Brochure

ManualsBrandsField Controls ManualsAir CleanerUV-18HP

www.ﬁeldcontrols.com

Please retain these instructions after installation.

This device MUST be installed by a qualiﬁed agency in accordance with the manufacturer's installation instructions. The deﬁnition of

a qualiﬁed agency is: any individual, ﬁrm, corporation or company which either in person or through a representative is engaged

in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the

precautions required, and has complied with all the requirements of the authority having jurisdiction.

This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for

use in the mitigation, treatment, or prevention of any disease or condition.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.

Installation Date:

Installed By: Phone:

UV-AIRE

AIR PURIFYING SYSTEM

Model: UV-12C, 18C, 28C, 28, 12HP, 18HP, 28HP, 12HPC, 18HPC, 28HPC

*Exclusive 5 position lamp mounting feature!

ITEMS INCLUDED IN KIT:

1- UV-Aire power unit

4- Sheet metal mounting screws

1- Angled mounting bracket

1- Flat mounting bracket

1- Duct board mounting bracket

1- Ultra Violet Lamp

1- Instruction Sheet

1- Wing nut

Caution Labels

Gasket

WARNING: DO NOT mount this unit outdoors.

 •Thisproductisdesignedforindoorinstallationonly(i.e.attics,crawlspaces,basements,etc.).

WARNING: UV light will break down plastic materials not rated for UV exposure:

  (Examples:wireinsulation,exduct,drainpansandhumidiers)

 •Theunitmustbemountedatleast30”fromtheabovestatedtypeofmaterials.

 •Ifitisnecessarytomounttheunitindirectlineofsightofthesetypesofmaterials,theymustbe 

shielded with aluminum foil, aluminum foil tape, or sheet metal.

SAFETY CONSIDERATIONS

WARNING: Never expose eyes or skin to UV-C light from any source.

 •LookingdirectlyattheUV-Clightmaycausepermanenteyedamageorblindness.

 •NeveroperatetheUV-AireAirPurifyingSystemoutoftheplenum.

 •Designedforaclosedductsystem.Donotmountnearareturnairopening

 •AllductopeningsindirectlineofsiteoftheUVlightmustbesealedwithducttapeorequivalent

sealing methods.

UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a home’s

heating and air conditioning system. The treatment is a safe, silent, and proven way to make your home a

healthier place to live.

Summary of content (12 pages)

PAGE 1
® UV-AIRE AIR PURIFYING SYSTEM Model: UV-12C, 18C, 28C, 28, 12HP, 18HP, 28HP, 12HPC, 18HPC, 28HPC *Exclusive 5 position lamp mounting feature! ITEMS INCLUDED IN KIT: 1- UV-Aire power unit 4- Sheet metal mounting screws 1- Angled mounting bracket 1- Flat mounting bracket 1- Duct board mounting bracket 1- Ultra Violet Lamp 1- Instruction Sheet 1- Wing nut Caution Labels Gasket UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a home’s heating and air conditioning sy
PAGE 2
INDICATION FOR USE This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for use in the mitigation, treatment, or prevention of any disease or condition. GENERAL INFORMATION There are different size units available, depending on the square footage of your home. See chart below for determining your home’s needs. Model Minimum Volts Amps Duct Width Hz Watts Max Air Temp ºF Lamp Intensity Recommended at 1 meter Max. Sq.
PAGE 3
INSTALLATION 1. Locate a suitable location for the unit downstream from the 'A' coil in the supply plenum or in the return plenum; preferably downstream from the air filter. For optimum cleaning effect on the 'A' coil, mount the unit in the supply plenum as close as possible to the 'A' coil.
PAGE 4
2. Determine the type of duct you have. IF YOU HAVE FLEX DUCT For installations on duct systems with a metallic main duct and flex duct branches, follow the instructions in figure 2A below. Figure 2A IF YOU HAVE METAL DUCT: a. Apply supplied wet and stick mounting template to air duct in either a vertical or horizontal position as shown in Figure 2B. b. Drill 1⁄8” diameter mounting holes at positions indicated on template. c. Cut out the marked openings on the template.
PAGE 5
IF YOU HAVE DUCT BOARD: a. Mount the supplied metal mounting plate onto the duct with duct tape in either a vertical or horizontal position. (See Figures 2B & 3) b. Bend tabs outward as shown in Figure 4. c. Using a knife or blade, cut out a rectangle opening in the duct using the mounting plate as a template. (See Figure 5) d. Remove the cut piece of duct. (See Figure 6) e. Bend both tabs down and through duct at first bend point. (See Figures 7 & 8) f.
PAGE 6
3. Remove base unit and cover from box. 4. Apply supplied Duct Seal Kit according to instructions included in kit. (See Figure 12) 5. Determine whether to use flat or angled bracket. (Refer to Bulb Mounting Bracket Selection) a. Flat Bracket Installation i. Remove the two hex nuts and flat bracket from included bagged hardware. Figure 12 ii. Install the flat bracket and secure to the unit base with the hex nuts provided. (See Figure 13) b.
PAGE 7
9. Swing the swivel bracket over the end of lamp. Hand-tighten the wing nut on the stud. Be careful not to over tighten the wing nut. The porcelain at the lamp base may crack when over tightened. (See Figure 17) 10. Plug ballast plug into end of lamp. (See Figure 18) 11. Snap cover onto the unit base. (See Figure 19) 12. Plug the LED wire from the cover onto the board. (See Figure 20) 13. Close the cover and tighten cover screw. (See Figure 21) 14. Plug the power cord into a standard electrical outlet.
PAGE 8
INCORPORATING A THERMOSTAT (Be sure to follow any applicable state or local codes.) The UV Aire units supplied with a circuit board allow for the automatic operation of the UV lamp when the there is a call for heating or cooling by the thermostat. After the call for heat has been satisfied, the UV Aire unit will operate for 45 minutes then shut off. 1. Turn off power switch on the UV Aire unit and unplug the unit before doing any wiring. 2. Loosen the cover screw and open the unit cover. 3.
PAGE 9
SYSTEM CHECK OUT PROCEDURE 1. Plug the UV Aire back into the power receptacle and leave the power switch in the OFF position. 2. Unplug the Ballast connector from the lamp and switch the power switch to the ON position. The unit will start and operate for approximately 10 seconds. Then the LED will switch to a RED color and the alarm contact will close. 3. Switch the power switch to the OFF position and reconnect the ballast connection to the lamp.
PAGE 10
ANGLED LAMP MOUNTING BRACKET SPECIFICATIONS Use the specifications below to determine allowable clearances for proper mounting of the UV-Aire unit on the duct. LAMP OFFSET DIMENSIONS Unit Min.
PAGE 11
NOTE: UV lamps contain a small amount of mercury, like a typical fluorescent lamp. Check with your local waste management authority for local disposal or recycling requirements. According to the EPA's Universal Waste Rule, these types of lamps may be disposed of into household waste. 5. Insert the lamp through the mounting hole and secure the lamp by rotating the swivel bracket counter-clockwise into position and secure by tightening wing nut. Be careful not to over tighten the wing nut. Figure 22 6.
PAGE 12
LIMITED WARRANTY Field Controls, LLC (“Company”) warrants that its products shall be free from defects in material and workmanship under normal use for the limited period indicated, from the date of manufacture, subject to the provisions 1-8 below. Eighteen (18) months All Field Controls Products (except for those listed below as 5 years or 90 days). Five (5) years Field Controls Direct Vent Systems (FDVS), Field Oil Vent Kits (FOVP), and ComboVents (CV).