User Manual

ManualsBrandsFire Magic ManualsGrillsAurora Series 30 Inch Freestanding Natural Gas Grill with Standard Burners, 660 sq. inches Grilling Surface Size, in Stainless Steel

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

STAND-ALONE OUTDOOR

GAS GRILLS

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁ re department.

WARNING:

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This grill

must be installed in accordance with local codes

and ordinances, or, in the absence of local codes,

with either the latest National Fuel Gas Code

(ANSI Z223.1/NFPA 54), and Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-supply

piping system when testing the system at pressures

in excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-supply

piping system by closing its dedicated manual

shutoff valve during any pressure testing of the gas-

supply system at pressures up to and including ½

psig (3.5 kPa).

All electrical outlets in the vicinity of the grill must

be properly grounded in accordance with local

codes, or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury

or property damage. For proper installation,

refer to the installation instructions. For

assistance or additional information,

consult a qualiﬁ ed professional installer,

service agency, or the gas supplier.

INSTALLATION

INSTRUCTIONS AND

OWNER’S MANUAL

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

SAFETY AND WARNING CODES

Proper operation of your grill

requires prompt and periodic

maintenance. See the CARE &

CLEANING section for details.

Certiﬁ ed to: ANSI Z21.58b-2012

CSA 1.6b-2012

11-093

REV 0 - 1412011415

L-C2-435

A430s, A530s, A540s, & A660s

A540s shown

Summary of content (36 pages)

