EF SERIES MOTORS OPERATION & PARTS MANUAL Models S1, S2, S3, S4 S1, S2, S3 S4
EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following motors fully comply with the applicable health and safety requirements as specified be the EC Directives listed. This declaration is valid provided that the devices are fully assembled and no modifications are made to these motors.
Introduction This manual pertains to S Series drum pump motors. Finish Thompson Inc. thanks you for choosing our products. We believe that the use of our products will be fully satisfactory. When properly installed and operated, your Finish Thompson motor and pump will provide long, trouble-free service; therefore, please read this manual carefully before carrying out any operations on the pump/motor unit. Any use other than that described herein is considered incorrect; consequently, Finish Thompson Inc.
Warranty, General Terms & Conditions 1. The following terms and conditions apply to the sale of machinery, components and related services and products, of Finish Thompson Inc. (hereinafter “the products”) 2. Finish Thompson Inc. (the manufacturer) warrants only that: a) its products are free of defects in material, design and workmanship at the time of original purchase; b) c) its products will function in accordance with Finish Thompson Inc. operation manuals; Finish Thompson Inc.
Safety 1. Introduction This manual contains all the information needed for the correct installation, use and maintenance of your new Finish Thompson motor. It should be read and understood by all the personnel involved in installation, operating and servicing of the pump before it is started. 2. Operator Qualification and Training The personnel in charge of the installation, the operation and maintenance of the pump/motor must be qualified and able to perform the operations described in this manual.
INSTALLATION 1. Unpack motor and pump tube from carton. Check for shipping damage. If damage is detected, save the packaging and notify the carrier immediately. 2. If motor and pump tube are boxed separately, the motor will need to be fastened to the pump tube. See figures 1 & 2. Figure 1 Figure 2 3. Place the motor upside down on a tabletop surface with the coupling facing upwards and place the yellow coupling insert (item 1 from the pump manual) onto the motor’s coupling. See figures 3 & 4.
OPERATION Electric motor - Check that the motor switch is in the center “O” OFF position, and then plug the power cord into an outlet. Insert the pump tube into the fluid to be dispensed and the discharge hose into the container to be filled. While holding the motor handle and hose, switch the motor to the “I” low speed. The fluid will begin to pump. If more flow is desired, switch the motor to the “II” high speed setting. See figure 9 below.
MOTOR SPECIFICATIONS SPECIFICATIONS Nominal Voltage Hertz Rated Amps Input Power Duty Cycle RPM (low / high speed) Max. Flow Max. Head ELECTRIC MOTORS (2 SPEED) MODEL S1 MODEL S2 MODEL S3 115 Volts 230 Volts 115 Volts 60 50/60 50/60 2.0 Amps 1.1 Amps 2.0 Amps 1/3 HP (230 Watts) 250 Watts 230 Watts Continuous Continuous Continuous 8,000 / 14,000 8,000 / 14,000 8,000 / 14,000 17.0 GPM (64 l/m) 17.0 GPM (64 l/m) 17.0 GPM (64 l/m) 20 Ft. (6M) 20 Ft. (6M) 20 Ft. (6M) Max.
PARTS LIST – ELECTRIC MOTORS Models S1, S2 & S3 4 6 5 3 7 2 8 1 10 9 11 12 ITEM QTY DESCRIPTION PART NUMBER MODEL S1 MODEL S2 MODEL S3 1 1 115V US CORD 107215 N/A N/A 1 1 230V EU CORD N/A 107216 N/A 1 1 115V UK CORD N/A N/A 107216-1 2 1 TRIAC ASSEMBLY - 115V 107265-1 N/A 107265-1 2 1 TRIAC ASSEMBLY - 230V N/A 107265-2 N/A 3 1 ON/OFF SWITCH 107304 107304 107304 4 1 CIRCUIT BREAKER COVER J100789 J100789 J100789 5 1 CIRCUIT BREAKER - 115v 107326 N/
PARTS LIST - AIR MOTOR Model S4 MODEL S4 PARTS LIST ITEM QTY DESCRIPTION 1 1 AIR MOTOR ONLY J100032 2 1 AIR MOTOR ADAPTER 107073 3 1 COUPLING HALF J103934 4 1 NIPPLE J100107 5 1 HEX REDUCER BUSHING J100057 6 1 BALL VALVE J100073 7 1 UNION - BRASS J100036 8 2 SET SCREW J100040 9 1 MUFFLER J100033 N/S 1 AIR MOTOR REPAIR KIT J100060 N/S 1 OPTIONAL - FILTER / LUBRICATOR A100003 N/S 1 COUPLING INSERT J103422 N/S - NOT SHOWN Tech Service 1-800-888-3743 techserv
