Data Sheet

ManualsBrandsFinder ManualsElectromechanicsTwilight switch output unit 1 pc(s) 19.91.9.012.4000 Operating voltage:12 V DC 1 change-over

1 CO (SPDT)

10/15

250/400

2,500

500

0.44

10/0.3/0.12

300 (5/5)

AgSnO

1 NO (SPST-NO)

300

(0.8…1.1)U

0.6 (50 Hz)/0.4

(0.8...1.1) U

1,000

–20…+50

IP 20

Contact specification

Contact configuration

Rated current/Maximum peak current A

Rated voltage/Maximum switching voltageV AC

Rated load AC1 VA

Rated load AC15 (230 V AC) VA

Single phase motor rating (230 V AC) kW

Breaking capacity DC1 (24/110/220 V) A

Minimum switching load mW (V/mA)

Standard contact material

Feedback contact specification (terminals B1-B2)

Contact configuration

Maximum current mA

Rated voltage V AC/DC

Supply & Input specification

Nominal voltage (U

) V AC (50/60 Hz)

VDC

Rated power VA (50 Hz)/W

Operating range AC

Technical data

Ambient temperature range °C

Protection category

Approvals (according to type)

19 Series - Override & Status indicating modules

Features

Auto/Off/On output module 10 A

• Auto/Off/On output module intended to

permit the automatic control of pumps, blowers

or motor groups. Or, in the case of installation,

maintenance or failure, to permit the load

equipment to be turned “Off“ or controlled

under “On“ control

• Ideal interface for PLC and electronic systems

• Only 11.2 mm wide

• 3 function selector switch:

- Auto: works as a monostable relay

(following A3 input)

- Off: relay permanently OFF

- On: relay permanently ON

• 24V AC/DC supply and module input

• 35 mm rail (EN 60715) mounting

Application examples:

• control of pumps, blowers or motor groups

• primarily suited to Industrial control systems

• 1 CO output contact

• 11.2 mm wide

• Feedback contact

19.21.0.024.0000

Wiring diagram

For outline drawing see page 11

B1-B2 feed back information to the controller for Auto-operation

A3-A2 From the controller requested operation

Auto-Operation

Intervention-(Manual-)Operation

Switch position:

Request

Response

LED Signals

Controller, PLC Type 19.21

VI-2012, www.findernet.com

Summary of content (14 pages)

PAGE 1
9 Series - Override & Status indicating modules Features 19.21.0.024.0000 Auto/Off/On output module 10 A Auto/Off/On output module intended to permit the automatic control of pumps, blowers or motor groups. Or, in the case of installation, maintenance or failure, to permit the load equipment to be turned “Off“ or controlled under “On“ control • Ideal interface for PLC and electronic systems • Only 11.
PAGE 2
19 Series - Override & Status indicating modules Features 19.31.0.024.0000 1-channel status indicating module 1-channel indicating module to provide visual indication of BMS/DDC/PLC input or output status with immediate indication of its importance or urgency according to the colour of the LED. A change-over output contact, following the input to the module, provides for further control or status feedback.
PAGE 3
19 Series - Override & Status indicating modules Features 19.32.0.024.0000 2-channel status indicating module 2-channel indicating module to provide visual indication of BMS/DDC/PLC input or output status with immediate indication of its importance or urgency according to the colour of the LED. Two NO output contacts, following the inputs to the module, provide for further control or status feedback.
PAGE 4
19 Series - Override & Status indicating modules Features 19.41.0.024.0000 Override module - Auto/Off/Hand Auto/Off/Hand override module intended to permit the automatic control of pumps, blowers or motor groups.
PAGE 5
19 Series - Override & Status indicating modules Features 19.42.0.024.0000 Override module - Auto/Off/Low/High Override output module intended to permit the automatic control of two-speed pumps, blowers or motor groups.
PAGE 6
19 Series - Override & Status indicating modules Features 19.50.0.024.0000 Analogue override module - Auto/Hand (0…10)V Analogue output module intended to provide, by the selection switch on the front panel, a (0…10) V output, automatically or by hand. With the selector switch in position “A“ (Automatic) the (0…10) V signal is derived from the controller.
PAGE 7
19 Series - Override & Status indicating modules Features 19.91.9.0xx.4000 Power relay module 16 A Suitable for Lamps load AgSnO2 contacts for heavy duty, high inrush current loads • DC supply (12 or 24 V) • LED indicator • Reinforced insulation between supply and contacts • Cadmium Free contacts • 35 mm rail (EN 60715) mounting • • • • 1 Pole changeover contact 17.
PAGE 8
19 Series - Override & Status indicating modules Ordering information Example: 19 series Auto/Off/Hand override module, 1 CO (SPDT) 5 A contact, 24 V AC/DC supply. 1 9 . 4 1 . 0 . 0 2 4 . 0 0 0 0 Contact material 0= Standard for 19.21/31/32/41/42/50 4= Standard for 19.91 Series Type 21= Auto/Off/On output module, 11.
PAGE 9
19 Series - Override & Status indicating modules Wiring diagrams - Application examples Type 19.21 Controller, PLC Type 19.21 End process Type 19.31 * LED Controller, PLC Type 19.31 End process * S can be, for example, a NO-contact with the purpose of indicating “in operation” (selecting green as LED color) or a NC-contact with the purpose of indicating “error” or “alarm” (selecting red or blue as LED color). The LED color has to be chosen through the back side selector. Type 19.32 VI-2012, www.
PAGE 10
19 Series - Override & Status indicating modules Wiring diagrams - Application examples Type 19.41 Controller, PLC Type 19.41 End process Type 19.42 End process Type 19.42 Controller, PLC Type 19.50 Output analog signal Input analog signal Controller, PLC Type 19.50 End process VI-2012, www.findernet.com In the selector position A (Automatic) the 0...10 V set point of Yin - A2 is leaded, through Yout, to the end process; in the selector position H (Hand) the 0...
PAGE 11
19 Series - Override & Status indicating modules Outline drawings Type 19.31-19.32 Screw terminal Type 19.41 Screw terminal Type 19.42 Screw terminal Type 19.50 Screw terminal Type 19.91 Screw terminal VI-2012, www.findernet.com Type 19.
PAGE 12
19 Series - Override & Status indicating modules Accessories Sheet of marker tags, for 19.21 type, plastic, 40 tags, 8x10 mm 019.40 Sheet of marker tags, for 19.31/32/41/42/50/91 types, plastic, 72 tags, 6x12 mm 060.72 Identification tag, for 19.31/32/41/42/50 types, plastic, 1 tag, 17x25.5 mm 019.01 Adaptor for panel mounting, for 19.31/32/41/50/91 types, plastic, 17.5 mm wide 020.01 019.40 060.72 019.01 020.01 Adaptor for panel mounting, for 19.42 type, plastic, 35 mm wide 011.
PAGE 13
19 Series - Override & Status indicating modules Application notes Intervention Modules The demand for security apparatus, heating, air conditioning or efficient energy use in offices, hotels, and private homes or in industrial space is growing constantly, leading to the installation of increasingly complex electronic systems.
PAGE 14