Use and Care Manual

23
SPECIFIC SAFETY RULES
a) If not used correctly and without suitable
maintenance, the stapler can cause serious injury.
b) Always wear goggles and ear plugs when using the
stapler.
c) Handle the stapler holding it firmly by the grip only.
d) Always disconnect the tool from the air supply
when unattended, performing any maintenance or
repair, clearing a jam, or moving the tool to a new
location. Do not load the tool with nails when either the
trigger is depressed or the Safety device (Fig. 24 - A) is
engaged. The tool could eject a nail causing death or
serious personal injury.
e) Always fit tool with a fitting or hose coupling on or near
the tool in such a manner that all compressed air in the
tool is discharged at the time the fitting or hose coupling is
disconnected. Do not use a check valve or any other fitting
which allows air to remain in the tool. Death or serious
personal injury could occur.
f) Never place hands or any other body parts in the
nail discharge area of the tool. The tool might eject a
nail and could result in death or serious personal injury.
g) Do not touch the trigger unless driving nails. Never
attach air line to tool or carry tool while touching the
trigger. The tool could eject a nail which will result in death
or serious personal injury.
h) Always assume the tool contains nails. Respect
the tool as a working implement; no horseplay. Always
keep others at a safe distance from the work area in case
of accidental discharge of nails. Do not point the tool
toward yourself or anyone whether it contains nails or not.
Accidental triggering of the tool could result in death or
serious personal injury.
i) Do not nail on top of another nail. This is able to
cause the nail to be deflected and hit someone, or cause
the tool to react and result in a risk of injury to persons.
j) Do not drop or throw the tool. Dropping or throwing
the tool can result in damage that will make the tool
unusable or unsafe. If the tool has been dropped or
thrown, examine the tool closely for bent, cracked or
broken parts and air leaks. STOP and repair before using
or serious injury could occur.
k) Always check that the safety device (A) is operating
properly. A nail could accidentally be driven if the safety
device (A) is not working properly. Personal injury may occur.
l) Disconnect air supply and release tension from the
trigger before attempting to clear jams because nails
can be ejected from the front of the tool. Personal injury
may occur.
m) Never use the stapler against metal or masonry
objects.
n) Never exceed the maximum operating pressure
indicated for this accessory.
WARNING:
Remove finger from the trigger when not driving
fasteners. Never carry the tool with finger on trigger, the
tool is able to fire a fastener.
Do not attach the hose or tool to your body. Attach
the hose to the structure to reduce the risk of loss of
balance if the hose shifts.
MULTIPURPOSE STAPLER
OPERATION
Technical data
Model No.: 9045783
Max. Operating Pressure: .................................... 100 PSI
Recommended Operating Pressure Range: ... 60-100 PSI
Air inlet: .............................................................. 1/4” NPT
Magazine capacity: ........................................ 100 staples
Firing mode:................................................ Sequential fire
Fastener Gauge: ........................................................... 21
Fastener Lengths: ............................................... ¼” - 5/8”
Staple size: ................................................ 0.048” x 0.022”
Uses Arrow® T50® type staples ........................................
LUBRICATION
Disconnect the stapler from the air supply.
Before using the stapler for the first time and after each use,
lubricate air inlet (E) of the stapler (Fig. 20). To lubricate,
insert 2-3 drops of lubricant. Using too much oil will cause it
to collect in the tool and be noticeable in the exhaust.
Under low use, lubricate once a day. Under heavy use,
lubricate twice a day.
TOOL TESTING
Before actually beginning the nailing work, test the tool by
using the check list below. Conduct the test in the following
order.
If abnormal operation occurs, stop using the tool and
performed by qualified repair personnel immediately.
E
WARNING:
An improperly functioning tool must not be used.
Do not actuate the tool unless the tool is placed firmly
against the work piece.
Fig. 20