Specifications Guide

54
X= Notch
Y= Total
counter-top
overhang
(Counter-top)
(Control
panel)
(Overhang)
X
Y
Clearance
12
12
12
11½
11½
11½
24¼
19¼
14
14
25
25
23½
36¾
25
14¼
22¾
19
18¾
14
22¾
22¾
11½
14
14¼
8¾
18
41½
20½
16½
29½
14
9½
12¾
24
20
24½
21¾
34½
24½
15¼
34⅛
20
34
25¼
14½
20½
20½
20½
20½
14½
21
30½
20½
31
13
20½
20½
w
h
w
w
h
h
12¾
5
14½
23⅜
12¾
Trash Container
• 53825-T
Outdoor Rated Kegerator (shown)
• 3594-DR (DL)
Outdoor Rated Refrigerator
• 3589-DR (DL)
Refrigerator (shown)
• 3598
Refrigerator with
stainless steel door
• 3598-DR (DL)
Black Diamond Edition
• 3598H-DR (DL)
Large Capacity
Ice Maker
∞
• 3597
Legacy Single Access Door
w/Tank Tray & Louvers
• 23920-1T-S
Legacy Single Door
w/Dual Drawers
• 23820-S
Legacy Double Doors with
Dual Drawers & Trash Tray
• 23930S-12
Legacy Masonry Drawer
• 23830-S
Legacy Single Access Door
with Louvers
• 23920-1-S
Horizontal Single
Access Doors
(D)
Vertical Single
Access Doors
(E)
Double
Access Doors
(F)
Louvered
Venting Panel
• 5510-01
Cut & Clean Combo
• 53816
Stainless Steel Sink
• 3587
Deluxe Classic
Drop-In Grill
• 31-S
Deluxe Gourmet
Drop-In Grill
• 3C-S
Regal I
Drop-In Grill
• 34-S
Drop-In
Single Side Burner
• 3280
Searing Station
+
• 32874-1 (shown)
• 3287L-1
• 3278-1
Single Side Burner
+
• 32794-1 (shown)
• 3279L-1
• 3279-1
Power Burner
+
• 19 Series
Double Searing Station
+
• 32884-1 (shown)
• 3288L-1
• 3288-1
Bar Caddy
• 1D-S0
Drop-In
Refreshment Center
• 33596
Slide-In
Refreshment Center
• 3596A
Beverage Center
• 1D-SSA
• 1D-SSD
33½
20
26
26
Pantry Style Sealed
Door/Drawer Combo
• 54018S
Large Pantry Style Sealed
Door/Drawer Combo
• 54020S
17½
25
Double Side Burner
+
• 32814 (shown)
• 3281L
• 3281
12
16¼
15¼
15
Paper Towel Holder
• 53812
9¼
8
12
‡
Dbl. Trash Cabinet (shown)
• 53820TSC
Black Diamond
Dbl. Trash Cabinet
• 53820HTSC
14½
21
19½
+
3” clearance required
(on both sides) to access
Master Switch when
using material that
extends out from island
surface. (applies to Side
Burners, Power Burners,
& Searing Stations)
3”
See
DETAIL 4
(at right)
See
DETAIL 3
(at right)
DIMENSIONS IN INCHES
∞
Proper operation requires a floor drain
within 5ft. of the ice maker.
CLASSIC CHARCOAL BUILT-IN GRILLS
Model # Description
Opening Required
Width Depth Height
3334 32” Lift-A-Fire Charcoal 32¼” 19¾” 12”
3339 24” Lift-A-Fire Charcoal 24¾” 17¾” 12”
3324 31” Firemaster 3324 31¼” 21¼” 12”
3329 24” Firemaster 3329 24¼” 19¼” 12”
DETAIL 4
Door/Drawer
Frame Outline
Door frame varies in width (1"-2" ALL AROUND) depending
on the size & configuration of the door & drawer.
Pedestal Grill Dimensions
• A430s-7EAP-P6
• A430s-8EAP-P6
• C430s-RT1P-P6
Accessory Hanger Outline
Accessory hanger varies in width
(2”-2½” ALL AROUND) depending
on the size & configuration of the
accessory.
COUNTER-TOP
TOP VIEW
DETAIL 3
5
FOR COUNTER-TOP OVERHANG
A notch must be cut into
the overhang to allow the
accessory face to sit flush
with the front wall. Also,
allow clearance for control
panel removal.
6⅛”
12¼”
2⅞”
4¼”
6⅜”
1⅜”
1½” Dia.
Countertop
Flange Overlap Dimensions / Legacy Doors
Single Doors
1¾”
(Around)
Double Doors
1¾”
1½”
1½”
1¾”
DROP-IN GRILLS, ACCESSORIES, DOORS & DRAWERS
49⅞”
20¼”
57⅛”
26”
25”
A430s - 37”
C430s - 36”
A430s - 26”
C430s - 25¼”
A430s - 56”
C430s - 51¼”
BUILT-IN KEGERATOR ONLY
Notes
1. There is a hanger on three sides of the grill (SEE DETAIL 3).
2. The control panel (face) of the accessories is wider than the
cutout width, this conceals the cutout space on the left & right
hand sides.
3. Clearance of 10” on each side, and 3” at the rear of the oven is
recommended for unrestricted operation of accessories. (18”
from combustible surroundings on each side and rear)
4. Insulating liners must be used and are available for combustible
surrounds. Double Side burner (3281), Single Side burner (3279-
1) and Drop-In Side burner (3280) do not require an insulating
liner (See page 6).
TOP VIEW
(D) Horizontal Single Access Doors*
Model # Series Cutout (h x w)
23912-S Legacy
12½” x 18½”
23914-S Legacy
14½” x 20½”
23917-S Legacy
17½” x 24½”
(E) Vertical Single Access Doors*
Model # Series Cutout (h x w)
23918-S Legacy
18½” x 12½”
23920-S Legacy
20½” x 14½”
23924-S Legacy
24½” x 17½”
*
Doors can be flipped for reversible hinges
(F) Double Access Doors
Model # Series Cutout (h x w)
23930-S Legacy
20½” x 30”
See Detail 4 on page 5 for Flange Overlap Dimensions
Access Doors
‡
An additional ½" clearance is
necessary on each side, directly
around the screw assembly.