User Guide

ManualsBrandsFieldpiece ManualsChargingWireless Vacuum Gauge

Settings Menu

The settings menu can be entered when

in standard operating mode. Selecting a new

setting automatically exits the menu. This saves

time getting in and out of the menu quickly

for your most commonly changed setting (e.g.

wireless).

1. Hold ENTER to enter* the settings menu.

The menu starts where you last exited.

2. Press NEXT to view next setting.

The menu loops so keep going if you skipped

the setting you want to change.

3. Press ENTER to select the setting.

4. Press NEXT to increase the setting value.

The setting values loop so keep going if you

skipped the value you want to save.

5. Press ENTER to save* the new value and exit.

* Hold ENTER to exit the menu without saving.

List of Settings

Start : Enable Wireless (if o)

Stop : Disable Wireless (if on)

Auto O : Set Auto O Timer

Units : Set Unit of Measure

Alarm Lo : Set Low Alarm Level

Alarm Hi : Set High Alarm Level

Mute : Enable Speaker (if o)

Unmute : Disable Speaker (if on)

BkLtTime : Set Backlight Timer

Firmware : View and Update Firmware

Restore : Restore Default Settings

Wireless

Start or stop sending wireless measurements.

Live measurements can be sent to SMAN

manifold (overrides its internal vacuum gauge),

and to the Job Link mobile app for added

capabilities such as live trending. Wireless is

disabled by default to maximize battery life.

Auto Power Oﬀ Timer (APO)

Set the timer for the gauge automatically

powering o. The timer is reset when a button

is pressed. The timer is disabled in alarm mode.

(15min, 30min, 45min, 60min, Disabled)

Units

Set the unit of vacuum measurement. Alarm

levels are automatically converted to match the

unit setting.

(Microns, Pascals, mBar, mTorr, Torr, mmHg)

Low Alarm Level ( )

Set the vacuum level required to trigger the

low alarm. Hold NEXT for quicker scrolling.

(50 - 500 - High Alarm)

High Alarm Level ( )

Set the vacuum level required to trigger the

high alarm. Hold NEXT for quicker scrolling.

(Low Alarm - 1000 - 9000)

Mute ( )

Mute or unmute the speaker. Button presses

and alarms remain silent if the speaker is muted.

The icon appears if the speaker is muted.

Backlight Timer

Set the timer for the backlight automatically

turning o. The timer is reset when a button is

pressed.

(10s, 20s, 1min, 2min, 5min, 10min, 15min, 30min)

Firmware

Check the firmware version (X.XXX.X) by

reading the first 4 digits. If a new version is

available from the Job Link mobile app, initiate

the update from your mobile device.

Restore

To restore all settings to their factory defaults,

press NEXT until "YES" is displayed and press

ENTER to conrm. To exit without restoring,

select "no" or hold ENTER.

Evacuation Tips

MAXIMIZE FLOW

• Remove Schrader valve cores with a removal

tool.

• Remove valve depressors from hoses.

• Use shortest vacuum rated hoses with largest

diameter available.

• Do not evacuate through hoses with low loss

ttings.

TRUST YOUR TEST

• Inspect the rubber seals at both ends of your

hoses for damage. Replace as needed.

• Change pump oil before and during the job.

Change pump oil on-the-y without losing

vacuum with Fieldpiece vacuum pumps.

• When the vacuum pump is isolated from the

system, a slow rise that stabilizes may signify

moisture is still present in the system. A con-

tinuous rise to atmosphere indicates a leak.

Check hoses, tools, or the system itself.

• Measurements are less representative of the

entire system when the vacuum pump is on

because pumping creates a pressure gradi-

ent. Isolate the pump and allow the system to

stabilize before assuming the measurement

represents the entire system.

Certiﬁcations

and Module IDs

FCC Statement

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment o and on, the user is encouraged to try to correct the

interference by one of the following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit dierent from that

to which the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or

modications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

(Example - use only shielded interface cables when connecting to

computer or peripheral devices).

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This device complies with Industry Canada licence-exempt RSS-247

standard. Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation

of the device.

IC Radiation Exposure Statement: This equipment complies

with IC RSS-102 radiation exposure limit set forth for an uncontrolled

environment. This equipment should be installed and operated with

minimum distance 0.5 cm between the radiator and your body.

Fieldpiece Instruments 1636 West Collins Avenue, Orange, CA 92867

IFETEL Statement

La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia

perjudicial y (2) este equipo o dispositivo debe aceptar cualquier

interferencia, incluyendo la que pueda causar su operación no deseada.

The operation of this equipment is subject to the following two

conditions: (1) this device or device may not cause harmful interference,

and (2) this device or device must accept any interference, including

interference that may cause undesired operation.

ANATEL Statement

Este equipamento não tem direito à proteção contra interferência

prejudicial e não pode causar interferência em sistemas devidamente

autorizados.

This equipment is not subject to the protection from harmful

interference and may not cause interference with duly authorized

systems.

Limited Warranty

This product is warranted against defects in material and

workmanship for one year from date of purchase from an authorized

Fieldpiece dealer. Fieldpiece will replace or repair the defective unit,

at its option, subject to verication of the defect.

This warranty does not apply to defects resulting from abuse,

neglect, accident, unauthorized repair, alteration, or unreasonable

use of the instrument.

Any implied warranties arising from the sale of a Fieldpiece product,

including but not limited to implied warranties of merchantability and

tness for a particular purpose, are limited to the above. Fieldpiece

shall not be liable for loss of use of the instrument or other incidental

or consequential damages, expenses, or economic loss, or for any claim

of such damage, expenses, or economic loss.

State laws vary. The above limitations or exclusions may not apply

to you.

Obtaining Service

For international customers, warranty for products purchased

outside of the U.S. should be handled through local distributors. Visit

our website to nd your local distributor.

EN 300 328

2ALHR003

00263-18-10972

IC: Industry Canada

22518-BT003

IFETEL: Federal Telecom Institute

RCPFI2A18-0235

Regulatory Compliance Mark

Waste Electrical and

Electronic Equipment

Restriction of Hazardous

Substances Compliant