User Guide

ManualsBrandsFieldServer ManualsOtherFS-8700-60

A Sierra Monitor Company

APPLICABILITY & EFFECTIVITY

Effective for all systems manufactured after May 1, 2001

Driver Manual

(Supplement to the FieldServer Instruction Manual)

FS-8700-60 Gardner Denver Auto Sentry

ES/RS2000

Summary of content (13 pages)

PAGE 1
A Sierra Monitor Company Driver Manual (Supplement to the FieldServer Instruction Manual) FS-8700-60 Gardner Denver Auto Sentry ES/RS2000 APPLICABILITY & EFFECTIVITY Effective for all systems manufactured after May 1, 2001
PAGE 2
FS-8700-60 Gardner Denver Manual Table of Contents TABLE OF CONTENTS 1. Gardner Denver Auto Sentry ES/RS2000 Description....................................... 1 2. Driver Scope of Supply........................................................................................ 2 1.01 Supplied by FieldServer Technologies for this driver ....................................... 2 1.02 Provided by the Supplier of 3rd Party Equipment.............................................. 2 2.1.1.
PAGE 3
FS-8700-60 Gardner Denver Manual 1. Page 1 of 11 Gardner Denver Auto Sentry ES/RS2000 Description The Gardner Denver Auto Sentry ES/RS2000 driver allows the FieldServer to transfer data from devices over either RS-232 or RS-485 using Gardner Denver Auto Sentry ES/RS2000 protocol. The driver can be configured to communicate with ES Controllers with software versions V2.0X, V2.1X and RS2000 Controllers with software versions V4.
PAGE 4
FS-8700-60 Gardner Denver Manual 2. Page 2 of 11 Driver Scope of Supply 1.01 Supplied by FieldServer Technologies for this driver FieldServer Technologies PART # FS-8915-10 FS-8917-03 FS-8700-60 Description UTP cable (7 foot) for RS-232 use RJ45 to DB9M connector adapter Driver Manual Provided by the Supplier of 3rd Party Equipment 1.02 2.1.1. Required 3rd Party Hardware Part # Description 2.1.2. ES/RS2000 controller Required 3rd Party Software None. 2.1.3.
PAGE 5
FS-8700-60 Gardner Denver Manual 3. Page 3 of 11 Hardware Connections The FieldServer is connected to the ES/RS2000 Controller as shown in the connection drawing below: Configure the ES/RS2000 Controller according to manufacturer’s instructions. 1.03 Hardware Connection Tips / Hints If inter-controller communications are set up for the controller, connect to the RS-232 port only. If inter-controller communications are not used, connect to either the RS232 or RS-485 port of the Controller.
PAGE 6
FS-8700-60 Gardner Denver Manual 4. Page 4 of 11 Configuring the FieldServer as a Gardner Denver Auto Sentry ES/RS2000 Client For a detailed discussion on FieldServer configuration, please refer to the FieldServer Configuration Manual. The information that follows describes how to expand upon the factory defaults provided in the configuration files included with the FieldServer (See “.csv” sample files provided with the FieldServer).
PAGE 7
FS-8700-60 Gardner Denver Manual 1.
PAGE 8
FS-8700-60 Gardner Denver Manual 1.06 Page 6 of 11 Client Side Node Descriptors Section Title Nodes Column Title Node_Name Node_ID Protocol Connection Node_Type* Function Legal Values Up to 32 alphanumeric characters Provide name for node Unit number connected to an ES/RS2000 controller Specify protocol used Specify which port the device is connected to the FieldServer Sets the protocol to be used for different Controller software versions 1-8 Gardner_Denver P1-P8, R1-R21 ES V2.0X ES V2.
PAGE 9
FS-8700-60 Gardner Denver Manual 4.1.2. Page 7 of 11 Driver Related Map Descriptor Parameters Column Title Function Legal Values Node_Name Name of Node to fetch data from Gar_cmd Data poll commands Gar_data Data fields in a data poll command response message. Can be used to poll for all or specific data or just isolate specific items in a “All” poll.
PAGE 10
FS-8700-60 Gardner Denver Manual 4.1.4. Page 8 of 11 Map Descriptor Example 1 – Polling all available Controller Data Map_Descriptor_Name, GD_MBA1, GD_MBA2, GD_MBA3, Data_Array_Name, DA_Service_Data, DA_Oper_Mode, DA_Oper_Data, Data_Array_Offset, 0, 0, 0, Note the active Read Block Continuous map descriptor function responsible for polling the Controller. Function, RDBC, RDBC, RDBC, Node_Name, Node_1, Node_1, Node_1, The Gar_cmd field indicates the poll is for Operating Data.
PAGE 11
FS-8700-60 Gardner Denver Manual Page 9 of 11 Motor current4 4 4.1.5. Map_Descriptor_Name, GD_MBA1, GD_MBA2, GD_MBA3, amps Map Descriptor Example 2 - Polling only specific data items Data_Array_Name, DA_Hourmeter, DA_Oper_Mode, DA_Motor_Amps, Data_Array_Offset, 0, 0, 0, Note the active Read Block Continuous map descriptor function responsible for polling the Controller. 4.1.6.
PAGE 12
FS-8700-60 Gardner Denver Manual Page 10 of 11 Appendix 1. Advanced Topics Appendix 1.1. Can I use only Passive Client mapdescs ? No. A passive client map descriptor must be used after an active RDBC map descriptor. The driver uses the active map descriptors to poll the Controller and then searches for Passive Client map descriptors with matching Node_Name and Gar_Cmd fields. It then stores the data items as specified by the Gar_data field from the data collected by the preceding active map descriptor.
PAGE 13
FS-8700-60 Gardner Denver Manual Page 11 of 11 Appendix 2. Revision History DR DR Driver Ver. 1.00a 1.02b 1.03a Doc. Rev. 1 2 3 Meg Meg 1.03a 4 Meg Meg 1.03a 5 1.03a 6 Date Resp Format 9/2/02 4/12/04 7/12/04 JDM DR DR 7/16/04 8/24/04 12/29/04 JD Comment Applying new template. Updated Updated connection diagram Redrew connection diagram. Reformatted document. Replaced connection diagram with original created by Deon.