PF SERIES PUMPS PFS OPERATION & PARTS MANUAL For Serial Number 162859 & above
EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the applicable health and safety requirements as specified be the EC Directives listed. The product may not be taken into service until it has been established that the drive motor for the Drum and Container Pump complies with the provisions of all relevant EC Directives.
Introduction This manual pertains to the PF Series, specifically the PFS stainless steel drum pump. Finish Thompson Inc. thanks you for choosing our products. We believe the use of our products will be fully satisfactory. When properly installed and operated, your Finish Thompson motor and pump will provide long, trouble-free service; therefore, please read this manual carefully before carrying out any operations on the pump/motor unit.
Warranty, General Terms & Conditions 1. The following terms and conditions apply to the sale of machinery, components and related services and products, of Finish Thompson Inc. (hereinafter “the products”) 2. Finish Thompson Inc. (the manufacturer) warrants only that: a) its products are free of defects in material, design and workmanship at the time of original purchase; b) c) its products will function in accordance with Finish Thompson Inc. operation manuals; Finish Thompson Inc.
Safety 1. Introduction This manual contains all the information needed for the correct installation, use and maintenance of your new Finish Thompson pump. It should be read and understood by all the personnel involved in installation, operating and servicing of the pump before it is started. 2. Operator Qualification and Training The personnel in charge of the installation, the operation, and the maintenance of the pump must be qualified and able to perform the operations described in this manual.
PUMP SPECIFICATIONS MODEL PFS Outer Tube Diameter Discharge Type 2” (51 mm) 1” hose barb with variable orifice (1-1/4” NPSM without variable orifice & nut) Max. Specific Gravity 1.83 Max. Viscosity 2000 cP Min./ Max. Fluid Temperature -20°F with FKM or buna o-rings (5° F with Perlast o-rings) Min. / 220° F Max. Wetted Materials 316 Stainless Steel, FKM (optional Perlast or buna-FDA), PTFE, ETFE -4° C with FKM or buna o-rings (21° C) Min. / 105° C Max.
Installation & Maintenance Instructions Installation 1. Remove the drum pump and motor from its packaging and inspect for shipping damage. 2. Turn the pump coupling to verify there is no binding. Verify the housing cover (item 16) is on tight (it has a left hand thread. 3. Adjust the coupling so that the empty slots in the insert are at 3 and 9 o’clock with the pump discharge at 12 o’clock. 4. Install the motor according to instructions in the appropriate motor manual. 5. Attach 1” i.d.
Reassembly 1. Install new lip seal (item 4) into the pump head with the grooved side facing the bottom of the pump. 2. If bearing assembly is replaced -- thread the shaft (item 14) into the bearing assembly (item 3) with the 3/32 hole in the shaft on the other end. Carefully insert the shaft straight through the lip seal (to avoid seal damage) from the top and seat the bearing assembly (item 3) into the pump head. 3. If o-rings are replaced -- install 2 inner tube o-rings (item 8) in the grooves.
PFS SPARE PARTS EXPLODED VIEW 7
PUMP SPARE PARTS LIST ITEM 1 QTY 1 2 1 3* 1 4* 1 5 1 6 1 7 1 8* 2 9 1 10* 1 11* 1 12* 1 13† 1 14 1 15 1 † 16 1 DESCRIPTION PART NUMBER COUPLING INSERT J100014 COUPLING HALF J100012 BEARING ASSEMBLY A101110 LIP SEAL 1/4” FKM LOCK WASHER #8 BRASS SCREW #8-32 X 1/4 BRASS PAN HEAD INTAKE TUBE ASSEMBLY 27” MODELS 40” MODELS 48” MODELS 60” MODELS 72” MODELS INNER TUBE O-RING FKM EPDM BUNA PERLAST STAINLESS STEEL INNER TUBE 27” MODELS 40” MODELS 48” MODELS 60” MODELS 72” MODELS P
