Desk PRODUCT GUIDE & ASSEMBLY INSTRUCTIONS
Should you prefer to speak with a customer service representative, you may call toll free: 1-855-372-2315 2
Guidelines FAILURE TO FOLLOW THESE WARNINGS WHEN IN USE COULD RESULT IN INJURY • Do not stand on the item or use as a step ladder • Do not use this item unless all bolts and screws are firmly secured and fastened. • Check all bolts and screws every 90 days. As necessary tighten if any are loose. • Lift up then move. Pushing over or dragging this product can result in an injury or cause damage to the floor and piece.
WARNING: DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF INJURY. Pre-Assembly Preparation: Please read through this instruction booklet before beginning assembly of this item. Two adults are recommended for assembly. • Clear out the space for assembly and lay out all parts on Parts List, extra room will allow you to easily determine if all the pieces are present. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
Parts List 1 1 Back Panel (1) 2 2 4 4 Bottom Panel (1) Left Upright Partition (1) 3 5 5 8 Desk Top (1) 6 Left Side Panel (1) 6 Right Upright Partition (1) Right Side Panel (1) 9 8 7 7 Shelf (1) 3 9 Bottom Rear Rail (1) 5
Parts List 10 10 Bottom Central Rail (1) 12 X2 11 11 Drawer Front Panel (1) 12 Drawer Side Panel (2) 15 X2 14 13 13 6 Drawer Back Panel (1) 14 Drawer Bottom Panel (1) 15 Side Leg (2)
Parts List A Wood Dowel (30) M8x25MM B Cam Lock (20) D15x11MM C Cam Bolt (20) M6x28MM D Cam Hole Cover (20) D:15MM E Small Screw (12) M3.
Parts List J Nail (8) M1.8x18MM K Handle (1) Length:100MM L Handle Bolt (2) M4x35MM CR CL DR DL M Handle Washer (2) M16x1MM N Allen Key (1) M4 Use a Allen Key to tighten the cam nuts. A quarter turn clockwise is all that is needed.
Step 1 1. Remove all parts from the carton and place them on a protected surface or carpet. 2. Check all parts and hardware against the “Parts List”. 3. Insert Wood Dowels (A) into the Back Panel (1), Shelf (2), Desk Top (3), Bottom Panel (4), Left Upright Partition (7), Right Upright Partition (8) and the Bottom Central Rail (10) as shown in the image below.
Step 2 1. Insert Cam Bolts (C) into the Desk Top (3), Bottom Panel (4), Left Side Panel (5) and Right Side Panel (6) and tighten with a screwdriver or electric screwdriver (not supplied) as shown in the image below.
Step 3 1. Attach the CL Runner (O) to the Left Upright Partition (7) with three M3.5x16MM Screws (E) and tighten with a screwdriver or electric screwdriver (not Supplied). Note: Use the CL mark on the CL Runner (O) to correctly attach to the Left Upright Partition (7) as shown below. 2. Attach the CR Runner (O) to the Right Upright Partition (8) with three M3.5x16MM Screws (E) and tighten with a screwdriver (not supplied).
Step 4 1. Attach two Drawer Side Panels (12) to the Drawer Back Panel (13) and Drawer Front Panel (11) with eight M4x38MM Screws (G) and tighten with a screwdriver (not Supplied) as shown below.
Step 5 1. Attach the Drawer Bottom Panel (14) to the assembled unit - unfinished side down and fasten with eight Nails (J) by hammer (not supplied) as shown below.
Step 6 1. Attach the DR and DL Runners (O) to the assembled drawer with six M3.5x16MM Screws (E) and tighten with a screwdriver as shown below.
Step 7 1. Attach the Handle (K) and Handle Washer (M) to the assembled unit with two Handle Bolts (L) and tighten with a screwdriver.
Step 8 1. Attach the Bottom Central Rail (10) to the Bottom Panel (4) and Insert four Cam Locks (B) into the Panel and tighten by using the Allen Key (N). 10 4 B N B Use a Allen Key to tighten the cam nuts. A quarter turn clockwise is all that is needed.
Step 9 1. Attach the Left Upright Partition (7) and the Right Upright Partition (8) to the Desk Top (3) and insert four Cam Locks (B) into the partitions (7) and (8) as shown below. Tighten by using the Allen Key (N).
Step 10 1. Attach the assembled Bottom Panel (4) to the assembled Partitions (7) and (8). 2. Use four M6 x 50MM Screws (I) and tighten with the Allen Key (N).
Step 11 1. Attach the Back Panel (1) to the assembled unit (3) as shown below. 2. Use eight M6 x 50MM Screws (I) and tightening with the Allen Key (N).
Step 12 1. Attach the Shelf (2) to the assembled unit as shown below. 2. Use four M6 x 50MM Screws (I) and tightening with the Allen Key (N).
Step 13 1. Attach the Left Side Panel (5) to the assembled unit. 2. Insert six Cam Locks (B) into the assembled unit as shown below and tighten with the Allen Key (N).
Step 14 1. Attach the Right Side Panel (6) to the assembled unit. 2. Insert six Cam Locks (B) into the assembled unit as shown below and tighten with the Allen Key (N).
Step 15 1. Attach the Side Leg (15) to the assembled unit with four M4x32MM Screws (F) and tighten with a screwdriver as shown below.
Step 16 1. Attach the Bottom Panel (9) to the Side Leg (15) with two M4 x 45MM Screws (H) and tighten with a screwdriver. 2. Attach the Leg (15) to the Bottom Panel (4) with four M4 x 32MM Screws (F) and tighten with a screwdriver.
Step 17 1. Place the Cam Hole Covers (D) on all Cam Lock Holes.
Step 18 1. Insert the drawer into the assembled unit as shown in diagram.
Periodically (every 90 days) inspect the screws to make sure they are still fully tightened. ATTENTION: Be certain that all screws are fully tightened before using this desk.
Product Dimension 19.6 9inc h 2inc 48.8 36.42inch (92.5cm) 28 (12 m) 4.0c h (5 0.
Limited Warranty The manufacturers products are warrantied against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as the party or entity which purchases this manufacturer’s furniture from an authorized retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned products.
