Quick Setup Guide

ManualsBrandsFire Magic Manualsbarbecues & grillsE790S4L1P71W

REV 2 - 1110241416

L-C2-336

Fig. 3-2

CORRECT

PLACE GRILL SO PREVAILING WIND

BLOWS TOWARD FRONT OF GRILL

ECHELON

diamond series

Outdoor Stand Alone

Gas Grill

Quick Start Guide

INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference.

Robert H. Peterson Co.

CAUTION: For your safety read the installation instructions and owner’s manual provided with the grill.

This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI

Z223.1/NFPA 54), and Natural Gas and Propane Storage and Handling Installation Code (CSA-B149.1).

This appliance and its individual shutoff valves must be disconnected from the gas-supply piping system when testing the system at pressures in excess of ½ psig.

This appliance must be isolated from the gas-supply piping system by closing its dedicated manual shutoff valve during any pressure testing of the gas-supply

system at pressures up to and including ½ psig.

This grill is designed for outdoor use only. DO NOT use this grill under unprotected ﬂ ammable surfaces. DO NOT use this grill inside a building, garage,

enclosed area, or an unprotected covered area (see paragraph below). DO NOT use this grill in or on a recreational vehicle or boat.

If installed or used under a patio roof, the cooking grid area must be fully covered by an exhaust hood with a vent. An exhaust fan with a rating of 1,000 CFM (cubic feet

per minute) (472 liters per second) or more may be necessary to effectively remove smoke and other cooking by-products from the area under the hood. Fire Magic Vent

Hoods are available to meet this requirement. This outdoor grill must not be used under overhead unprotected combustible construction. THIS UNIT MUST NOT BE

LOCATED IN A FULLY ENCLOSED AREA OF ANY KIND.

2-Unpacking

Carefully unpack the grill, removing all packing material and protective ﬁ lm. Verify that all

parts have arrived undamaged by consulting the parts list in the owner’s manual. Remove

foam packed hardware from oven area. (See Fig. 2-1.)

Consult the parts list in the owner’s manual. If any parts are missing or damaged,

immediately contact the Fire Magic dealer before beginning installation.

Important: The 2 shipping screws must be removed prior to removing the unit from

the wooden pallet. The screw located on the bottom left side of the unit is

accessed by opening the door. The screw located on the bottom right side of

the unit is accessed by removing the lower drawer.

To remove the drawer; pull it completely out. Release the drawer from the

drawer slides by pressing the black lever down on the right side, and up on

the left side.

Fig. 2-1

1-Safety

Lift out foam packed hardware

Remove plastic

zip-ties

3-Installation

Location

Locate the grill on a ﬂ at level surface with 18” clearance from the oven back

and sides to any combustible material or construction.

CAUTION: Wind blowing into or across the rear oven lid vent (Fig.

3-1) can cause poor performance and/or dangerous

overheating. Orient the grill so that the prevailing wind

blows toward the front of the grill (Fig. 3-2).

CAUTION: To prevent dangerous overheating, the rear of the unit must have

a minimum clearance of 4” (10.2 cm) from any backsplash/wall.

YOU MUST PROTECT REAR OVEN

VENT FROM PREVAILING WIND

Rear oven lid vent

INCORRECT

Fig. 3-1

ReRearar o oveven n lilid d veventnt

Ventilation diagram

Fig. 3-5

To connect the regulator/

hose assembly to the

propane-gas cylinder valve

ﬁ tting: Press the hand nut

on the regulator over the

Acme thread ﬁ tting on the

cylinder valve. Turn the hand

nut clockwise to engage the

threads and tighten until

snug.

Fig. 3-4 Type I Acme thread quick coupler

Vent

QCC

Type 1

valve

Brass Acme

thread ﬁ tting

Liquid level

indicator

(optional)

Hand nut with

Acme thread

Regulator

Hose

Hand wheel

Pressure

relief

valve

Connect Gas supply

These quick start instructions assume a

propane cylinder conﬁ gured unit. See main

instructions for natural gas or household

propane conﬁ gured units.

Place approved propane 20lb cylinder in tank

tray and lock holder in position (Fig. 3-3).

Connect quick coupler hose and regulator

supplied with unit to propane cylinder (Fig.

3-4).

Set all burner control valves to OFF and

open gas source control valve.

Follow the lighting instructions on the

reverse side of this guide.

Proper grill airﬂ ow must be maintained as

shown in Fig. 3-5.

SET

Fig. 3-3

Quick

coupler

Propane

cylinder (tank)

Sideburner

shelf (if

equipped)

Tool holder

Paper towel

holder

Backburner

cover (if

equipped)

Tank tray latch

NOTE: THE CONTROL PANEL DOES NOT NEED TO BE REMOVED

FOR INSTALLATION. IF REMOVAL IS REQUIRED IT MUST

BE DONE WITH CAUTION BY A QUALIFIED PROFESSIONAL

SERVICE TECHNICIAN, TO PREVENT ANY POSSIBLE WIRE

DISCONNECTIONS.

Summary of content (2 pages)

PAGE 1
Robert H. Peterson Co. Outdoor Stand Alone Gas Grill Quick Start Guide ECHELON diamond series CAUTION: For your safety read the installation instructions and owner’s manual provided with the grill. 1-Safety INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference. This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI Z223.
PAGE 2
4-Grill Setup Note: For infrared burner equipped grills; see detailed instructions included in your owners manual. Parts Placement Checklist Place the following items according to their position and orientation in Fig. 4-1: Cooking Grid Flavor grids, cooking grids, heat zone dividers, backburner cover, warming rack, meat probe. Backburner cover Flavor Grid (not with IR) Leave pre-installed E-burners in place to maintain proper alignment.