User guide

Owner's Operation & Safety
Manual
BD1210C (shown)
SAFETY INSTRUCTIONS
Electrical wiring should be done by a
licensed electrician in compliance with
local, state and national electrical code,
ANSI/NFPA 70, 30, 30A as appropriate.
Rigid conduit should be used and a
proper ground must be provided to avoid
the possibility of electrical shock. Failure
to comply with this warning could result
in serious injury and/or loss of property.
Use only static wire, conductive hose
when pumping flammable fluids.
WARNING
This product should not be used for fluid transfer into aircraft. This
product is not suited for use with fluids for human consumption or
fluids containing water.
To ensure safe and efficient operation, it is essential to read and follow
each of these warnings and precautions.
1. Do NOT smoke near pump or use pump near an open flame.
Fire could result.
2. Disconnect power to pump before servicing pump.
3. Take motors needing service to an authorized repair shop to
maintain “explosion-proof” and “rain-proof” integrity.
4. A biodiesel compatible filter should be used on pump outlet to
ensure that no foreign material is transferred to fuel tank.
5. The pump motor is equipped with thermal overload protection.
If overheated, it will shut itself off without any damage to the
windings. Move ON / OFF lever to the ‘OFF’ position to reset
pump.
6. Tank or barrel should be anchored to prevent tipping in both
the full and empty conditions.
7. To minimize static electricity build-up, keep nozzle in contact
with container being filled while filling container.
1
The Fill-Rite Series BD1200C/BD4200D products are positive
displacement, rotary vane pumps. Their rugged motors are explosion-
proof and rain-proof to ensure a long life of dependability.
GENERAL DESCRIPTION
MECHANICAL INSTALLATION INSTRUCTIONS
Do NOT install additional foot valves or check valves unless
they have a pressure relief valve.
DANGER
ELECTRICAL INSTALLATION INSTRUCTIONS
SERIES BD1200C / BD4200D
DC FUEL TRANSFER PUMPS FOR
BIODIESEL B21-B100
(Biodiesel must conform to ASTM D6751 Standard)
CAUTION
Not for use with Gasoline, Diesel Fuel or Biodiesel less than B21.
Use the Fill-Rite® Series FR1200 and FR4200 pumps to dispense
gasoline & diesel fuel.
Follow steps 1 through 7 above.
A. Electically ground the pump to the vehicle (fuel tank pump is
mounted on must also be grounded). To electrically ground
pump, remove green grounding screw located next to junction
box cover. Insert this screw through eyelet of furnished green
grounding wire assembly and refasten it securely to the pump.
The other end of the wire is to be stripped of insulation and the
bare wire securely bonded to the vehicle frame.
CAUTION: Do not connect the positive or negative power to
the green screw or wire as this could cause a fire.
B. Pass the electrical wires to the source of the vehical power
system, supporting the wires as necessary and protecting them
from sharp edges, heat and anything that could damage the wires
and insulation.
C. Attach one end of a 30 amp, slow-blow fuse holder to the red
pump wire. Make a solid electrical connnection with the other end
1. Use Teflon® Tape on all pipe threads
2. Tightly screw suction pipe (21) into inlet flange (1) of pumping unit.
3. Extend suction pipe into tank or barrel to within 3" of tank bottom.
Do not rest suction pipe on bottom of tank.
4. Screw inlet flange of pump into tank or barrel opening. Inlet flange
must be completely and securely threaded into an undamaged tank
or barrel bung.
1. Install pump as described in Mechanical Installation Instructions.
Read and understand all of the electrical wiring
instructions before proceeding.
2. Remove pump’s electrical junction box cover and straighten the 2
wires to make the stripped wire ends accessible outside of the
junction box.
3. Screw furnished cable connector into ½ inch NPT conduit opening
in pump junction box.
4. Strip 6 inches of the outer covering from one end of the furnished
electrical cable being careful not to damage the black and red wire
insulation.
5. Loosen cable connector nut and pass the stripped end of the
furnished cable through the cable connector until 2 inches of the
unstripped cable is within the cable connector. Tighten the cable
connector nut.
6. Strip ½ inch of the installation from the ends of the red and black
cable wires. Using the furnished wire nuts, connect these wires
to the pump wires matching the colors. Be sure no bare wire is
exposed.
7. Fold wires into junction box and replace cover making sure the
gasket is in place. Make sure all screws are seated so there is
no space between the cover and the junction box.
For Vehicle Installation