Installation Guide

ManualsBrandsFIMCO ManualsGarden CenterHigh-Flo 1.2 Gal. Sprayer Pump

Page 1

OWNER’S MANUAL

www.fimcoindustries.com

1000 FIMCO Lane, P.O. Box 1700, North Sioux City, SD 57049

Toll Free Phone: 800-831-0027 : Toll Free Fax: 800-494-0440

[5194678 (09/18)]

Installaon and Service Informaon

Fimco High-Flo High Performance pumps are designed to pump water and aqueous solutions of common pesticides. They are not

designed to pump petroleum products or other flammable materials. They are not designed to pump bleach solutions. Use of this

pump for petroleum products or bleach solutions will void the warranty. When pumping liquids other than water, the pump

should be flushed out with a cleaning solution, such as Fimco Tank Neutralizer & Cleaner, or clean water mixed with a good grade

dish soap after each use to prolong pump life.

This High-Flo High Performance pump is equipped with a demand switch that reacts to outlet pressure and shuts the pump motor off

at a factory set pressure limit of 60 PSI. When the pressure drops below this preset limit the switch allows the pump motor to start

again.

High-Flo High Performance pumps are self-priming. Vertical prime will depend on the viscosity of the liquid and suction line size. Mini-

mum recommended suction line size is 3/8 inch. All hose connections need to be tight or air leakage will break the prime and disrupt

water flow. The installation of a 50 mesh strainer is recommended to prevent debris or other foreign material from entering the pump

and causing pump failure. The pump should be mounted in a dry and adequately ventilated area. The pump can be mounted horizon-

tally or vertically. If mounted vertically, the pump head should be down and the motor should be up. Your pump has two male 3/8”

hose barb fittings molded into the pump head. Use flexible hose or tubing to connect to the inlet and outlet ports on the pump. This

minimizes stress on the pump head. Never use rigid pipe connections. Do not compress the feet. Overtightening will reduce the

ability to isolate vibration & noise.

Your pump is rated at 1.2 GPM @ open flow. If the discharge plumbing is very restrictive or nozzle tips are undersized, the back pres-

sure will cause the pump to cycle rapidly. This rapid cycling will increase the operating temperature of the motor and the amperage

draw on the power supply. Extended use with this cycling will cause premature failure of the pump.

Your pump is designed to run off of the battery of your ATV, lawn tractor, or other vehicle with a 12V system. If using a stand alone

battery, use a deep cycle RV or marine battery.

The pump should be winterized before storage, by pumping a solution of RV antifreeze through it, and the entire plumbing system.

12 Volt, 1.2 GPM, 60 PSI

Diaphragm Pump

Model: HFP-12060-111

(5281370/5151086)

Retain a copy of receipt for your pump.

As it will be required to validate any warranty service.

High-Flo High Performance Pumps are warranted

against manufacturer or workmanship defects for

Two (2) years from date of purchase for home owner

usage and 90 days for commercial usage.

See Page 4 for Warranty Information

Summary of content (4 pages)

PAGE 1
OWNER’S MANUAL 12 Volt, 1.2 GPM, 60 PSI Diaphragm Pump Model: HFP-12060-111 (5281370/5151086) Installation and Service Information Fimco High-Flo High Performance pumps are designed to pump water and aqueous solutions of common pesticides. They are not designed to pump petroleum products or other flammable materials. They are not designed to pump bleach solutions. Use of this pump for petroleum products or bleach solutions will void the warranty.
PAGE 2
Pump Model: 5281370 Available Replacement Parts Replacement Pump: 5151086 DO  Clean and rinse your pump after each use with Fimco Tank Neutralizer  Winterize your pump or sprayer by rinsing, draining and running RV Antifreeze through it before storing for the winter.  Use clean water for your spray mixture  Store inside a building when not in use. DON’T  Use to pump bleach.
PAGE 3
Checking the Pressure Switch: If your motor is not running and you’ve checked the following: for loose wiring connections, fuse, the switch on the lead wire was “ON” and made sure you were connected to a fully charged battery and everything is fine, but the motor won’t run, then it’s time to check to see if the pressure switch is bad.  Remove the cover off the 1” square box (pressure switch) on the head of the pump, the cover is held on by one phillips-head screw. This will expose the two red wires.
PAGE 4
Warranty LIMITED WARRANTY FOR NEW FIMCO EQUIPMENT WHO MAY USE THIS LIMITED WARRANTY. This limited warranty (the “Limited Warranty”) is provided by Fimco to the original purchaser (“you”) of the Equipment (as defined below) from Fimco or one of Fimco’s authorized dealers. This Limited Warranty does not apply to any subsequent owner or other transferee of the Equipment. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.