Datasheet

3
Copper side view Copper side view
Pin length 3,5 mm for PCB only Pin length 3,5 mm for PCB only
Pin length 5.3 mm for PCB or Pin length 5.3 mm for PCB or
sockets sockets
See ordering information See ordering information
VI-2014, www.findernet.com
40.31 40.61
1 CO (SPDT) 1 CO (SPDT)
12*/20 16/30
250/400 250/400
3,000 4,000
1,000 1,000
0.55 0.55
12/0.3/0.12 16/0.3/0.12
300 (5/5) 500 (10/5)
AgNi AgCdO
——
12 - 24 12 - 24
0.65/0.5 0.65/0.5
——
(0.73…1.5)U
N
/(0.73…1.5)U
N
(0.73...1.5)U
N
/(0.8…1.5)U
N
0.4 U
N
0.4 U
N
0.1 U
N
0.1 U
N
10 · 10
6
10 · 10
6
200 · 10
3
100 · 10
3
7/3 (10/3 sensitive) 7/3 (10/3 sensitive)
6 (8 mm) 6 (8 mm)
1,000 1,000
–40…+85 –40…+85
RT II** RT II**
Contact specification
Contact configuration
Rated current/Maximum peak current A
Rated voltage/Maximum switching voltage V AC
Rated load AC1 VA
Rated load AC15 (230 V AC) VA
Single phase motor rating (230 V AC) kW
Breaking capacity DC1: 30/110/220 V A
Minimum switching load mW (V/mA)
Standard contact material
Coil specification
Nominal voltage (U
N
) V AC (50/60 Hz)
V DC
Rated power DC/sensitive DC W
Operating range AC
DC/sensitive DC
Holding voltage DC
Must drop-out voltage DC
Technical data
Mechanical life cycles
Electrical life at rated load AC1 cycles
Operate/release time ms
Insulation between coil and contacts (1.2/50 µs) kV
Dielectric strength between open contacts V AC
Ambient temperature range °C
Environmental protection
Approvals (according to type)
• 3.5 mm contact pin pitch
• 1 Pole 12 A (on PCB; 10 A
with socket)
• PCB or 95 series sockets
Features
1 Pole relay range
40.31 - 1 Pole 12 A (3.5 mm pin pitch)
40.61 - 1 Pole 16 A (5 mm pin pitch)
• Pin length 3.5 mm for pcb mount
• Pin length 5.3 mm as Plug-in relay
• DC standard (0.65 W) or sensitive (0.5 W)
coils available
• Cadmium Free contact material available
• 6 kV (1.2/50 s) isolation coil-contacts
• 8 mm creepage and clearance distances
between coil and contacts
• Meets EN 60335-1 glow wire requirements
• Flux proof: RT II standard or wash tight RT III
• AC inductive load rating (related to AC15
utilisation category) 4 A 250 V approved
according to EN 61810-1:2008
(Annex B tables B1, B2, B3)
• 5 mm contact pin pitch
• 1 Pole 16 A
• PCB or 95 series sockets
* mounted on sockets ≤ 10 A
For outline drawing see page 10
** See general technical information “Guidelines for automatic flow solder processes” page II.
40 Series - Miniature PCB/Plug-in relays 8 - 10 - 12 - 16 A
40
SERIES
A