Manual

ManualsBrandsFire-Lite ManualsEquipmentBG-12LOB Manual Pull Station

BG-12LO/-12LOB Manual Pull Station

(Listed for Outdoor Applications)

Document 51378 Revision A ECN 00-215 06/16/2000

Description

The BG-12LOB Pull Station is a non-coded manual pull station

which provides a Fire Alarm Control Panel (FACP) with a single

alarm initiating input signal. The pull station is a dual action

model equipped with a key lock reset, an approved outdoor

gasket, and an accompanying outdoor backbox. It is UL listed

and meets the ADA requirement of a 5-lb. maximum pull down

force to activate. Operating instructions are molded into the

handle. Molded terminal numbers can also be found adjacent

to the wiring terminals.

Door ‘keys’ into

backplate at this point

12LAdoormount.wmf

1. Position the door and backplate side

by side in the full open position. (i.e.

180-degrees with respect to each

other.)

2. With the backplate position fixed,

move the door behind the backplate,

as shown in the illustration, part A.

3. Align the hinge posts and holes by

bringing the door up to meet the

backplate, paying particular attention

to the ‘keying’ that occurs when the

door’s post hole is aligned to the

backplate’s hinge post. Refer to the

illustration, part B.

4. With the two pieces aligned and

‘keyed’ together, slide the holes

down onto the posts. Refer to the

illustration, part C.

5. Holding the backplate, close the door

slightly to lock the door and backplate

together.

BG-12LOB

The features of the pull station include Dual-Action operation,

Key-Lock Reset function, Screw Terminal Wire connections,

outdoor use gasket, a WBB outdoor approved 4-inch backbox,

and a sealed switch with gold-plated switch contacts.

Note: The BG-12LOB is applicable with the WP-10 backbox

in retrofit applications. To meet UL requirements for outdoor

use, the BG-12LO Pull Station must be mounted to the WBB or

WP-10 Backbox to create the BG-12LOB model.

Switch Contact Rating

FACP Circuit (Terminals 1 & 2):

Rated to .25 Amp at 30 Volts (AC or DC).

Door Attachment

If the door becomes detached, complete the following steps to

reattach the door to the backplate. The door cannot be connected

to the pull station if the unit is mounted to a backbox.

Dual Action BG-12LOB

BG12LOBface.wmf

With the door and backplate

aligned and ‘keyed’ together,

slide the holes down onto the

posts.

Closing the door slightly

locks the door and

backplate together.

Door mated to Backplate

at this stage.

Post

Product ID

Label

Product ID

Label

Hole

Post

Hole

Post

Summary of content (2 pages)

PAGE 1
Description The BG-12LOB Pull Station is a non-coded manual pull station which provides a Fire Alarm Control Panel (FACP) with a single alarm initiating input signal. The pull station is a dual action model equipped with a key lock reset, an approved outdoor gasket, and an accompanying outdoor backbox. It is UL listed and meets the ADA requirement of a 5-lb. maximum pull down force to activate. Operating instructions are molded into the handle.
PAGE 2
From FACP IDC 1234 1234 1234 1234 1234 1234 1234 1234 1234 1234 To Next Device 1234 1234 1234 1234 IDC 1234567 1234567 1234567 Outdoor Stations Install the BG-12LO with a listed, outdoor-approved backbox (WBB or WP-10) to meet UL requirements for outdoor use. Without one of these backboxes, the BG-12LO is not listed for outdoor applications. Use the four supplied 8-32 x .375" mounting screws to attach the Pull Station to the outdoorapproved backbox. 12LOBmount.