Installation and Operation

ManualsBrandsFire Magic ManualsBarbecueWall Mount Ventilation Hood with 1,200 CFM, 304 Series Stainless Steel Construction, Dual Halogen Lamps, Thermal Safety Sensor and Anodized Aluminum Filters: 48"

REV 2 - 1406051400

L-C2-387

Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

WALL VENT HOOD

For Outdoor Use Only

36-VH, 42-VH, 48-VH and 60-VH series

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

42-VH-6 model shown

WARNINGS AND SAFETY CODES

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the grill this vent hood

is installed above.

2. Extinguish any open ﬂ ame.

3. Open the lid of the grill.

4. If odor continues, keep away from the

appliances and immediately call your gas

supplier or the ﬁ re department.

WARNING:

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of the gas grill this vent hood is

installed above, or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of the

gas grill this vent hood is installed above,

or any other appliance.

All electrical outlets in the vicinity of the grill

and vent hood must be properly grounded in

accordance with local codes, or, in the absence

of local codes, with the National Electrical Code,

ANSI/NFPA 70, or the Canadian Electrical Code,

CSA C22.1, whichever is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury

or property damage. For proper installation,

refer to the installation instructions. For as-

sistance or additional information, consult

a qualiﬁ ed professional installer or service

agency.

Certiﬁ ed to: ANSI Z21.58b-2012

CSA 1.6b-2012

10-33

WARNING:

To avoid the risk of property damage and/or

personal injury, installation work and electrical

wiring must be performed by a qualiﬁ ed

professional installer. This appliance must be

installed in accordance with this instruction.

CAUTION:

• This vent hood is for outdoor, wall

mount installation only.

• For General Ventilating Use Only. Do Not

Use To Exhaust Hazardous Or Explosive

Materials And Vapors!

• Observe all local codes and ordinances

when installing this appliance. If no

local codes are applicable, wire unit

in accordance with the latest National

Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1,

whichever is applicable.

This vent hood is for outdoor,

wall mount installation only.

Summary of content (26 pages)

