User Manual for Powe Burner Diamond Series

ManualsBrandsFire Magic ManualsBarbecue19 Inch Built-In Side Burner with 3,000 - 60,000 BTU, Double Ring Cast Brass Burner and Back-Lit Control Knobs: Porcelain Cast Iron Grid, Liquid Propane

L-C2-333

REV 3 - 1601181405

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

INSTALLATION AND OPERATING

INSTRUCTIONS

Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION

DANGER

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open cover.

4. If odor continues, keep away from the

appliance, and immediately call your

gas supplier or ﬁ re department.

WARNING

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

2. A propane cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This

appliance must be installed in accordance with

local codes and ordinances, or, in the absence

of local codes, with either the latest National

Fuel Gas Code (ANSI Z223.1/NFPA 54), and

Natural Gas and Propane Storage and Handling

Installation Code (CSA-B149.1).

This appliance and its individual shutoff valves

must be disconnected from the gas supply piping

system when testing the system at pressures in

excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valves during any pressure

testing of the gas supply system at pressures

up to and including ½ psig (3.5 kPa).

All electrical outlets in the vicinity of the appliance

must be properly grounded in accordance with local

codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical supply cords and fuel supply

hoses away from any heated surface.

WARNING

Improper installation, adjustment, alteration,

service, or maintenance can cause injury or

property damage. Refer to this manual. For

assistance or additional information consult

a qualiﬁ ed professional service technician,

service agency, or the gas supplier.

09-41

Certiﬁ ed to: ANSI Z21.58b-2012

CSA 1.6b-2012

19-4B Series

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

POWER BURNER

diamond series

WARNINGS AND SAFETY CODES

Summary of content (28 pages)

