Use & Care Guide

ManualsBrandsFire Magic ManualsBarbecue GrillFire Magic Aurora Collection A430S5L1NP6

REV 8 - 1401220800

L-C2-294

IMPORTANT:

READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁ re department.

WARNING:

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This grill

must be installed in accordance with local codes

and ordinances, or, in the absence of local codes,

with either the latest National Fuel Gas Code

(ANSI Z223.1/NFPA 54), and Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-supply

piping system when testing the system at pressures

in excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-supply

piping system by closing its dedicated manual

shutoff valve during any pressure testing of the gas-

supply system at pressures up to and including ½

psig (3.5 kPa).

All electrical outlets in the vicinity of the grill must

be properly grounded in accordance with local

codes, or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

WARNING:

Improper installation, adjustment,

alteration, service, or maintenance can

cause injury or property damage. For

proper installation, refer to the installation

instructions. For assistance or additional

information, consult a qualiﬁ ed professional

installer, service agency, or the gas

supplier.

SAFETY AND WARNING CODES

430s Patio

mount shown

without

backburner

option

STAND-ALONE POST OUTDOOR

GAS GRILLS

INSTALLATION

INSTRUCTIONS AND

OWNER’S MANUAL

A430s (IN-GROUND AND PATIO MOUNT)

Proper operation of your grill requires

prompt and periodic maintenance.

See the CARE & CLEANING section

for details.

Certiﬁ ed to: ANSI Z21.58b-2012

CSA 1.6b-2012

11-093

Summary of content (36 pages)