PAGE 1
WALL VENT HOOD For Outdoor Use Only 36-VH, 42-VH, 48-VH and 60-VH series 42-VH-6 model shown INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference. This vent hood is for outdoor, wall mount installation only. Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE. WARNINGS AND SAFETY CODES CAUTION: • This vent hood is for outdoor, wall mount installation only. • For General Ventilating Use Only.
PAGE 2
INSTRUCTIONS D'INSTALLATION ET MANUEL DU PROPRIÉTAIRE CAPOT DE PASSAGE DE MUR Pour l'usage extérieur seulement 36-VH, 42-VH, 48-VH, and 60-VH série INSTALLATEUR: Laissez ces instructions avec le consommateur. CONSOMMATEUR: Maintenez pour la future référence. Ce capot de passage est pour extérieur, installation de bâti de mur seulement. IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L'INSTALLATION OU L'UTILISATION AVERTISSEMENTS ET CODES DE SÛRETÉ ATTENTION: AVERTISSEMENT: 1.
PAGE 3
CONTENTS GETTING STARTED IMPORTANT PRE-INSTALLATION AND SAFETY INFORMATION ............................................ 5 REPLACEMENT PARTS LIST ................................................................................................................. 6 SPECIFICATIONS AND DIMENSIONS ................................................................................................ 7 TOOLS REQUIRED ...........................................................................................................
PAGE 4
L'INFORMATION IMPORTANTE DE PRÉINSTALLATION ET DE SÛRETÉ AVERTISSEMENT! 1. Lisez toutes les instructions. 2. CE CAPOT DE PASSAGE EST POUR EXTÉRIEUR, INSTALLATION DE BÂTI DE MUR SEULEMENT. Extérieur est défini comme secteur qui a l'air illimité, s'ouvrent aux éléments à tout moment. Un mur est défini comme côté d'un plancher et d'un toit se reliants de bâtiment. 3. L'installation, le service, et la réparation doivent être faits par un technicien qualifié de service professionnel. 4.
PAGE 5
IMPORTANT PRE-INSTALLATION AND SAFETY INFORMATION WARNING! 1. Read all instructions. 2. THIS VENT HOOD IS FOR OUTDOOR,WALL MOUNT INSTALLATION ONLY. Outdoor is defined as an area that has unconfined air, open to the elements at all times. A wall is defined as a side of a building connecting floor and roof. 3. Installation, service, and repair must be done by a qualified professional service technician. 4. This vent hood is for use with a gas grill only.
PAGE 6
REPLACEMENT PARTS LIST 36-VH-6 Item Description 42-VH-6 48-VH-6 60-VH-6 Part No. Qty. Part No. Qty. Part No. Qty. Part No. Qty. VH-11 1 VH-11 1 VH-11 1 VH-11 1 VH-17-6 1 VH-19-6 1 VH-22-6 1 VH-21-6 1 VH-36-01-6 1 VH-42-01-6 1 VH-48-01-6 1 VH-60-01-6 1 VH-12-6 2 VH-12-6 2 VH-12-6 2 VH-12-6 2 1. Transition 2. Wall mount bracket 3. Complete vent hood assembly 4. Light assembly* 5.
PAGE 7
SPECIFICATIONS AND DIMENSIONS 36-VH series 42-VH series 48-VH series Specification Value Value Value Unit height * 18" 18" 18" Unit width 36" 42" 48" Unit depth 30" 30" 30" * Height is of vent hood only (not accounting for transition). Specification Transition height 36-VH series Value 10" 42-VH series Value 10" 48-VH series Value 10" 60-VH series Value 18" 60" 30" 60-VH series Value 10" Specification Electrical requirements Value 120 volts, 60 hertz, 20 amp; GFI outlet.
PAGE 8
SPECIFICATIONS AND DIMENSIONS (cont.) WIRING DIAGRAM Wire harness, blower vent hood Power cord Wire harness, main vent hood Thermostat Snap Disc Assy Blower Motor 600 CFM 3-position rotary switch Light Assy 120V 50 Watt Fan switch Light switch TOOLS REQUIRED The following are the minimum tools required for the installation of your vent hood components. Additional tools may be required for your individual installation.
PAGE 9
INSTALLATION REQUIREMENTS - FIRE MAGIC SPACER & DUCT COVER Fire Magic offers a spacer and duct cover specifically designed for your vent hood. Reference the information below for an overall orientation. (Contact your dealer for ordering information.) In order to use these prefabricated components, ensure the component dimensions allow for an appropriate install as addressed below (as individual setups may vary).
PAGE 10
INSTALLATION REQUIREMENTS - CUSTOM SPACER & SOFFIT When constructing a custom spacer and soffit, reference the information below for an overall orientation. • • • • THIS VENT HOOD IS FOR OUTDOOR, WALL MOUNT INSTALLATION ONLY. Installation must be done by a qualified professional service technician. Below is a diagram of a generic installation. Please review and understand this section prior to proceeding with installation. VENT PIPING Install 10" round galvanized (single wall) vent piping as required.
PAGE 11
INSTALLATION THIS VENT HOOD IS FOR OUTDOOR, WALL MOUNT INSTALLATION ONLY. To ensure safety and proper performance; the vent hood installation must be done by a qualified professional service technician. Reference the INSTALLATION REQUIREMENTS section during the course of the install for dimensions and overall orientation. Baffle If possible, the gas grill should be removed for ease of installation and to prevent damage to the grill. Fig.
PAGE 12
INSTALLATION (cont.) Custom Spacer: R O O F Construct the spacer frame according to your individual install preference, while following the guidelines found in the INSTALLATION REQUIREMENTS section. The front of the spacer (that is exposed to the rear of the vent hood); must include a solid wall to allow for the vent hood to be properly secured into it. R When designing the spacer; account for the thickness of your finishing substrate so that overall dimensions are flush with the vent hood.
PAGE 13
INSTALLATION (cont.) WALL MOUNT BRACKET The wall mount bracket must be installed into the spacer to assist in supporting the vent hood. Fire Magic Spacer To install wall mount bracket to Fire Magic Spacer: Fire Magic spacers are designed with pre-drilled holes and include screws for ease of bracket installation. 1. Center the bracket (from left-to-right) over the channel located on the front center of the Fire Magic Spacer. 2.
