Use & Care Guide

ManualsBrandsFire Magic ManualsBarbecue36 Inch Built-In Grill with 540 Sq. In. Grilling Area, 77,000 BTU, Cast Stainless Steel "E" Burners, Infrared Burner, Rotisserie, Meat Probe, Digital Thermometer, Removable Warming Rack, Interior Lighting and Advanced Hot Surface Ignition: Liquid Prop

Note: When a propane cylinder is installed inside

of the enclosure, the guidelines found in the

ENCLOSURE REQUIREMENTS section

MUST be followed.

For household propane or natural gas units:

CAUTION: Use only C.S.A. listed stainless-steel ﬂ ex

connectors within the enclosure.

WARNING

A rubber or plastic connector will rupture or leak,

resulting in an explosion or serious injury if used

inside the appliance enclosure.

a. Run the attached ﬂ ex connector routed under the

left side of the grill out of the enclosure and to the

gas stub.

b. Turn OFF the gas supply at the source. Then

connect the

" pipe adapter ﬁ tting supplied with

the stainless-steel ﬂ ex connector to the gas-supply

stub. Use pipe joint compound that is resistant to all

gasses on the male pipe ﬁ tting and tighten securely.

DO NOT use pipe joint compound to connect

ﬂ are ﬁ ttings.

d. Turn all burner control knobs to the OFF position.

Turn the gas supply on. Then carefully check all gas

connections for leaks with a brush and half-soap/

half-water solution before lighting. NEVER USE A

MATCH OR OPEN FLAME TO TEST FOR LEAKS.

e. Close the dedicated gas-supply shut-off valve, then

slide the grill into place. Do not to pinch, kink, or

damage the gas connector line.

f. Rotate the adjustable support screws to the left to

raise and to the right to lower the respective side

of the appliance grill. Use a

" open-end wrench

as needed.

Important: Do not extend the support screws so

far that any part of the hanger is raised

off the counter top.

COUNTER PREPARATION

Consult Table 1 for non-combustible enclosure cut-out

dimensions. A Robert H. Peterson insulating liner must

be used if the counter or any supporting construction is

combustible. Consult the instructions that come with the

liner for dimensions and additional installation information

before beginning the installation.

This outdoor built-in grill must be supported by the

stainless-steel hanger extending from the upper portion

of the grill. The hanger rests on the left, right, and back

of the countertop and on the two front structural supports

with attached adjustable screws located below the control

panel on the left and right sides (see Fig. 12-3).

The control panel is designed to sit ﬂ ush against the

enclosure front wall (see Fig. 12-2). If the non-combustible

enclosure countertop extends beyond the front wall,

creating a countertop overhang (see Fig. 12-1), it must

be cut ﬂ ush with the front wall for the width of the control

panel or a gap will be created exposing the forward

portions of the left and right side grill ﬁ re walls. Reference

the MODEL SPECIFICATIONS section.

Note: It is not necessary to remove the control panel

or knobs to install this unit.

CONNECTING THE GAS SUPPLY

For propane cylinders:

For connecting a propane unit to a portable propane tank,

read the safety warnings and follow the instructions in the

section SAFE USE AND MAINTENANCE OF PROPANE

GAS CYLINDERS.

INSTALLING THE BUILT-IN UNIT

Fig. 12-4

Fig. 12-1

Fig. 12-2

GAP CREATED

IDEAL

Flush-mounted

control panel

Proposed cut-

out in overhang

Countertop Countertop

Overhang

control panel

stops here

REV 8 - 1405291355

L-C2-276

OFF

Dedicated manual shut-off valve

To gas

system

Cut-out

Countertop

Hanger

Flex

connector

Gas inlet pipe

Fig. 12-3

Adjustable

support

screw

Bottom

of control

panel

Bottom

of cut-out

opening