40 Channel Auto Searching Wireless FPV monitor WITH dUAL rECEIVER LCD MONITOR (BUILT-IN dvr) User Manual
To insure best use of the unit, please read the user’s manual carefully. CAUTION 1. Do not use any damaged or leaking battery and please replace the battery immediately if its working life becomes short significantly. 2. Do not expose this product to direct sunlight, heat or humid conditions. 3. Keep away from strong light while using this product so as to obtain the clearest. Please use sun shade for the outdoor use. 4. Please avoid heavy impact or dropping on the ground. 5.
CONTENTS 1. Product description -------------------------------------- 5 2. DVR (Video) Operation instruction---------------- 9 3. Wireless transmission receive operation------19 4. Operation instructions -------------------------------- 22 5. Sun shade installation --------------------------------- 28 6. Power Supply ----------------------------------------------- 28 7. Parameters -------------------------------------------------- 30 8.
1. Product description 1.1 Front view: 1. Video Indicator 2. Power Indicator ★ 3～8. 3. SC.SHOT : Real-time images snapping 4. REC/OK : Recording start, stop/ function confirm 5. MODE : Mode key to enter/ exit the playback mode 6. MENU : Menu key to enter/ exit the DVR (Video) menu mode 7. : UP button, up one option 8. : Down button, down one option ★ 9～12.
9. /CH/ : Multi button for UP /Channel Selection /Search / Volume up. Press this button for channel selection, long pressing for channel auto searching. In OSD for “UP” button, Volume up 10. /BAND: Multi button for DOWN /Channel Selection /Volume down. Press this button for channel selection 3 from “A、B、E、F、R”. In OSD for “DOWN” button, Volume down 11. : Menu key, press this button to pop up the menu, and the current menu and sub-menu item to confirm the adjustment. 12. 13. 14.
1.2 Rear View: 1. VIDEO OUT: Composite video signal output 2. HDMI IN: HD HDMI signal input 3. VIDEO IN: Composite video signal input 4. USB data upgrade port 5. AUDIO IN: Audio signal input 6. Power switch “ ” Indicates that the power is turned on, “○” means power is turned off. 7 7. Power input jack 8. Battery Pack 9. Speaker 10.
11、 11 is“+”，12 is“-”,Copper Screw size:M3×9.5mm A: Battery plate locking screw hole, 4 holes, Copper Screw size: M3×5.0mm B: 75×75mm VESA, Screw size: M4×5.0mm 1.
2. DVR (Video) Operation instruction: Check the SD card has been placed into the slot (HDMI input, there is no video recording function). After the device is turned on, press “ ” to select “DVR” channel, press “REC/OK”, then the monitor will be in “RF” channel mode, if you would like to change to “VIDEO”, press “ ”again to change to VIDEO. 2.1 DVR (Video) button instruction： 6 5 4 3 2 1 1. SC.SHOT : Real-time images snapping 2. REC/OK : Recording start, stop/function confirm 9 3.
2.2 Recording start Input signal selection is " DVR " (video signal) channel, the monitor screen will display is “RF” channel on the screen, press the " REC / OK " button and a symbol will appear as a red flashing , meaning that recording begins , the DVR defaults to the RF channel, if you would like to Record “VIDEO” channel, press the to switch (HDMI input cannot record). You want to stop the video, press " REC / OK " button. 2.
2.5 DVR Menu Operation Video setting: Press "MENU" button to enter the video settings menu Resolution D1(720×576), VGA(640×480), QVGA(640×480) The higher the resolution, the sharper the image and has a larger file size.
Loop recording If the SD card is full, it will overwrite the oldest files. Motion Detection When switched on and moving objects are detected, it will automatically record.
Date Stamp Date and time can be superimposed onto the video Record Audio You can choose to record Audio directly to a file or not record. Quality The higher the image quality, the file size will be bigger.
Motion Detection Sensitivity Power on auto recording 2.6 Advanced Settings Continuously twice press the "MENU" button to enter the MENU advanced Settings option.
Format First use, in order to optimize the file system. After entering format mode, press "REC/OK" button to confirm, the menu prompts.
Default Setting Restore to the factory default Settings 2.7 Playback menu Settings Press the "MODE" button, in the top left of the screen will display , press the DVR menu key "MENU".
At this point if you press the "REC / OK" button to enter the playback menu. Delete, delete the unwanted content.
Delete All Protection, to save the contents and utilise lock protection.