PAGE 1
STAND-ALONE OUTDOOR GAS GRILLS A430s, A530s, A540s, & A660s INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference. A540s shown IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE. SAFETY AND WARNING CODES DANGER: IF YOU SMELL GAS: 1. 2. 3. 4. WARNING: 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2.
PAGE 2
INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE GRIL EXTÉRIEUR DE GAZ DU PORTATIF IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION SÛRETÉ ET CODES D’AVERTISSEMENT DANGER: AVERTISSEMENT: SI VOUS SENTEZ LE GAZ : 1. Coupez le gaz à l’appareil. 2. Éteignez-vous n’importe quelle flamme nue. 3. Ouvrez le couvercle si équipé d’un four. 4.
PAGE 3
CONTENTS 3 4 7 7 7 8 8 9 10 11 11 12 12 12 12 13 15 16 17 17 19 22 23 23 24 25 26 27 28 29 30 32 34 35 36 ELECTRICAL SAFETY REPLACEMENT PARTS LIST ELECTRICAL CONNECTIONS GRILL MAINTENANCE AND SAFETY INFORMATION LIGHT SWITCH STAND-ALONE GRILL DIMENSIONS TABLE MODEL SPECIFICATIONS TABLE STAND-ALONE GRILL WIRING DIAGRAM INSTALLATION REQUIREMENTS ENSURE PROPER COMBUSTION AIR AND COOLING AIRFLOW EXHAUST REMOVAL LOCATION PREPARATION WHEELS AND CASTERS INSTALLATION CONNECT THE GAS SUPPLY SAFE USE & MAINTENANCE OF
PAGE 4
REPLACEMENT PARTS LIST 1 2 6 4 5 10 3 36 39 8 9 37 7 19 21 24 28 34 32 18 23 26 49 20 22 25 15 30 33 17 27 16 14 53 13 35 To order replacement par ts, contact your local Fire Magic® dealer.
PAGE 5
REPLACEMENT PARTS LIST (cont.) A430s Item Description Part No. A530s Qty. Part No. A540s A660s Qty. Part No. Qty. Part No. Qty.
PAGE 6
REPLACEMENT PARTS LIST (cont.) A430s Item Description 28. Folding shelf 29. Part No. A530s Qty. Part No. A540s A660s Qty. Part No. Qty. Part No. Qty. 24316-15R/L 1 24326-15R/L 1 24316-15R/L 1 24326-15R/L 1 Sideburner shelf (only)* ‡ 24316-16 1 24326-16 1 24316-16 1 24326-16 1 30. Paper towel holder assembly 25387-11 1 25387-11 1 25387-11 1 25387-11 1 31. Tool holder assembly‡ 25387-12 1 25387-12 1 25387-12 1 25387-12 1 32.
PAGE 7
GRILL MAINTENANCE AND SAFETY INFORMATION 1. The outdoor grill and surrounding area MUST remain clear of flammable substances such as gasoline, yard debris, wood, etc. insects and insect nests. A clogged tube can lead to a fire beneath the grill. A proper flame pattern will ensure safe operation and optimal performance. Adjust the air shutter as needed (see AIR SHUTTER ADJUSTMENT). 2. The airflow through the vent space located below the control panel must remain unobstructed. 5.
PAGE 8
MODEL SPECIFICATIONS TABLE STAND-ALONE GRILL DIMENSIONS TABLE Height Width Left to right Floor to top (with oven) Model Open (A) Floor to top of shelf Cart base Closed (C) (D) (B) Depth Front to back (with shelves) Up (E) Down* (F) 1 Up / 1 Down (G) Cart base (H) Maximum outer (I) A430s 57 1/4" 50" 37" 26" 55 3/4" 35 1/4" 45 1/2" 21 3/4" 25 3/4" A530s 60 5/8" 52" 37" 26" 55 3/4" 35 1/4" 45 1/2" 26 29 3/4" A540s 57 1/4" 50" 37" 32 1/4" 1/2" 52" A660s 60 5/8" 52" 37
PAGE 9
MODEL SPECIFICATIONS (cont.) STAND-ALONE GRILL DIMENSIONS TABLE Table 1 A430s A530s A540s Main burner quantity 2 2 3 N/P orifice drill size #42 / #54 #40 / #53 #44 / #55 Backburner * #52 / #59 #52 / #59 #48 / #56 N/P orifice drill size Sideburner * #50 / #58 #50 / #58 #50 / #58 N/P orifice drill size Infrared searing burner * #49 / #56 #45 / #55 #49 / #56 N/P orifice drill size Power supply rating 120VAC / 0.
PAGE 10
INSTALLATION REQUIREMENTS Installation must be performed by a qualified professional service technician. Combustible This grill is designed for outdoor use only. DO NOT use this grill inside a building, garage, enclosed area, or under any overhead construction. DO NOT use this grill in or on a recreational vehicle or boat. Min. 18" Important: The grill is not insulated. Refer to the information below to ensure all required clearances are met.
PAGE 11
INSTALLATION REQUIREMENTS (cont.) The control panel MUST remain removable for servicing and air shutter adjustment (see PARTS LIST). INCORRECT Rear oven lid vent THIS UNIT MUST NOT BE LOCATED IN A FULLY ENCLOSED AREA OF ANY KIND. ENSURE PROPER COMBUSTION AIR AND COOLING AIRFLOW Proper airflow (Fig. 11-1) MUST be maintained for the grill to perform as it was designed. If airflow is blocked, overheating and poor combustion will result. Do not block the 1" (2.
PAGE 12
INSTALLATION LOCATION PREPARATION INSTALL THE TOOL HOLDER AND PAPERTOWEL HOLDER Prepare a flat, level surface capable of supporting the weight of the stand-alone grill and convenient to The rectangular mounting bracket for the tool the gas supply if connecting to a gas line. holder and the paper towel holder come preattached to the sides of the cart.
PAGE 13
SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS IMPORTANT FOR YOUR SAFETY READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER. When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed. FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION. CYLINDER/CONNECTOR REQUIREMENTS a. Propane-gas cylinders, valves, and hoses must be maintained in good condition and must be replaced if there is visible damage to either the cylinder or valve.
PAGE 14
UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE IMPORTANT POUR VOTRE SÛRETÉ LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE. En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements. LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.
PAGE 15
INSTALL THE SIDEBURNER SHELF (IF EQUIPPED) This shelf comes separate from the grill for convenience in shipping. The sideburner shelf must be installed using the following instructions before hooking up the grill to a gas source. Screw Air shutter Hole Brass Shelf INSTALL THE SIDEBURNER SHELF 1. Remove the protective plastic from the grill, sideburner, and sideburner lids by carefully peeling it off with your fingers. Do not use tools. orifice Fig. 15-1 Air-shutter orifice placement - under shelf 2.
PAGE 16
IDENTIFICATION OF GRILL CONTROLS A430s and A530s controls Right main burner control knob Control panel screw(s) Sideburner control knob (if equipped) Backburner control knob (if equipped) Left main burner control knob Digital thermometer Drip tray Fig.
PAGE 17
LIGHTING (IGNITION) INSTRUCTIONS Read all instructions before lighting, and follow these instructions each time you light the unit. ELECTRONIC LIGHTING MANUAL LIGHTING This unit must be connected to 120VAC Note: Electronic lighting requires an installedpower 9-volt for electronic battery with alighting. good charge. 1. Open lid(s) or remove cover(s) from burner(s) to be lit. CAUTION: Always wait five (5) minutes for gas to clear after any unsuccessful lighting attempt. 2.
PAGE 18
ALLUMAGE DES INSTRUCTIONS (D’ALLUMAGE) Lisez toutes les instructions avant l’allumage, et suivez ces instructions chaque fois vous lumière le unité. ÉCLAIRAGE ÉLECTRONIQUE Note: ÉCLAIRAGE MANUEL Le unité doitélectronique être relié à la puissance 120VAC pour L’éclairage exige une batterie installée l’éclairage électronique. de 9 volts avec une bonne charge. RRN O SUTU TO ATTENTION: Attendez toujours cinq (5) minutes le gaz pour se dégager après que n’importe quelle 1.
PAGE 19
DIGITAL THERMOMETER Your grill comes with a digital thermometer for oven and meat probe temperature monitoring, and timed cooking. Pressing the power button will turn on the thermometer. The thermometer will automatically shut off after 5 minutes if no temperature change is detected. Meat probe handle The thermometer is located on the control panel between the control knobs. Plug in the meat probe on the right side of the control panel as shown in Fig. 19-1. FOR BEST PERFORMANCE, GENTLY PRESS THE BUTTONS.
PAGE 20
DIGITAL THERMOMETER (cont.) Set time as desired Setting the Timer 1. Press the timer button. Use the arrows to set the desired amount of time (see Fig. 20-1.) TIMER 05:00 2. Press SET to return to the default screen. The time remaining will be shown on the default screen. Once the time reaches zero; the display will flash red and the alarm will sound. The alarm is silenced by pressing any button on the thermometer. Use arrows to set ® SET MENU Timer button MENU SCREEN Fig.
PAGE 21
DIGITAL THERMOMETER (cont.) Setting the Alarm The alarm can be individually set (ON or OFF) for the meat probe and oven temp. The default setting has the alarm OFF for the meat probe and oven temp. The alarm always alerts for the TIMER. OVEN PROBE OFF ON ® 1. Under the menu screen select ALARM. Press SET. 2. Use the up/down arrow to select the desired alarm, and press the power button to turn the alarm ON/OFF. 3. Press SET to return to the menu screen.
PAGE 22
OPTIONAL ROTISSERIE Backburner cover Rotisserie rod bracket Warming rack Rotisserie rod rear bracket A B Rotisserie motor bracket 1 Rotisserie rod and knob FIR EM AG IC Meat holders Fig. 22-1 Counterbalance Rotisserie motor Rotisserie motor Heavy-duty Rotisserie motor 2 Rod drive socket Rod drive socket 1 Rocker switch Rotisserie motor slots (4) Rotisserie motor bracket Fig. 22-3 Fig. 22-2 Fig.
PAGE 23
USING THE FOLDING SHELF DROP-SHELF OPERATION A. To lower the shelf, grasp the middle of the shelf on both sides and lift upward so that the inner lip of the shelf, along the side of the grill, lifts out of the locking slot. Then use the handle to allow the end of the shelf to slowly rotate down as pictured to the right. CAUTION: Do NOT place fingers near hinge when closing. Being lowered or raised B. To raise the shelf, perform the opposite of A. above.
PAGE 24
OPTIONAL INFRARED BURNER OPERATION The infrared (IR) searing burner (optional) cooks with WARNING a powerful radiant heat. Only handle the infrared burner cover when the unit is cold or with a well-insulated long-handled tool or heat resistant gloves. Cover SIDE VIEW (with cover on) Cut-out for Flash tube Flash tube Ignitor electrode NO foreign objects Drippings and other Airborne liquids dust or grease Ignitor electrode Fig. 24-1 Cover Flash tube Food particles or debris OFF HI LIGHT Fig.
PAGE 25
GRILLING TIPS The art of grilling involves learning the nuances of your WIND CONSIDERATIONS grill and knowing how various cuts of meat and other Wind direction can have an effect on the grill, foods cook on it under different settings and conditions. especially with the oven open. For maximum stability Each grill will be unique due to its configuration and convenience, position the grill so that the oven and how it is positioned or installed. This section opens toward any prevailing wind (Fig. 25-1).
