AlbaBird FPV User Manual Fin inghobby Finwinghobby WWW . FINWINGHOBBY .
Please read through the manual before installation and flying This manual as introductions to user on how to build ing this RC plane. Please visit the www . finwinghobby . com official website for more introductions. Warning: 1 . This model airplane is not a toy , not recommended for children under 14 years old , 2.
CG . A B C CG . Area Main wing CG . Setting introductions : Green area C After lots of testing concluded CG . must be in the Green Area Point B : For safety purpose recommend Maiden flight use Point B Point A : if plane assemble correctly , we found that A is the best Different people measuring differently by fingers Moving CG . backward a little ( 3mm ) if plane pitch down tendency Moving CG . forward a little ( 3mm ) if plane pitch up tendency if still not good after CG .
Special Recommendations We have solved potentional problem s by new desgin and improving Mould making but what ever in case we still introduce this for your reference In case nose heavy: plane still nose heavy diving a lot even if CG . is at Point B Solutions : Elevator up approximately 1 . 5MM travel as following picture CG .
Airframe Building Pleae do to building as per instructions as below step by step 1 2 Glue vertical wing Install properly and drying Glue Fuselage Note : Don't install wings and other devices until drying at least 12 hours Finwinghobby .
Detachable Fuselage Non - detachable fuselge please skip to next page Fuselage Nut Fuselage tail - boom Finwinghobby .
Airframe Building 3 Plywood plywood reinforcements Detachable fuselge must install rods Standard Non - Detachable fuselge no need to install rods , please skip to next page Finwinghobby .
Airframe Building We can build main - wing now , let fuselage glue drying 4 Glue motor mounts Reminder with this remarks to the right wing Right wing Left wing Carbon strip Glue properly to the red area drying one minutes then install properly to the main - wing Finwinghobby .
Airframe Building 5 Glue tail - boom Reminder:must drying at least 1 hour before continuing to step 6 ( Detachable Fuselage please skip） 6 Glue tail - boom to fusealge Reminder : must let fuselage drying at least 12 hours this is very important , otherwise may cause horizontal wing wrongly pitch up Finwinghobby .
Airframe Building ( Detachable fuselage please skip） Let it stand up like this drying 12 hours 2020 Newly added this plywood For Non - Detachable fuselage < No need for detachable fuselage > Gule to fuselage for reinforcement 40 * 25MM 40 * 25MM Ground Finwinghobby .
9 + 2 Connector Male Female No regular rules on how to solder wires do as per your requirements freely Female to Wings Male to fuselage Screws secured Male connector to fuselage Screws for Female Connector Https :// www . fiwninghobby .
Standard 9PIN Connector 9PIN Female 9PIN Male ( Male to Fuselage , Female to Wing ) There is no regular wire connection , Please do according to your devices ' wires as below just for your reference ( Aileron ) ( Aileron ) ( TX ) ( TX ) ( ESC ) ( ESC ) ( ESC )( ESC ) ( VTX ) ( VTX ) ( To Main - wing ) ( To Fuselage ) Finwinghobby .
Standard 9PIN Connector Reminder : Correct Orientation Finally secured by screws Finwinghobby .
Motor , ESC , Servo Screw color silvery or Black 3CM 3CM Wires Length 3 . 0 CM Finwinghobby .
Motor , ESC , Servo Servo Horn Screw Big one Screw Smaller one Horizontal wing UP Finwinghobby .
New Servo Horn introductions Orders after July 2020 will use this new servo horn Newly upgraded Servo Horn Use Left Screw to secure the push rod Right Screw was fixed don ' t screw off Front 2 . 6 * 8 Rear 2 . 0 * 6 This is old one before upgrading Old one New One WWW . Finwinghobby .
Motor , ESC , Servo Main - wing Rudder Finwinghobby .
9 + 2 Building Wires length required 16CM Stock PNP servo wire is long enough Figure out proper wire length for your devices soldering to the 9 + 2 connector directly ESC Power wires recommend 18AWG is fine Https :// www . fiwninghobby .
9 + 2 Building Servo VTX ESC Motor Show in the manual is for you reference only you can do as per your preference Motor Antenna RX ESC Servo Https :// www . fiwninghobby .
9 + 2 Building Finished male ready to install to fuselage Shrink film or Hot Melt Glue to prevent it from loosing RX VTX Aileron wires in Parallel Two ESC Signal Wires in Parallel You can solder all devices and wires before installing to fus e l a ge Because it is removable freely , c onnector could be installed from inside instead of outside Https :// www . fiwninghobby .
How to install Motors and Propellers 1 > Propeller running inward 2 > Left CW Right CCW 3 > Propeller ' s Character forward CW CCW Tie screw like this if you are afraid of missing screws WWW . Finwinghobby .
