OPERATION AND PARTS MANUAL DRUM PUMPS AND MOTORS HVDP SERIES 1
TABLE OF CONTENTS Introduction........................................................................................................................................................................3 Warranty.............................................................................................................................................................................3 Chemical Reaction Disclaimer....................................................................................................
INTRODUCTION Finish Thompson is a designer and manufacturer of drum pumps and mixers available worldwide through a qualified, experienced network of distributors and/or representatives. Drum pump selection is easy with FTI’s complete line of interchangeable motors and tubes. WARRANTY Finish Thompson Inc (manufacturer) warrants this product to be free of defects in materials and workmanship for a period of one year from date of purchase by original purchaser.
SAFETY PRECAUTIONS ALWAYS read the installation instructions before operating the pump. ALWAYS wear protective clothing, eye protection and follow standard safety procedures when handling corrosive or personally harmful materials. Always use protective gloves to prevent contact with hot surfaces. NEVER use an open, splash proof or TEFC motors when pumping or mixing flammable or combustible material. ALWAYS place the pump intake in fluid before starting the pump.
HVDP TERMINOLOGY 5
HVDP SERIES ASSEMBLY, MAINTENANCE & CLEANING INSTRUCTIONS Section 1: Motor Installation and Removal INSTALLATION - HVDP-HR 1. Locate the rubber coupling insert that was separately shipped in a plastic bag (see Figure 1). 2. Install the rubber coupling insert onto the metal coupling half located on top of the HR drive assembly. 3. Find the metal coupling half located inside the HR motor. Align this coupling with rubber insert installed in the second step of these instructions. 4.
Section 2: Stator Removal, Inspection, and Installation Removal: 1. The stator is located at the bottom of the pump tube assembly (see Figure 5). 2. Remove the stator by unthreading it from the pump tube. If the stator cannot be unthreaded by hand, insert a screwdriver into the slots found at the bottom of the stator. Use the screwdriver to rotate the stator. Pump Tube Assembly Note: The stator has left hand threads. Inspection: Inspect the stator for gouging and excessive wear.
Figure 4 Section 4: Rotor Removal, Inspection, and Installation Removal: 1. Remove the motor (see section 1 and follow the instructions for your model). 2. Remove the drive assembly (see section 3). 3. The rotor is located at the bottom of the drive assembly (see Figure 4). 4. Using 3/4” and 5/8” open-end wrenches, loosen and remove the rotor. Inspection: Inspect the rotor for excessive wear and deep grooving. Contact FTI if you are questioning the condition of the rotor.
HVDP SERIES - HVDP-HR ITEM 1 2 3 3 3 3 4 4 4 4 4 4 5 5 5 6 6 6 7 7 7 7 DESCRIPTION PART NUMBER Coupling Insert J100014 HVDP-HR Gear Box Assembly 16:1 105150 Tube O-ring FKM 105080 Tube O-ring EPDM 105081 Tube O-ring Buna-FDA 108069 Tube O-ring PTFE Encap Sil 105082 Seal (carbon/ceramic/FKM) J102957-1 Seal (carbon/ceramic/EPDM) J102957-2 Seal (carbon/ceramic/Buna-FDA) 108073 Seal (carbon/ceramic/Kalrez) J103081 Seal (silicon carbide/FKM) J103066 Seal (silicon carbide/EPDM) J103067 HVDP 27 HR Shaft Assembly
HVDP SERIES - HVDP-LR ITEM 1 1 2 2 2 2 3 3 3 3 3 3 4 4 4 5 5 5 6 6 6 6 DESCRIPTION HVDP LR Gearbox Assembly 5:1 HVDP LR Gearbox Assembly 4:1 Tube O-ring FKM Tube O-ring EPDM Tube O-ring Buna-FDA Tube O-ring PTFE Encap Sil.
M58H & M59H 800W MOTORS Item 1 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 15 16 17 Quantity M58 M59 1 2 1 1 1 2 6 6 3 1 1 1 1 1 1 1 1 2 1 1 1 2 6 6 3 1 1 1 1 1 1 1 11 Description Part Number Housing Repair Kit Ball Bearing Switch Half Coupling Cord Assembly Cord Assembly Brush Set Housing Nut Housing Bolt Screw Wave Washer Circuit Breaker Circuit Breaker Cover Fan Speed Control Speed Control Speed Control Knob Gearbox Adapter 105144 J101069 J101143 J100013 A101738 A101740 J101107 J100990 J100023 J101530
EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the applicable health and safety requirements as specified be the EC Directives listed. The product may not be taken into service until it has been established that the drive motor for the Drum and Container Pump complies with the provisions of all relevant EC Directives.