PAGE 1
STAND-ALONE POST OUTDOOR GAS GRILLS A430s (IN-GROUND AND PATIO MOUNT) INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL 430s Patio mount shown without backburner option INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference. IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE. SAFETY AND WARNING CODES DANGER: IF YOU SMELL GAS: 1. 2. 3. 4. WARNING: 1.
PAGE 2
INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE GRIL EXTÉRIEUR DE GAZ IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION SÛRETÉ ET CODES D’AVERTISSEMENT DANGER: AVERTISSEMENT: SI VOUS SENTEZ LE GAZ : 1. Coupez le gaz à l’appareil. 2. Éteignez-vous n’importe quelle flamme nue. 3. Ouvrez le couvercle si équipé d’un four. 4. Si l’odeur continue, gardez loin de l’appareil et appelez immédiatement votre département de fournisseur ou de feu de gaz. 1.
PAGE 3
CONTENTS 3 4 5 6 6 7 8 8 8 9 10 10 10 11 13 17 18 19 19 19 21 24 26 27 28 29 30 31 32 34 36 ELECTRICAL SAFETY REPLACEMENT PARTS LIST PRODUCT DATA TABLE POST PATIO MOUNT GRILL DIMENSIONS TABLE MODEL SPECIFICATIONS IN-GROUND POST GRILL DIMENSIONS TABLE ELECTRICAL CONNECTIONS OPERATIONAL SAFETY INFORMATION LIGHT SWITCH INSTALLATION REQUIREMENTS ENSURING PROPER COMBUSTION AIR AND COOLING AIRFLOW EXHAUST REMOVAL GAS SUPPLY PLUMBING REQUIREMENTS PATIO MOUNT INSTALLATION IN-GROUND POST INSTALLATION SAFE USE & MAI
PAGE 4
REPLACEMENT PARTS LIST 1 IMPORTANT Remove all packing material and discarded prior to lighting. 15 2 6 7 3 12 14 8 13 11 10 39 To order replacement par ts, contact your local Fire Magic® dealer. 25 5 40 17 20 25 16 18 32 19 21 9 27 23 26 44 22 24 S o m e i t e m s s h ow n are optional, or are not available for certain models. Your model may vary, refer to parts table. Robert H. Peterson Co.
PAGE 5
REPLACEMENT PARTS LIST (cont.) A430s Item Description Part No. A430s Qty. Item Description Part No. Qty. 1. Stainless cooking grid (set of 2) 3542-S-2 1 23. Drip tray 3084 1 2. Flavor grid (set of 2) 3063-S-2 1 24. Drip tray liner (set of 4) 3557 1 3. Main burner 3042-50 2 25. Rigid shelf 24330-017 2 4. Infrared burner (optional)‡ 3051 1 26. 1 Oven lid 23729-53 1 Patio mount hardware kit (if applicable) 24330-25 5. 6. Warming rack* 3672S-M 1 27.
PAGE 6
MODEL SPECIFICATIONS POST PATIO MOUNT GRILL DIMENSIONS TABLE Height Floor to top (with oven) Open (A) Closed (B) 57" 50" Width Left to right Floor to top of shelf Post base (C) (D) 37" 26" Depth Front to back (with shelves) Up (E) Down (F) 55 3/4" 35 1/4" Post base 1 Up / 1 Down (H) (G) 45 1/2" 18 1/2" Maximum outer (I) 25 3/4" G F A C E I B D REV 8 - 1401220800 Fig.
PAGE 7
MODEL SPECIFICATIONS (cont.) IN-GROUND POST GRILL DIMENSIONS TABLE Height* Floor to top (with oven) Open (J) Closed (K) 57" 50” Floor to top of shelf (L) Floor to bottom of extension below ground (M) 37” 18” Width Left to right Depth Front to back (with shelves) Post (N) 5 1/2” Up (O) down (P) 1 Up /1 Down (Q) 55 3/4" 35 1/4" 45 1/2" Post (R) Maximum outer (S) 5 1/2” 25 3/4" *Note: Height dimensions are approximate from ground level once installed.
PAGE 8
OPERATIONAL SAFETY INFORMATION 1. The outdoor grill and surrounding area MUST remain clear of flammable substances such as gasoline, yard debris, wood, etc. 2. The airflow through the vent space located below the control panel must remain unobstructed. 3. When using propane gas: a. The required ventilation openings in the enclosure must be clear of debris. clean the orifice and burner/venturi tubes for insects and insect nests. A clogged tube can lead to a fire beneath the grill.
PAGE 9
INSTALLATION REQUIREMENTS This grill is designed for outdoor use only. DO NOT use this grill inside a building, garage, enclosed area, or under an unprotected overhead combustible construction. See the EXHAUST REMOVAL section on the following page for details on installing under a patio roof. DO NOT use this grill in or on a recreational vehicle or boat. Combustible Min. 18" Important: The grill is not insulated. Refer to the information below to ensure all required clearances are met.
PAGE 10
INSTALLATION REQUIREMENTS (cont.) The control panel MUST remain removable for servicing and air shutter adjustment (see PARTS LIST). INCORRECT Rear Re ar o oven ove ven n lilid d ve vent nt ENSURING PROPER COMBUSTION AIR AND COOLING AIRFLOW Proper airflow (Fig. 10-1) MUST be maintained for the grill to perform as it was designed. If airflow is blocked, overheating and poor combustion will result. Do not block the 1" (2.
PAGE 11
PATIO MOUNT INSTALLATION PREPARE FOR INSTALLATION Wire Connections Consult a qualified professional installer. Access plate The flex connector can be routed out the back of the post, under the post base, or inside the post. The power supply cord is to be routed out the back. To gain access to the inside of the post, unscrew and carefully open the access plate on the rear of the post using a medium Phillips-head screwdriver. Retain the screws.
PAGE 12
PATIO MOUNT INSTALLATION (cont.) CONNECT GAS SUPPLY Wire Connections For household propane or natural gas units: Route the flex connector to the gas stub. Turn OFF the gas supply at the source. Remove the adapter that is loosely connected to the flex connector. Attach the adapter to the gas-supply stub using a pipe compound resistant to all gasses. Tighten securely. Then attach the open end of the flex connector to the adapter. Tighten securely.
PAGE 13