PAGE 26
ACCESSORIES GRILL BRUSH (optional) WARMING RACK (if equipped) Purchase a Fire Magic® stainless-steel grill brush (sold separately) to keep your grill cleaner. It comes with scraper for large particles and a replaceable head with brass bristles for overall cleaning. The warming rack (Fig. 26-2) is packed separately. To install the warming rack, lift the front of the rack up slightly and insert the rack hangers into the two holes in the back of the inner oven hood.
PAGE 27
FIRE MAGIC® DRIP TRAY Drippings from grilling flow through specially designed channels and collect in the drip tray. Check the drip tray regularly and empty when required. Fig. 27-1 Fig. 27-2 Pull out the drip tray and place liner Your grill includes a pack of four (4) Fire Magic® drip tray liners (Fig. 27-1). For your convenience in cleanup, place a liner into the drip tray before grilling. To fit a liner into the drip tray, pull out the tray and set it on a flat, level surface.
PAGE 28
CARE & CLEANING APPLIANCE MUST BE COMPLETELY COOL WHEN CLEANING. DO NOT SPRAY ANY CLEANER OR LIQUIDS ON THE APPLIANCE WHEN HOT. The appliance must be cleaned as often as once a month (depending on use) to prevent grease build-up and other food deposits. in Wipe with gra INTERIOR THE BURNER PORTS AND CARRY-OVER PORTS/ SLOTS MUST BE KEPT CLEAN TO ENSURE PROPER IGNITION AND OPERATION. Fig.
PAGE 29
REPLACING HALOGEN BULBS Your grill is engineered with the conveniences of electrical power for illuminating and igniting the grill. 5. Wearing a pair of gloves, reach into the fixture, gently grab the bulb, and pull it straight out of the fixture so that the two pins at the base of the bulb come all the way out. To replace any oven light, follow the instructions below. Important: ONLY REPLACE WITH 12V / 10 WATT HALOGEN BULB(S). WARNING Important: Bulb is halogen. DO NOT TOUCH with bare hands.
PAGE 30
CONVERTING THE GAS TYPE REGULATOR CONVERSION Required tools: • Phillips-head screwdriver (#2 medium) The gas regulator, located behind the control panel, must • Needle-nose pliers be set for the type of gas used to fuel the grill. To check • 3/8" hex nut driver (deep socket) the regulator setting, remove the cap in the center of the • 5/16" hex nut driver regulator (Fig. 30-1). Holding the cap vertical (see Fig.
PAGE 31
CONVERTING THE GAS TYPE 4. Remove the back panel by pulling the bottom toward the front of the grill and rotating it upward and outward until the two top tabs attached to back wall of the oven can be removed from the slots in the top of the plate. 5. R e m o ve t h e b a c k b u r n e r assembly retaining screw on Retaining the lower left of the backburner screw using a Phillips-head screwdriver and set it aside. 6. Pull wire from the ignitor 6. Pull the the backburner assembly electrode (Fig.
PAGE 32
BURNER AIR SHUTTER ADJUSTMENT AIR SHUTTER ADJUSTMENT Important: 1. Follow the safety precautions and steps for main burner removal Fig. 32-2 in the CHANGING Adjustment THE MAIN BURNER screw ORIFICES section Adj. slot (steps 1-4). Air shutters are preset at the factory based on the gas the grill is built to burn. However, altitude or other local conditions may require air shutter adjustment for proper combustion. 2.
PAGE 33
BURNER AIR SHUTTER ADJUSTMENT (Cont.) BACKBURNER (IF EQUIPPED) Too large an air shutter opening will allow too much air into the burner, which will cause the flames first to shorten and then to appear to lift up off the ports. For the bottom of the flames to move closer to the ports, close the air shutter more. The air shutter is set at the factory. However, altitude or other local conditions may require air shutter adjustment for proper combustion. Blue flames behind burner screen Fig.
PAGE 34
CONTROL PANEL REMOVAL To remove the control panel: 1. Turn the control knobs to the OFF position. 2. Remove the drip tray. 3. Pull the control knobs from the stems and set aside. 4. Using a Phillips screwdriver, unscrew and remove the control panel fastener screws and washers (located on the left and right front face of the control panel). Retain the screws for later re-installation. 5.
PAGE 35
TROUBLESHOOTING If you have trouble with the unit, please use this list to identify the problem. By trying one or more of the solutions to the possible cause, you should be able to solve the problem. If this list does not cover your present problem, or if you have other technical difficulties with the unit, please contact your local dealer. PROBLEM POSSIBLE CAUSE CORRECTION 1a. System reset: Disconnect (wait 10 minutes minimum) and reconnect power to grill. With lights OFF, test ignition. 1.
PAGE 36
WARRANTY PETERSON FIRE MAGIC GRILLS AND ACCESSORIES LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Fire Magic® grill to be free from defects in material and workmanship. Fire Magic® cast stainless-steel burners, stainless-steel rod cooking grids, and stainless-steel housings are warranted for as long as you own your Fire Magic® grill -- LIFETIME. (Except as noted below.) Fire Magic Choice stainless steel tubular burners are warranted for TWENTY (20) YEARS.