S Series Motors Model S6* Operation & Parts Manual For EF Series Pump Tubes Only Patent pending.
EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following electrical equipment fully complies with the applicable health and safety requirements as specified be the EC directives listed. The product may not be taken into service until it has been established that the driven Drum and Container Pump complies with the provisions of all relevant EC Directives provided pumps manufactured by Finish Thompson are used.
Introduction This manual pertains to the S6 rechargeable drum pump motor. Finish Thompson, Inc. thanks you for choosing our products. We believe that the use of our products will be fully satisfactory. When properly installed and operated, your Finish Thompson motor and pump will provide long, trouble-free service; therefore please read this manual carefully before carrying out any operations on the pump-motor unit.
Warranty, General Terms & Conditions 1. The following terms and condition apply to the sale of machinery, components and related services and products, of Finish Thompson, Inc. (hereinafter “the products”) 2. Finish Thompson, Inc. (the manufacturer) warrants only that: a.) its products are free of defects in material, design and workmanship at the time of original purchase; b.) its products will function in accordance with Finish Thompson, Inc. operation manuals; Finish Thompson, Inc.
Safety Lithium Ion Battery Advantages The advanced lithium ion batteries contained in the S6 drum pump motor have several major advantages compared to older technologies like nickel cadmium (NiCd) or nickel metal hydride (NiMH). • They have much higher energy density compared to NiCd or NiMH. This results in a significantly lighter battery. The battery used in the S6 is extremely powerful for its compact size and weight. • Lithium ion batteries have no “memory” effect.
Operation Information • Warning- Do not use or charge this motor in hazardous locations where flammable vapors or ignitable dust occur. • The battery pack is not fully charged in a brand new motor. Fully charge the battery before the first use. • The recommended ambient temperature range for operating the motor is 40º F (4.5º C) to 105º F (40.5º C). Operating the motor below 40º F (4.5º C) will result in reduced battery capacity. • Never place metal objects in the motors charging port.
Noise Level S6 Rechargeable Motor in normal operating conditions produces a sound level equal to or less than 64 dBA at a distance of three feet (~ one meter). Modifications and Spare Parts Any changes concerning the service of the motor as originally purchased can be executed only after written approval from Finish Thompson, Inc. It is recommended to use only genuine Finish Thompson, Inc. spare parts and approved accessories.
Motor Operation Note: The motor has been partially charged and should be fully charged prior to use. Warning: The motor is NOT suitable for hazardous locations or pumping flammable or combustible materials. 1. Verify that the motor switch is in the center “O” OFF position. See Figure 6. Figure 6 2. Insert the pump tube into the fluid to be dispensed and the hose in the container to be filled. 3. While holding the motor handle and hose, switch the motor to the “I” low speed. The fluid will begin to pump.
Battery Pack Removal for Recycling If your battery pack will no longer hold a charge, you can either purchase a replacement battery pack or a new S6 motor assembly. To recycle your old battery pack, please follow these instructions: 1. Make sure the motor switch is in the OFF position before beginning. 2. Remove the 6-high-low screws (item 5) from the motor cover (item 1) & lift off. See Figure 8. 3. Remove red & black motor lead wires from the motor terminals one at a time. See Figure 9.
Wall Hanger Instructions Figure A Figure B If you ordered the optional Wall Hanger p/n 108287 or received it in one of our kits please follow these instructions for installation & use: 1. If using the 115v or 230v Quick Charger you may store it inside the Wall Hanger. Simply align the charger cables with the slots on the wall hanger making sure the indicator light lines up with the hole on the front of the wall hanger. Slide the charger into place.
Technical Data Motor Specifications Rechargeable Motor (2 speed) Specifications Model S6 Full Speed 12 12 volts* (10.8 volts) Battery Capacity/Type 3,200 mAh/Lithium Ion Input/Output Power 150/100 Watts Duty Cycle Continuous RPM (low/high speed) 8,000/12,000 2 14 gpm(53 lpm) @ high speed 0 Head - ft.
Item 1 1A 1B 1C 1D 1E 1F 2 3 4 4A 4B 4C 4D 5 Quantity 1 1 1 1 1 1 1 1 2 1 2 2 2 1 6 Description Motor cover & fan assembly Flammables warning label Switch Jack cover Jack nut DC power jack Stainless steel flat washer Battery pack assembly Flag terminal Motor & canister assembly Stainless steel flat washer Stainless steel lock washer Stainless steel socket head cap screw Hole plug Stainless steel hi-low screw Part Number 108301 108148 107304 108219 108220 107958 107974 108302 107972 108300 107125 107141 1
