....
Shaded portions indicate dead or turbulent air. CAUTION: Do not use the TurboMist™ in a down-flow furnace. (The type where the heated air output is from the bottom of the furnace.) INSTALLATION Refer to Figure 1 and Figure 2 for suggested humidifier locations. Do not install in a turbulent or dead air space. In installations where more than one humidifier is used do not place them in a position so that one obstructs the air flow of the other. WARNING: Locate the A-COIL before cutting into plenum chamber.
REASSEMBLE HUMIDIFIER: (FIGURES 6 & 7) 1. Place evaporator assembly and pan into humidifier body making sure evaporator shaft fits into drive hub. 2. Attach float and arm assembly by inserting bracket into mounting hole in the body of humidifier. Insert #8-32 hex head screw provided in bagged hardware and tighten into place. 3. Connect water supply from the saddle valve to the TurboMist™ valve.
MAINTENANCE Your Field TurboMist™ Humidifier puts pure water in the air and traps impurities on the evaporator discs and in the water pan. At the end of each heating season the water pan and float should be cleaned and the saddle valve turned off. Do not use sharp objects or harsh abrasives to clean pan and float. REPLACEMENT PARTS The float valve assembly, evaporator assembly and saddle valve assembly can be obtained as replacement parts as necessary. Refer to the diagram below for description.
HUMIDIFICADOR À TURBINE Model: TB-1 Les sections ombragées indiquent de l’air actif ou une absence de circulation. ATTENTION: Ne pas utiliser le TurboMist™ dans une fournaise à circulation descendante. (Lorsque la sortie d’air chaud se fait au bas de l’appareil.) INSTALLATION Se reporter aux Schémas 1 et 2 pour les emplacements suggérés. Ne pas installer à un endroit où l’air est actif et où il n’y a pas de circulation d’air.
REMONTAGE DE L’HUMIDIFICATEUR: (SCHÉMAS 6-7) 1. Placer l’assemblage de l’évaporateur et le bac dans le corps de l’humidificateur en s’assurant que l’arbre de l’évaporateur s’insère bien dans le moyeu d’entraînement. 2. Attacher le flotteur et armer l’assemblée en insérant crochet dans le corps a’humidificateur. Soi insérer la vis de robinet a fourni dans le matériel de bagged et resserre à sa place. 3. Raccorder l’arrivée d’eau de la vanne à étrier à la vanne du TurboMist™ (Schémas 7 & 8).
ENTRETIEN L’humidificateur TurboMist™ Field vaporise de l’eau pure dans l’air et emprisonne les impuretés sur les disques de l’évaporateur et dans le bac à eau. À la fin de chaque saison de chauffage, le bac à eau et le flotteur devraient être nettoyés et la vanne à étrier devrait être fermée. Ne pas utiliser d’objets coupants ou des abrasifs rugueux pour nettoyer le bac et le flotteur.
HUMIDIFICADOR ACCIONADO A TURBINAP Model: TB-1 ADVERTENCIA: No use el TurboMist™ en una calefacción de circulación descendente. (Del tipo en el que la salida del aire calentado es por la parte inferior de la calefacción.) Las areas sombreadas indican aire viciado o turbulento. INSTALACIÓN Para sugerencias sobre la ubicación del humidificador, consulte las Figura 1 y Figura 2. No lo instale en un espacio con aire viciado ni turbulento. ALERTA: Localice el A-COIL antes de cortar en la camara de calefacción.
VUELVA A ARMAR EL HUMIDIFICADOR: (FIGURA 6 & 7) 1. Coloque la unidad del evaporador y el depósito en el cuerpo del humidificador, asegurándose de que el cuerpo del evaporador encaje dentro del cubo de arrastre. 2. Conecte la flota y arme la asamblea metiendo paréntesis en el cuerpo de humedecedor. La adición auto utiliza enrosca proporcionado en empaquetó hardware y aprieta en el lugar. 3. Conecte el suministro de agua de la válvula de silla a la válvula del TurboMist™.
MANTENIMIENTO El Humidificador TurboMist™ Field libera agua pura en el aire y captura las impurezas en los discos del evaporador y en el depósito de agua. Al finalizar cada temporada de uso de la calefacción debe limpiarse el depósito de agua y el flotador, y debe cerrarse la válvula de silla. Para limpiar el depósito y el flotador, no use objetos afilados ni abrasivos fuertes.
Page 11
WARRANTY INFORMATION ONE YEAR LIMITED WARRANTY The products of The Field Controls Co. are warranted to be free from defects in material and workmanship under normal use for one year from date of purchase. In the event of malfunction or failure of this product, the purchaser should properly package the entire unit and ship it PREPAID with return address to the address listed below.