IN-GROUND POST INSTALLATION PREPARE FOR INSTALLATION Consult a qualified professional installer / licensed contractor. Wire Connections Access plate The in-ground post is designed primarily for installation with a permanent underground gas supply. The power supply cord is to be routed out the back. To gain access to the inside of the post, unscrew and carefully open the access plate on the rear of the post using a medium Phillips-head screwdriver. Retain the screws.
PAGE 14
IN-GROUND POST INSTALLATION (cont.) ATTACH POST EXTENSION 1. Attach the extension to the bottom of the grill post so that the open portion is toward the back of the grill and the five holes in the extension line up with the five (5) weld-nuts in the post (see Fig. 14-1). 2. From outside the joined post and extension, insert one of the 1/4 X 20"-5/8 bolts (supplied) into each of the five (5) bolt holes and tighten each using a 7/16" socket driver or wrench (see Fig. 14-2).
PAGE 15
IN-GROUND POST INSTALLATION (cont.) CONNECT GAS SUPPLY In-ground method shown. Individual setup may vary. For household propane or natural gas units: Route the flex connector to the gas stub. Turn OFF the gas supply at the source. Remove the adapter that is loosely connected to the flex connector. Attach the adapter to the gas-supply stub using a pipe compound resistant to all gasses. Tighten securely. Then attach the open end of the flex connector to the adapter. Tighten securely.
PAGE 16
UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE IMPORTANT POUR VOTRE SÛRETÉ LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE. En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements. LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.
PAGE 17
SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS IMPORTANT FOR YOUR SAFETY READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER. When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed. FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION. CYLINDER/CONNECTOR REQUIREMENTS a. Propane-gas cylinders, valves, and hoses must be maintained in good condition and must be replaced if there is visible damage to either the cylinder or valve.
PAGE 18
IDENTIFICATION OF GRILL CONTROLS A430s controls Right main burner control knob Control panel screw(s) Left main burner control knob Digital thermometer Backburner control knob (if equipped) Meat probe Drip Tray Light switch Fig. 18-1 To remove the control panel: • Turn off the gas shutoff valve. • Pull off the control knobs. Unscrew and remove the control panel screws and washers. • Lift the control panel up and outward, allowing it to rest on the internal chain(s).
PAGE 19
LIGHTING (IGNITION) INSTRUCTIONS Read all instructions before lighting, and follow these instructions each time you light the unit. ELECTRONIC LIGHTING MANUAL LIGHTING Grill must be connected to 120VAC power for Note: Electronic lighting requires an installed 9-volt electronic lighting. battery with a good charge. 1. Open lid(s) or remove cover(s) from burner(s) to be lit. CAUTION: Always wait five (5) minutes for gas to clear after any unsuccessful lighting attempt. 2.
PAGE 20
ALLUMAGE DES INSTRUCTIONS (D’ALLUMAGE) Lisez toutes les instructions avant l’allumage, et suivez ces instructions chaque fois vous lumière le unité. ÉCLAIRAGE ÉLECTRONIQUE Note: ÉCLAIRAGE MANUEL Le unité doitélectronique être relié à la puissance 120VAC pour L’éclairage exige une batterie installée l’éclairage électronique. de 9 volts avec une bonne charge. RRN O SUTU TO ATTENTION: Attendez toujours cinq (5) minutes le gaz pour se dégager après que n’importe quelle 1.
PAGE 21
DIGITAL THERMOMETER Your grill comes with a digital thermometer for temperature control, oven and meat probe temperature monitoring, and timed cooking. Pressing the power button will turn on the thermometer. The thermometer will automatically shut off after 5 minutes if no temperature change is detected. Meat probe handle The thermometer is located on the control panel between the control knobs. Plug in the meat probe on the right side of the control panel as shown in Fig. 21-1.
PAGE 22
DIGITAL THERMOMETER (cont.) Set time as desired Setting the Timer 1. Press the timer button. Use the arrows to set the desired amount of time (see Fig. 22-1.) TIMER 05:00 2. Press SET to return to the default screen. The time remaining will be shown on the default screen. Once the time reaches zero; the display will flash red and the alarm will sound. The alarm is silenced by pressing any button on the thermometer. Use arrows to set ® SET MENU Timer button MENU SCREEN Fig.
PAGE 23
DIGITAL THERMOMETER (cont.) Setting the Alarm The alarm can be individually set (ON or OFF) for the meat probe and oven temp. The default setting has the alarm OFF for the meat probe and oven temp. The alarm always alerts for the TIMER. OVEN PROBE OFF ON ® 1. Under the menu screen select ALARM. Press SET. 2. Use the up/down arrow to select the desired alarm, and press the power button to turn the alarm ON/OFF. 3. Press SET to return to the menu screen.
PAGE 24
OPTIONAL ROTISSERIE Backburner cover Rotisserie rod bracket Warming rack Rotisserie rod rear bracket A B Rotisserie motor bracket 1 Rotisserie rod and knob FIR EM AG IC Meat holders Fig. 24-1 Counterbalance Rotisserie motor Rotisserie motor Heavy-duty Rotisserie motor 2 Rod drive socket Rod drive socket 1 Rocker switch Rotisserie motor slots (4) Rotisserie motor bracket Fig. 24-3 Fig. 24-2 Fig.
PAGE 25
