Product Overview

ManualsBrandsField Controls ManualsAir CleanerUV-18X

www.ﬁeldcontrols.com

Please retain these instructions after installation.

This device MUST be installed by a qualiﬁed agency in accordance with the manufacturer's installation instructions. The deﬁnition of

a qualiﬁed agency is: any individual, ﬁrm, corporation or company which either in person or through a representative is engaged

in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the

precautions required, and has complied with all the requirements of the authority having jurisdiction.

This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for

use in the mitigation, treatment, or prevention of any disease or condition.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.

Installation Date:

Installed By: Phone:

UV-AIRE

AIR PURIFYING SYSTEM

MODEL: UV-18X

ITEMS INCLUDED IN KIT:

1-UV-Aire

power unit

4-Sheet metal mounting screws

2-Angled mounting brackets

2-Flat mounting brackets

1-Duct board mounting bracket

2-Ultra Violet lamps

1-Instruction Sheet

2-Wing nuts

Caution Labels

Gasket

SAFETY CONSIDERATIONS

WARNING: Never expose eyes or skin to UV-C light from any source.

Looking directly at the UV-C light may cause permanent eye damage or blindness.

•

Never operate the UV-Aire Air Purifying System out of the plenum.•

Designed for a closed duct system. Do not mount near a return air opening•

All duct openings in direct line of site of the UV light must be sealed with duct tape or equivalent •

sealing methods.

WARNING: UV light will break down plastic materials not rated for UV exposure:

(Examples: wire insulation, ﬂex duct, drain pans and humidiﬁers)

The unit must be mounted at least 30” from the above stated type of materials.

•

If it is necessary to mount the unit in direct line of sight of these types of materials, they must be •

shielded with aluminum foil, aluminum foil tape, or sheet metal.

WARNING: DO NOT mount this unit outdoors.

This product is designed for indoor installation only (i.e. attics, crawl spaces, basements, etc.).

•

UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a home’s

heating and air conditioning system. The treatment is a safe, silent, and proven way to make your home a

healthier place to live.

AFTER OPENING THE CARTON, UNPACK AND INSPECT THE UNIT AND LAMP FOR DAMAGE.

DO NOT INSTALL THIS UNIT IF ANY DAMAGE IS NOTICEABLE.

Summary of content (8 pages)

PAGE 1
UV-AIRE® AIR MODEL: PURIFYING SYSTEM UV-18X ITEMS INCLUDED IN KIT: 1-UV-Aire power unit 4-Sheet metal mounting screws 2-Angled mounting brackets 2-Flat mounting brackets 1-Duct board mounting bracket 2-Ultra Violet lamps 1-Instruction Sheet 2-Wing nuts Caution Labels Gasket UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a home’s heating and air conditioning system. The treatment is a safe, silent, and proven way to make your home a healthier place to live.
PAGE 2
INDICATION FOR USE This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for use in the mitigation, treatment, or prevention of any disease or condition. GENERAL INFORMATION There are different size units available, depending on the square footage of your home. See chart below for determining your home’s needs. Model Minimum Duct Width Volts Amps Hz Watts Max Air Temp ºF Lamp Intensity at 1 meter Recommended Max Sq.
PAGE 3
2. Determine the type of duct you have. IF YOU HAVE FLEX DUCT For installations on duct systems with a metallic main duct and flex duct branches, follow the instructions in figure 2A below. "A" (DUCT Ø) "B" (EXT. LENGTH) "C" (MIN DISTANCE) 6" 6" 6" 8" 8" 8" 10" 10" 10" Figure 2A IF YOU HAVE METAL DUCT: a. Apply supplied wet and stick mounting template to air duct in either a vertical or horizontal position. (See Figure 2B) b.
PAGE 4
IF YOU HAVE DUCT BOARD: a. Mount the supplied metal mounting plate onto the duct with duct tape in either vertical or horizontal position. (See Figure 3) b. Bend tabs outward. (See Figure 4) c. Using a knife or blade, cut out a rectangular opening in the duct using the mounting plate as a template. (See Figure 5) d. Remove the cut piece of duct. (See Figure 7) e. Bend both tabs down and through duct at first bend point. (See Figures 8 & 9) f.
PAGE 5
3. Remove base unit and cover from box. 4. Apply supplied “Duct Seal Kit” according to instructions included in kit. (See Figure 12) 5. Determine whether to use flat or angled bracket. (Refer to UV-Aire Configurations in Section III for aid in this decision) a. Flat Bracket Installation i. Remove the two hex nuts and flat bracket from included bagged hardware. ii. Install the flat bracket and secure to the unit base with the hex nuts provided. (See Figure 13) b.
PAGE 6
11. Replace cover on unit. Tighten side screws. (See Figure 19 & 20) 12. Plug the power cord into a standard electrical outlet. NOTE: Seal the joints and seams of the plenum near the mounting location to reduce any direct viewing of light. (See Figure 1) 13. Flip switch on box to the ‘ON’ position. (Light on switch should be on indicating power.) 14. Look through view port in the box cover to be sure lamp is working. You should see a blue glow.
PAGE 7
ANGLED LAMP MOUNTING BRACKET SPECIFICATIONS Use the specifications below to determine allowable clearances for proper mounting of the UV-Aire unit on the duct. Diagram B Diagram A Lamp Center Line For Angled Double Lamp Installation Lamp Offset Dimensions Unit Min. Duct Size (inches) "A" Dimension (inches) UV-18X 14 x 18 Center on Duct Housing Unit A B UV-18X 13- ⁄2" 10-5⁄16" 1 MAINTENANCE 1. Inspect and clean lamp at least every 6 months. 2.
PAGE 8
REPLACEMENT PARTS LIST MODEL LAMP (Field Controls Part Number) BALLAST (Field Controls Part Number) UV-18X 46365402 46365503 For replacement parts, contact your local heating service company. Any questions, please contact Field Controls at: • Phone: 252-522-3031 • Fax: 252-522-0214 • Email: sales@fieldcontrols.