PAGE 14
INSTALLATION (cont.) VENT HOOD 1. Rest the vent hood onto the wall mount bracket, being sure that the tabs on the bracket engage the slots on the rear of the hood for proper support. See Fig. 14-1. 2. Ensure the sides, top, and bottom of the vent hood sit flush with the spacer (see Fig. 14-2). (The spacer will already be finished with any applicable substrate, to allow for the vent hood to rest flush.) 3.
PAGE 15
INSTALLATION (cont.) VENT PIPING Cap A cutout will need to be made in the roof to route the piping through; and must be sealed with silicone to prevent leaks. 1. Install 10" round galvanized rigid (single wall) vent piping from the transition on, as required. All joints must be sealed using duct tape. Install 10" round vent piping as needed (ROOF) Important: Vent piping should be installed as straight as possible to prevent back-pressure on the fans.
PAGE 16
INSTALLATION (cont.) FAN ASSEMBLY 1. Locate the (4) nuts pre-installed to the ceiling of the vent hood, and using a 3/8" nut driver, loosen (but do not remove) to allow for the fan assembly to be inserted. See Fig. 16-1. B A 2. With the open ends of the fans facing the front of the vent hood, carefully position the fan assembly, aligning the keyholes to the loosened nuts. See Fig. 16-1, A. 3.
PAGE 17
INSTALLATION (cont.) BAFFLE 1. Carefully raise the baffle up into the vent hood. You will first need to slide one side in at a slight angle, until the baffle edge aligns above the inner wall (see Fig. 17-1). Then raise the opposite side of the baffle until it also aligns. Drop the baffle into place. 2. Align the 4 screw holes (2 on each side), then secure the baffle in place using a medium Phillips screwdriver and the supplied 8-32 x 3/8" screws (that were originally removed at beginning of installation).
PAGE 18
INSTALLATION (cont.) ELECTRICAL This vent hood will require electrical work, and includes a power cord. The install will need a dedicated GFI receptacle installed near the vent hood to allow for the power cord to be plugged into. The area above the vent hood that the soffit / duct cover will enclose is an ideal location (reference Fig. 18-1). Install GFI receptacle, connect power cord (vent piping not shown for clarity) 1. Install GFI receptacle accordingly. Observe all codes. Fig.
PAGE 19
INSTALLATION (cont.) Custom Soffit: R O O F Construct the soffit frame according to your individual install preference, while following the guidelines found in the INSTALLATION REQUIREMENTS section. When designing the soffit; account for the thickness of your finishing substrate so that overall dimensions are flush with the vent hood and spacer below. The soffit must allow permanent interior access (i.e. access panel/door). R • Soffit must be properly secured into REAR WALL studs.
PAGE 20
OPÉRATION VENTILATEUR DE CAPOT DE PASSAGE Pour faire fonctionner les ventilateurs, il suffit de tourner le bouton du ventilateur situé à l'avant droit de la hotte au réglage désiré. Le bouton du ventilateur est symbolisé par un logo fan gravé à côté de lui. Voir la Fig. 20-1. VENTILATEUR LUMIÈRES Tournez le bouton à la position OFF pour allumer les ventilateurs éteints. Mettez toujours les fans avant de cuisson afin d'établir un flux d'air.
PAGE 21
OPERATION VENT HOOD FANS To operate the fans, simply turn the fan knob located on the front right of the vent hood to your desired setting. The fan knob is symbolized with a fan logo etched beside it. See Fig. 21-1. FANS LIGHTS Turn the knob to OFF position to turn the fans off. Always turn the fans on before cooking to establish an air flow. Allow the fans to operate for few minutes after you turn the grill off, to clear the air out and keep the area smoke free.
PAGE 22
SERVICING AND CLEANING The unit must be off and the power cord must be disconnected prior to beginning any service or cleaning. Any components removed during servicing/cleaning must be reinstalled, as previously instructed in this manual, prior to future operation. CONTACT YOUR DEALER FOR REPLACEMENT PARTS. Wipe with grain REMOVE FIRE MAGIC DUCT COVER (if applicable) If a Fire Magic Duct Cover is installed, it must first be removed in order to access and disconnect the power cord.
PAGE 23
SERVICING AND CLEANING (cont.) REPLACING HALOGEN BULBS Important: ONLY REPLACE WITH 120V / 50 WATT HALOGEN BULB(S). Important: Wear gloves during this procedure for safety and to maintain bulb life. 1. Ensure the power cord has been disconnected. 2. With one hand directly below the light assembly, gently pry the glass lens out using a thin flat-head screwdriver. Slowly twist the screwdriver handle until the lens is removed. Note: Replacement should only be done on a light assembly that is completely cool.
PAGE 24
NOTES PAGE Please use this page to record any information that you may want to have at hand.
PAGE 25
TROUBLESHOOTING If you have trouble with this vent hood, please use this list to identify the problem. By trying one or more of the solutions to the possible cause, you should be able to solve the problem. If this list does not cover your present problem, or if you have other technical difficulties with the vent hood, please contact your local Fire Magic dealer or visit our web site at www.rhpeterson.com.
PAGE 26
WARRANTY PETERSON FIRE MAGIC GRILLS AND ACCESSORIES LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Fire Magic® grill to be free from defects in material and workmanship. Fire Magic® cast stainless-steel burners, stainless-steel rod cooking grids, and stainless-steel housings are warranted for as long as you own your Fire Magic® grill -- LIFETIME. (Except as noted below.) Fire Magic Choice stainless steel tubular burners are warranted for TWENTY (20) YEARS.