PAGE 1
POWER BURNER diamond series 19-4B Series INSTALLATION AND OPERATING INSTRUCTIONS INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference. Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION WARNINGS AND SAFETY CODES WARNING DANGER IF YOU SMELL GAS: 1. 2. 3. 4. 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2.
PAGE 2
SÛRETÉ ET CODES D’AVERTISSEMENT INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE DANS LE CONTRE- POWER BURNER DANGER: AVERTISSEMENT: SI VOUS SENTEZ LE GAZ : 1. Coupez l’admission de gaz de I’appariel. 2. Éteindre toute flamme nue. 3. Ouvrir le couvercle. 4. Si l’odeur persiste, éloignez-vous de l’appareil et appelez immédiatement le fournisseur de gaz ou le service d’incendie. 1.
PAGE 3
GETTING STARTED CONTENTS INSTALLATION GETTING STARTED INSTALLATION ........................................................ 15 ELECTRICAL SAFETY ...............................................3 POWER BURNER PARTS LIST ...................................4 MODEL SPECIFICATIONS ..........................................5 Model Specifications Table ........................................5 COUNTERTOP OVERHANG .....................................5 RECOMMENDED OFFSET INSTALL .........................
PAGE 4
POWER BURNER PARTS LIST Item Description Part No. Qty. 1. 2. or 3. 4. 5. 6. Power burner cover Natural gas orifice (left) ‡ 3001-30-1 1 or Propane gas orifice (left) ‡ 3001-50-1 1 7. Natural gas orifice (right) ‡ 3001-46-1 1 or Propane gas orifice (right) ‡ 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.
PAGE 5
MODEL SPECIFICATIONS MODEL SPECIFICATIONS TABLE Table 1 Inner burner N/P (right) orifice drill size #46 / #1.
PAGE 6
MODEL SPECIFICATIONS (cont.) RECOMMENDED OFFSET INSTALL It is highly recommended to build the enclosure for the power burner 6"-12" LOWER than your countertop (see Fig. 6-1). This will ensure a safer environment when using tall cooking pots like a turkey fryer, which can hold 40 lbs of hot oil. Consult Table 1 for power burner cut out dimensions. See Fig. 6-1 below for countertop offset installation information.
PAGE 7
MODEL SPECIFICATIONS (cont.) POWER BURNER DIMENSIONS TABLE Height (Top to bottom) Top of hanger to bottom of unit (E) Width (Left to right) Control panel Hanger to hanger width (F) (G) 22 3/4" 12" Depth (Front to back) Maximum depth (H) 19 3/4" F 24 3/4" H E G Fig.
PAGE 8
MAINTENANCE AND SAFETY INFORMATON 1. The power burner and surrounding area MUST remain clear of flammable substances such as gasoline, yard debris, wood, etc. 2. The airflow through the vent space located below the control panel must remain unobstructed. 3. When using propane gas: a. The required ventilation openings in the enclosure must be clear of debris. See the PROPANE SAFETY INFORMATION section. b.
PAGE 9
INSTALLATION REQUIREMENTS Installation must be performed by a qualified professional service technician. This unit is designed for outdoor use only. DO NOT use this unit inside a building, garage, enclosed area, or under overhead combustible construction. See below and the EXHAUST REMOVAL section on the following page for details on installing under non-combustible overhead construction. DO NOT use this unit in or on a recreational vehicle or boat.
PAGE 10
INSTALLATION REQUIREMENTS (cont.) The control panel MUST remain removable for servicing (see PARTS LIST). EXHAUST REMOVAL If the unit is installed under an overhead structure, it must be constructed of non-combustible material. An exhaust hood is recommended. See below. When using an exhaust hood: The cooking grid area must be covered by an exhaust hood (with a vent) larger than the cooking surface. Refer to manufacturer specifications.
PAGE 11
ENCLOSURE REQUIREMENTS VENTILATION (ALL ENCLOSURES) For All Piping Systems and All Gas Types: (Natural Gas, Household Propane, L.P. Cylinder) Ventilation Requirements: • Minimum 4 openings (2 per side wall - spaced at 180 degrees) FORYOUR SAFETY, you must provide the openings listed below for replacement air and cross-ventilation of the unit enclosure.
PAGE 12
PROPANE SAFETY INFORMATION WHEN OPERATING THIS APPLIANCE WITH PROPANE, ALL INSTRUCTIONS AND WARNINGS MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION CAUSING SERIOUS INJURY OR DEATH. WARNING This gas appliance, its enclosure, and the propane cylinder enclosure, if any, MUST be plumbed and vented in accordance with local building and safety codes and should be approved by local code enforcement officials. This appliance MUST be installed and operated according to the information below.
PAGE 13
SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS IMPORTANT FOR YOUR SAFETY READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER. When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed. FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION. CYLINDER/CONNECTOR REQUIREMENTS a. Propane-gas cylinders, valves, and hoses must be maintained in good condition and must be replaced if there is visible damage to either the cylinder or valve.
PAGE 14
UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE IMPORTANT POUR VOTRE SÛRETÉ LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE. En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements. LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.
PAGE 15
INSTALLATION INSTALLATION COUNTER PREPARATION INCORRECT Consult Table 1 for non-combustible enclosure cut-out dimensions. A RHP insulating liner must be used if any supporting construction is combustible. Consult the instructions that come with the liner for dimensions and additional installation information before beginning the installation.
PAGE 16
