Datasheet

ManualsBrandsFinisar ManualsNetworkingFTLF8524P2BNV

Product Specification

4.25 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver

FTLF8524P2xNy

PRODUCT FEATURES

 Up to 4.25 Gb/s bi-directional

data links

 Hot-pluggable SFP footprint

 Built-in digital diagnostic functions

 850nm Oxide VCSEL laser

transmitter

 Duplex LC connector

 RoHS Compliant and Lead Free

 Up to 500m on 50/125μm MMF,

300m on 62.5/125μm MMF

 Metal enclosure, for lower EMI

 Single 3.3V power supply

 Extended operating temperature

range: -20°C to 85°C

APPLICATIONS

 Tri-Rate 1.063/2.125/4.25 Gb/s

Fibre Channel

 1.25 Gb/s 1000Base-SX Ethernet

(Rate selectable version)

 Wireless – OBSAI, CPRI

Finisar’s FTLF8524P2xNy Small Form Factor Pluggable (SFP) transceivers are

compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)

They are compatible with Fibre Channel FC-PI-2 Rev. 7.0

. Rate Selectable versions are

also compatible with Gigabit Ethernet as specified in IEEE Std 802.3

. They are RoHS

compliant and lead-free per Directive 2002/95/EC

and Finisar Application Note AN-

2038. Digital diagnostics functions are available via the 2-wire serial bus specified in the

SFP MSA.

PRODUCT SELECTION

FTLF8524P2xNy

W Wide Extraction Bail

B Narrow Extraction Bail

L Non Rate Selectable - 1x, 2x, 4x Fibre Channel

V Rate Selectable - 1x, 2x, 4x Fibre Channel and Gigabit Ethernet

Summary of content (12 pages)

PAGE 1
Product Specification 4.25 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver FTLF8524P2xNy PRODUCT FEATURES Up to 4.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions 850nm Oxide VCSEL laser transmitter Duplex LC connector RoHS Compliant and Lead Free Up to 500m on 50/125μm MMF, 300m on 62.5/125μm MMF Tri-Rate 1.063/2.125/4.25 Gb/s Fibre Channel Metal enclosure, for lower EMI Single 3.3V power supply 1.
PAGE 2
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 I. Pin Descriptions Pin 1 2 3 4 5 6 7 Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select 8 9 10 11 12 13 14 15 16 17 18 19 20 LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID.
PAGE 3
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Symbol Vcc TS TA RH Min -0.5 -40 -20 0 Typ Max 4.0 85 85 85 Unit V °C °C % Ref. 1 Electrical Characteristics (TA = -20 to 85 °C, VCC = 3.0 to 3.
PAGE 4
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 IV. Optical Characteristics (TOP = -20 to 85 °C, VCC = 3. 00 to 3.60 Volts) Parameter Transmitter Output Opt. Pwr: 50 or 62.5 MMF Optical Wavelength Spectral Width Optical Modulation Amplitude @ 4.25 Gb/s Optical Modulation Amplitude @ 2.125 Gb/s Optical Modulation Amplitude @ 1.0625 Gb/s Optical Rise/Fall Time Relative Intensity Noise Deterministic Jitter Contribution @ 2.125 Gb/s Deterministic Jitter Contribution @ 4.
PAGE 5
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 10. Measured with conformance signals defined in IEEE 802.3 specifications. 11. Rate Selectable version in low bandwidth mode. 12. Rate Selectable version in high bandwidth mode. V. General Specifications Parameter Data Rate Symbol BR Bit Error Rate Fiber Length on 50/125μm MMF Min Typ 1.062, 1.25, 2.125, 4.25 10-12 550 300 150 300 150 70 BER L L Fiber Length on 62.5/125μm MMF Max Units Gb/sec m m Ref. 1 5 2 3 4 2 3 4 Notes: 1.
PAGE 6
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 VIII. Digital Diagnostic Functions Finisar FTLF8524P2xNy SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
PAGE 7
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 IX. Digital Diagnostic Specifications FTLF8524P2xNy transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics.
PAGE 8
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 X. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA). FTLF8524P2BNy © Finisar Corporation Jun 25, 2009 Rev.
PAGE 9
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 FTLF8524P2WNy © Finisar Corporation Jun 25, 2009 Rev.
PAGE 10
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 XI. PCB Layout and Bezel Recommendations © Finisar Corporation Jun 25, 2009 Rev.
PAGE 12
FTLF8524P2xNy Pluggable SFP Product Specification – June 2009 XII. References 1. Small Form-factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000. 2. “Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev. 7.0)”. American National Standard for Information Systems. 3. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-SX. IEEE Standards Department, 2002. 4.