3. Wireless transmission receiveR operation 3.1 Channel selection This unit can auto search 40 receiver channels.
(Frequency ranges of each region are different.) 3.2 Auto Search: Turn on the monitor, press “ Long pressing “ ” and select “RF” signal input. ” ,“Auto Searching” will be displayed on the top left corner of the screen, when screen on the upper left corner shows the“BAND:X CH:X”, and when the image is displayed it means it has finished searching.
3.3 Manual Searching and setting: Turn on the monitor, press “ ” and select “RF” signal input. “BAND: X CH: X” will display on the top left corner of the screen, press “ ” to switch channel A/B/E/F/R. Press “ select 1~8 channels.
4. Operation instructions 4.1 Button instructions 4 1. 3 2 1 5 Multi button for UP /Channel Selection /Search / : Volume up: Press this button for channel selection, long press for channel auto search. 2. : Multi button for DOWN/Channel selection/Volume down: Press this button for channel selection from “A、B、E、F”. 3.
Operation Press button 4 ( )to select HDMI, video, RF, DVR input signals Select HDMI, HD multimedia digital signal from the HDMI input port; Select video, video signal from the video input port; Select RF, 5.8 G RF Select DVR to enter into DVR video channel, displayed on the screen at this time is images from the DVR video output. Access DVR channel for corresponding functions. When the DVR video recording, video indicator will light in 5 (blue) flashes.
Color ss. ※ Brightness: To adjust the image's brightness ※ Contrast: To adjust the brightest and darkest ratio of the image. ※Hue: On NTSC Video mode, the image color tint difference is adjustable by tint.
OSD ※ Language: Languages for OSD as below: English、简体 中文、Français、Italiano、Deutsch Espanol 、日本語、 한국의、 Pycc、Portugues ※ H Position: To adjust the OSD position in horizontal. ※ V Position: To adjust the OSD position in vertical. ※ OSD Timeout: To adjust the clock. ※ Transparent: 25 To adjust the level of transparency.
Function ※ Reset: Back to original setting. ※ System: To adjust color video format ※ Display Ratio: To change the display ratio 16:9/4:3.
※ Camera: Using a Canon 5 d II or similar camera, the monitor video has real-time images. NO black screen, NO delay, perfect HD without distortion. Sound ※ Volume: To adjust the volume. ※ Focus: As an auxiliary functions (in HDMI mode ) when used as the camera viewfinder. ※ Ver.1.
5. Sun shade installation 6. Power Supply There are three versions for power supply: 6.1 Supply by power adapter When the monitor is connected to the electricity by DC power adapter, the red light is illuminated, this means charging, after the battery is fully charged, the charging indicators will turned off. When the power switch is on “ ”, the monitor is in operation mode, green light is illuminated.
6.3 Li-ion Battery ● The working temperature of the Li-ion battery is -20~60℃, please don’t use the battery when the temperature is too low or too high. The power of battery will be reduced if it is working in an low temperature environment. Please don’t use the battery in an high temperature environment, may cause battery swell then catch fire. Please check the temperature of battery regularly when working in an high temperature environment.
7. Parameters Panel Size TFT LCD 7.0inch Panel Type TFT LCD Resolution 800*480 pixels Backlight LED Dot Pitch 0.0642(W) x 0.1790(H) mm Display Ratio 16:9 Brightness 1000cd/㎡ Contrast 500:1 Response Time 15ms Viewing Angle 70°/70°(L/R) 50°/70°(U/D) Input Signal Video/Audio/RF/HDMI Output Signal Video Video Color System PAL-4.43 / NTSC-3.58 HDMI support format Headphone Output 480i /480p /576i /576p 720p /1080i /1080p (50/60Hz) stereo 3.
RF Wireless Receiving typical value -90dBm Sensitivity Frequency stability ±100 ppm Unit Size (mm) 188.4L×134H×33.7D (mm) Unit Weight 540g（Including the battery but without antenna and battery plate） 1/4-20 Installation Method thread mounting holes in the monitor, easy to install on the tripod 75X75cm VESA Built-in battery Li-ion 7.4V/2200 mA/h Working Temperature -20～50℃ Storage Temperature -30～65℃ 8. Trouble shooting 8.
② Check signal cable is connected, and make sure you use a standard adapter to connect the monitor. If power is supplied by a battery, please check the battery whether it is fully charged. 8.3 Images are not synchronized, DVR can't enter the menu ① The DVR playback system and monitor system are different, change the format in the "System" option. (NTSC/PAL) ② The RF signal is too weak. 8.
