TT SERIES PUMPS TTS, TTC, & STTS OPERATION & PARTS MANUAL
EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the applicable health and safety requirements as specified be the EC Directives listed. The product may not be taken into service until it has been established that the drive motor for the Drum and Container Pump complies with the provisions of all relevant EC Directives.
Introduction This manual pertains to the TT Series drum pumps. Finish Thompson Inc. thanks you for choosing our products. We believe the use of our products will be fully satisfactory. When properly installed and operated, your Finish Thompson motor and pump will provide long, trouble-free service; therefore, please read this manual carefully before carrying out any operations on the pump/motor unit. Any use other than that described herein is considered incorrect; and, consequently, Finish Thompson Inc.
Warranty, General Terms & Conditions 1. The following terms and conditions apply to the sale of machinery, components and related services and products, of Finish Thompson Inc. (hereinafter “the products”) 2. Finish Thompson Inc. (the manufacturer) warrants only that: a) its products are free of defects in material, design and workmanship at the time of original purchase; b) its products will function in accordance with Finish Thompson Inc. operation manuals; Finish Thompson Inc.
Safety 1. Introduction This manual contains all the information needed for the correct installation, use and maintenance of your new Finish Thompson pump. It should be read and understood by all the personnel involved in installation, operating and servicing of the pump before it is started. 2. Operator Qualification and Training The personnel in charge of the installation, the operation, and the maintenance of the pump must be qualified and able to perform the operations described in this manual.
PUMP SPECIFICATIONS Outer Tube Diameter Discharge Thread MODEL TTS MODEL TTC MODEL STTS 1-1/2” (3.8 cm) 1-5/8” (4.1 cm) 1-1/2” (3.8 cm) 1” hose barb 1” hose barb 1” hose barb 1.8 1.8 1.8 2000 cP 2000 cP 2000 cP Max. Specific Gravity Max. Viscosity Min./ Max. Fluid Temperature -20°F Min. to 150°F Max. 34°F Min. to 150°F Max. -10°F Min. to 150°F Max. (-29°C Min. to 66°C Max.) (1.1°C Min. to 66°C Max.) (-23°C Min. to 66°C Max.
Installation & Maintenance Instructions Installation 1. Remove the drum pump and motor from the packaging and inspect for shipping damage. Turn the pump coupling the mating motor coupling to verify there is no binding. 2. Adjust the drum pump coupling so that the empty slots in the insert are at 3 and 9 o’clock with the drum pump discharge at 12 o’clock. 4. Install the motor according to instructions in the appropriate motor manual. 5. Attach discharge hose and secure with hose clamp. 6.
Inspection 1. Inspect the shaft locating hole in the center of the bottom bearing (item 13 on the TTS/TTC and 16 on the STTS. If the inside diameter is .400 or larger than replace it. 2. Visually check the all the compressors (item 9 on TTS/TTC and item 12 on STTS) for damage. If they need replaced, you must remove the pin first. 3.
TTC/TTS SPARE PARTS EXPLODED VIEW 7
STTS SPARE PARTS EXPLODED VIEW 8
TTS/TTC SPARE PARTS LIST ITEM QTY 1 1 2 1 3* 1 4* 1 5 1 6 1 7 1 8 1 9* 4 10 2 11 1 12* 1 13* 1 DESCRIPTION PART NUMBER COUPLING INSERT J100014 COUPLING HALF J100013 BEARING ASSEMBLY W/ ROLL PIN SEAL ASSEMBLY PTFE (TTS) LOCK WASHER #8 BRASS (TTS) SCREW #8-32 X 1/4 BRASS PAN HEAD M/S INTAKE TUBE ASSEMBLY 27” 316 STAINLESS STEEL (TTS) 40” 316 STAINLESS STEEL (TTS) 48” 316 STAINLESS STEEL (TTS) 27” CPVC (TTC) 40” CPVC (TTC) 48” CPVC (TTC) IMPELLER ASSEMBLY PTFE WITH STAINLESS STEEL
STTS SPARE PARTS LIST ITEM QTY 1 1 2 1 3* 1 4* 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12* 1 13 1 14 1 15* 1 16* 1 DESCRIPTION PART NUMBER COUPLING INSERT J100014 COUPLING HALF J100013 BEARING ASSEMBLY WITH ROLL PIN A101672 SEAL ASSEMBLY FDA COMPLIANT PTFE 108401 UNION NUT 316 STAINLESS STEEL J100083 BEARING HOUSING 316 STAINLESS STEEL M100078 UNION NUT GASKET FDA APPROVED NEOPRENE J100084 LOCK WASHER #8 BRASS J100823 SCREW #8-32 X 1/4 BRASS PAN HEAD M/S J100822 INT