OPTIONAL INFRARED BURNER OPERATION The infrared (IR) searing burner (optional) cooks with WARNING a powerful radiant heat. Only handle the infrared burner cover when the grill is cold or with a well-insulated long-handled tool or heat resistant gloves. Cover SIDE VIEW (with cover on) Cut-out for Flash tube Flash tube Ignitor electrode NO foreign objects Drippings and other Airborne liquids dust or grease Ignitor electrode Fig. 25-1 Cover Flash tube Food particles or debris OFF HI LIGHT Fig.
PAGE 26
GRILLING TIPS The art of grilling involves learning the nuances of your WIND CONSIDERATIONS grill and knowing how various cuts of meat and other Wind direction can have an effect on the grill, foods cook on it under different settings and conditions. especially with the oven open. For maximum stability Each grill will be unique due to its configuration and convenience, position the grill so that the oven and how it is positioned or installed. This section opens toward any prevailing wind (Fig. 26-1).
PAGE 27
ACCESSORIES THE GRILL BRUSH (OPTIONAL) THE WARMING RACK (if equipped) Purchase a Fire Magic® stainless-steel grill brush (sold separately) to keep your grill cleaner. It comes with scraper for large particles and a replaceable head with brass bristles for overall cleaning. The warming rack (Fig. 27-2) is packed separately. To install the warming rack, lift the front of the rack up slightly and insert the rack hangers into the two holes in the back of the inner oven hood just above the backburner.
PAGE 28
FIRE MAGIC® DRIP TRAY Drippings from grilling flow through specially designed channels and collect in the drip tray. Check the drip tray regularly and empty when required. Fig. 28-1 Fig. 28-2 Pull out the drip tray and place liner Your grill includes a pack of four (4) Fire Magic® drip tray liners (Fig. 28-1). For your convenience in cleanup, place a liner into the drip tray before grilling. To fit a liner into the drip tray, pull out the tray and set it on a flat, level surface.
PAGE 29
CARE & CLEANING APPLIANCE MUST BE COMPLETELY COOL WHEN CLEANING. DO NOT SPRAY ANY CLEANER OR LIQUIDS ON THE APPLIANCE WHEN HOT. The appliance must be cleaned as often as once a month (depending on use) to prevent grease build-up and other food deposits. in Wipe with gra INTERIOR THE BURNER PORTS AND CARRY-OVER PORTS/ SLOTS MUST BE KEPT CLEAN TO ENSURE PROPER IGNITION AND OPERATION. Fig.
PAGE 30
REPLACING HALOGEN BULBS Fire Magic ® grills are all engineered with the conveniences of electrical power for illuminating and igniting the grill. Note: You may wish to take this opportunity to clean the lens with a standard household window cleaner and then dry it completely. To replace any oven light, follow the instructions below. 5.
PAGE 31
TROUBLESHOOTING If you have trouble with this Fire Magic® grill, please use this list to identify the problem. By trying one or more of the solutions to the possible cause, you should be able to solve the problem. If this list does not cover your present problem, or if you have other technical difficulties with the grill, please contact your local Fire Magic® dealer or visit our web site at www.rhpeterson.com.
PAGE 32
CONVERTING THE GAS TYPE REGULATOR CONVERSION Required tools: • Phillips-head screwdriver (#2 medium) The gas regulator, located behind the control panel, must • Needle-nose pliers be set for the type of gas used to fuel the grill. To check • 3/8" hex nut driver (deep socket) the regulator setting, remove the cap in the center of the • 5/16" hex nut driver regulator (Fig. 32-1). Holding the cap vertical (see Fig.
PAGE 33
CONVERTING THE GAS TYPE 4. Remove the back panel by pulling the bottom toward the front of the grill and rotating it upward and outward until the two top tabs attached to back wall of the oven can be removed from the slots in the top of the plate. 5. R e m o ve t h e b a c k b u r n e r assembly retaining screw on the lower left of the backburner using a Phillips-head screwdriver and set it aside. 6. Pull wire from the ignitor 6. Pull the the backburner assembly electrode (Fig.
PAGE 34
BURNER AIR SHUTTER ADJUSTMENT AIR SHUTTER ADJUSTMENT Important: 1. Follow the safety precautions and steps for main burner removal Fig. 34-2 in the CHANGING Adjustment THE MAIN BURNER screw ORIFICES section Adj. slot (steps 1-4). Air shutters are preset at the factory based on the gas the grill is built to burn. However, altitude or other local conditions may require air shutter adjustment for proper combustion. 2.
PAGE 35
BURNER AIR SHUTTER ADJUSTMENT (Cont.) BACKBURNER (IF EQUIPPED) Too large an air shutter opening will allow too much air into the burner, which will cause the flames first to shorten and then to appear to lift up off the ports. For the bottom of the flames to move closer to the ports, close the air shutter more. The air shutter is set at the factory. However, altitude or other local conditions may require air shutter adjustment for proper combustion. Blue flames behind burner screen Fig.
PAGE 36
WARRANTY PETERSON FIRE MAGIC GRILLS AND ACCESSORIES LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Fire Magic® grill to be free from defects in material and workmanship. Fire Magic® cast stainless-steel burners, stainless-steel rod cooking grids, and stainless-steel housings are warranted for as long as you own your Fire Magic® grill -- LIFETIME. (Except as noted below.) Fire Magic Choice stainless steel tubular burners are warranted for TWENTY (20) YEARS.