OWNER’S MANUAL Tabletop Heater Safety First! Read and become familiar with this entire manual.
TABLE OF CONTENTS • Read These Safety Instructions………………………….. 1 • Contents Breakdown……………………………………… 2 • Screw Packing List………………………………………… 3 • Assembly Procedure………………………………………. 3 • Assembly……………………………………………………. 4 • Safety First………………………………………………….. 7 • Tabletop Heater Location…………………………………. 8 • Checking For Leaks………………………………………... 8 • Before Operating…….……………………………………... 8 • Operating…………………………………………………….
READ THESE SAFETY INSTRUCTIONS If you smell gas: • Shut off gas to the appliance. • Extinguish any open flame. • If odor continues, immediately call your gas supplier or your Fire Department. WARNING Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily injury, death, or property damage. ATTENTION Only to be used outdoors. Warning: Accessible parts may be very hot. Keep young children away. Turn off the gas supply at the gas container after use.
CONTENTS BREAKDOWN 2
Item. Qty. 3 Item No. 11 Burner 1 Reflector 1 12 3/16” bolt 4 3 6mm Washer 3 13 M5x10mm bolt 1 4 Emitter screen 1 14 Tank Housing 1 5 Guard 1 15 Igniter button 1 6 Door Plate 1 16 Control knob 1 7 Base 1 17 Handle 1 8 Cast Iron weight 1 18 Regulator 1 9 M6x15mm bolt 4 19 60mm pin 3 10 3/16” bolt 4 20 M6 flange nut 3 Item No. 1 Item Qty. M6 Castle nut 2 SCREW PACKAGING LIST Item Qty. M6 Castle Nut 3 Item Qty.
ASSEMBLY STEP 1 STEP 2 1-1. Remove all parts of the heater from the packaging. (NOTE: Plastic ring on tank housing should already be in place but if it is not, slide the plastic ring over the bottom of tank housing.) 2-1. Use 4 pcs M6x15mm bolts to fix the tank housing to the base and cast iron weight (Note: weight is preassembled to base). 2-2. Tighten the bolts as shown above. STEP 3 STEP 4 3-1. Put the burner on the tank housing then fix them with 4 pcs 3/16” bolts. 4-1.
STEP 6 STEP 5 5-1. Fix 3 pcs pins of 60mm length to the emitter screen with 3 pcs flange nuts then tighten them. 6-1. Put the emitter screen on the burner. 6-2. Use 4 pcs 3/16” bolts to connect the emitter screen to the burner. Tighten the bolts. STEP 7 STEP 8 7-1. Put the guard on the burner over the emitter screen. 7-2. Put the ends of the guards into the holes of the burner. 8-1. Put 3 pcs washers on each pin of the 60mm length.
STEP 9 STEP 10 10-1. Fasten the reflector with 3 pcs M6 castle nuts. 9-1. Put the reflector through the pins and on the washers. STEP 11 STEP 12 11-1. Turn off the control knob of the burner. 11-2. Fix the 1.02 lbs. gas tank (not included) to the regulator (rotate the gas tank clockwise toward the regulator until tightened). 12-1.
SAFETY FIRST Read and become familiar with this entire manual, especially the following precautions: Caution: This appliance is for outdoor use only (outside any enclosure). Always make sure there is fresh air ventilation. • Use only outdoors in a well ventilated space. Never use in a building, garage or any other enclosed area. • Always maintain at least 18” clearance (top) and 24” clearance (side) from combustible materials. • Always place heater on a hard and level surface.
TABLETOP HEATER LOCATION • • • • The tabletop heater is for outdoor use only. Always ensure that adequate fresh air ventilation is provided. Always maintain proper clearance to combustible materials, i.e. top 18” and sides 24” minimum. Tabletop heater must be located on a stable and strong surface. Never operate heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored. CHECKING FOR LEAKS Make 1-2 oz.
• • • • • • • Heater is on a hard and level surface. There are no signs of spider or insect nests. All burner passages are clear. All air circulation passages are clear. Children, pets, clothing, flammable materials and items that can be damaged from radiant heat are away from the heater. Children and adults in the area have been alerted to the high temperature hazards; especially burns and clothing fires.
Lighting 1. Make sure control knob is in the “Off” position. 2. Push in and rotate the gas control knob to “Pilot” position. Depress gas control know for 30 seconds to allow air to purge. Once gas reaches burner, depress igniter button while holding gas control knob in. 3. Once burner is lit, hold control knob in for at least 30 seconds and release. 4. If burner does not stay lit, turn control knob to “Off” position and wait 5 minutes and repeat 2 and 3. 5.
AFTER OPERATING Make sure: • • • Gas control is in OFF position. Unscrew gas canister from regulator and store gas canister AWAY from heater when heater is not in use. Store heater in an upright position in a secure location. MAINTENANCE • To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis. • Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION Pilot will not light Fuel canister empty Opening blocked Air in supply system Loose connections Replace fuel canister Clean opening Purge air from system Check all fittings Pilot will not stay on Debris around pilot Loose connections Gas leak Lack of fuel pressure Clean dirty area Tighten connections Check connections Canister near empty. Replace fuel canister. Burner will not light Pressure is low Canister near empty. Replace fuel canister.
Distributed By: Well Traveled Living 716 S 8th Street Amelia Island, FL 32034 Toll Free: 866‐WTL‐SUPP Web: www.wtliving.com Email: cservice@welltraveled.net 1 YEAR LIMITED WARRANTY – Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use. This warranty does NOT cover normal wear and weathering, assembly and/or maintenance OR use in a commercial application.