INSTALLATION (cont.) 4. Turn all burner control knobs to the OFF position. Turn the gas supply on. Then carefully check all gas connections for leaks with a brush and half-soap/half-water solution before lighting. NEVER USE A MATCH OR OPEN FLAME TO TEST FOR LEAKS. Receptacle Plug 5. Close the shut-off valve. CONNECT TO A POWER SOURCE CAUTION: Improperly connected wires will cause damage to the unit and may result in property damage and/or personal injury.
PAGE 17
INSTALLATION (cont.) To install using a power supply box (not included): 1. Install the power supply box at least 12 inches below the bottom of the power burner. Power burner 2. Fasten the power supply box to the inside of the enclosure. 3. Connect the power supply box connectors to the power burner wire harness extension, as shown in Fig. 17-1, A (molex and ground wire connections). 4. Connect the power burner wire harness extension to the power burner, as shown in Fig.
PAGE 18
INSTALLATION (cont.) POWER SUPPLY (MULTIPLE ACCESSORY UNITS) The previous section covers in detail how to individually connect this accessory unit to an Echelon grill power supply box. If multiple accessory units are to be installed, the following diagrams will assist in their installation.
PAGE 19
INSTALLATION (cont.) SLIDE UNIT INTO ENCLOSURE Slide the unit into place. Do not to pinch, kink, or damage the gas connector line. Note: Each side of the unit has a tab just behind the control panel. These tabs prevent the control panel from moving inward. If the tabs interfere with the unit sliding in (see Fig. 19-1), use pliers to bend them inward so that they clear the enclosure sides. Leave the tabs slightly out to ensure they still keep the control panel from moving inward (see Fig. 19-2). Fig.
PAGE 20
ALLUMAGE DES INSTRUCTIONS (D’ALLUMAGE) Lisez toutes les instructions avant l’allumage, et suivez ces instructions chaque fois vous lumière le unité. ÉCLAIRAGE ÉLECTRONIQUE Note: ÉCLAIRAGE MANUEL Le unité doitélectronique être relié à la puissance 120VAC pour L’éclairage exige une batterie installée l’éclairage électronique. de 9 volts avec une bonne charge.
PAGE 21
USE, CARE, & SERVICE LIGHTING (IGNITION) INSTRUCTIONS Read all instructions before lighting, and follow these instructions each time you light the unit. ELECTRONIC LIGHTING MANUAL LIGHTING Note: Electronic lighting requires an installedpower 9-volt This unit must be connected to 120VAC battery with alighting. good charge. for electronic 1. Open lid(s) or remove cover(s) from burner(s) to be lit. 2. Turn all gas control knob(s) to their OFF position(s). 3. Turn on the gas at its source.
PAGE 22
CARE & CLEANING APPLIANCE MUST BE COMPLETELY COOL WHEN CLEANING. DO NOT SPRAY ANY CLEANER OR LIQUIDS ON THE APPLIANCE WHEN HOT. The appliance must be cleaned as often as once a month (depending on use) to prevent grease build-up and other food deposits. INTERIOR THE BURNER PORTS MUST BE KEPT CLEAN TO ENSURE PROPER IGNITION AND OPERATION. Remove the burner (see orifice changing instructions) and clean the ports and slots as required. Also inspect and clean the burner inlet for insects and nests.
PAGE 23
CONVERT GAS TYPE / CHECK BURNER ORIFICES CAUTION: Make sure the unit is at a safe temperature and is isolated from gas and electrical supplies before beginning. A Gas regulator cap For your safety, exercise caution, and make sure you have adequate hand protection, such as gloves, when handling metal parts. CONVERT LABEL This unit comes from the factory configured for one type of gas as marked on the label behind the control panel.
PAGE 24
CONVERT GAS TYPE / CHECK BURNER ORIFICES (cont.) CONVERT/CHECK POWER BURNER ORIFICE 1. Remove the cooking grid. Grip the flame collimator and remove it by compressing the ring slightly front to back and lifting the compressed end upward. Reference the figure in the INSTALL THE FLAME COLLIMATOR section. 2. Check the orifice size by lifting the burner up and out of the locator hole and pulling it away from the orifices. The orifice size is stamped on the orifice face.
PAGE 25
AIR SHUTTER ADJUSTMENT Power burner air shutter(s) are located on the necks of the power burner as shown in Fig. 25-1. CAUTION: DO NOT handle a hot burner without adequate hand protection. To adjust the air shutters: Air shutters 1. Remove the cooking grid. Grip the flame collimator and remove it by compressing the ring slightly front to back and lifting the compressed end upward. Reference the figure in the INSTALL THE FLAME COLLIMATOR section. 2.
PAGE 26
CONTROL PANEL REMOVAL To remove the control panel: 1. Turn the control knobs to the OFF position and turn off the gas supply to the unit. 2. Remove the drip tray. 3. Turn off the light switch and disconnect the power supply from the power source. 4. Pull the control knobs from the stems and set aside. 5. Slowly lift away the lighted bezels to clear the valve stems, and carefully disconnect the wires found on the back of the bezels (use your fingernail). See Fig. 26-1. 6.
PAGE 27
TROUBLESHOOTING If you have trouble with this Fire Magic® unit, please use this list to identify the problem. By trying one or more of the solutions to the possible cause, you should be able to solve the problem. If this list does not cover your present problem, or if you have other technical difficulties with the unit, please contact your local Fire Magic® dealer or visit our web site at www.rhpeterson.com.
PAGE 28
WARRANTY PETERSON FIRE MAGIC GRILLS AND ACCESSORIES LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Fire Magic® grill to be free from defects in material and workmanship. Fire Magic® cast stainless-steel burners, stainless-steel rod cooking grids, and stainless-steel housings are warranted for as long as you own your Fire Magic® grill -- LIFETIME. (Except as noted below.) Fire Magic Choice stainless steel tubular burners are warranted for TWENTY (20) YEARS.