PRO Series Outdoor Patio Heater Model # LIP-10A-TGG-LPG-BU Item # 61159/61436 ATTACH YOUR RECEIPT HERE Serial Number ___________ Purchase Date ______ Manufacturer: Changzhou Wellife Furnace Co., Ltd. Questions, problems, missing parts? Before returning to your retailer, call our customer service hotline at 1-866-985-7877, 9 a.m. – 6 p.m., EST, Monday – Friday or email at cservice@welltraveled.net.
PACKAGE CONTENTS ASSEMBLY ITEM 61159 (One piece reflector) PART DESCRIPTION QTY 1 packed in 1 carton 1 (packed in 1 inner ctn) A Reflector Panel B Head Assembly C Tank Housing D Gas Hose E Regulator F Post 1 G Post Supports 3 (packed in 1 inner ctn) H Base 1 I Wheels 2 (packed with Head Assembly) 1 1 (attached to Head Assembly) 1 (packed with Head Assembly) HARDWARE CONTENTS ASS 2
PACKAGE CONTENTS ASSEMBLY ITEM 61436 (5 piece reflector) PART DESCRIPTION QTY 4 pcs panel and 1 pc center cap (packed in 2 inner ctns) 1 (packed in 1 inner ctn) A Reflector Panel and Center Cap B Head Assembly C Tank Housing D Gas Hose E Regulator F Post 1 G Post Supports 3 (packed in 1 inner ctn) H Base 1 Wheels 2 (packed with Head Assembly) I 1 1 (attached to Head Assembly) 1 (packed with Head Assembly) HARDWARE CONTENTS ASSEMBL 3
SAFETY INFORMATION SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install this appliance. If you have any questions regarding the product, please call customer service 1-866-985-7877, 9 a.m. – 6 p.m., EST, Monday – Friday. This manual contains important information about the assembly, operation and maintenance of this patio heater. General safety information is presented in the first few pages and is also located throughout this manual.
SAFETY INFORMATION 5
ASSEMBLY PREPARATION Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package contents list and hardware contents as listed on pages 2 and 3 of this manual. If any part is missing or damaged, do not attempt to assemble this product. Contact customer service for replacement parts.
ASSEMBLY 3. Attach the Post (F) to the Post Supports (G). Once you have tightened the bolts holding the Post Supports (G) to the Base (H), align the holes in the Post (F) with the holes on the tops of the Post Supports (G) and insert a M6x35 (CC) bolt through a M6 (HH) washer and then through the hole in the Post Support. Affix another M6 (HH) washer onto the bottom of the M6x35 (CC) bolt and secure with a M6 (DD) nut. Repeat this in the 5 remaining holes (6 holes total—2 for each Post Support piece).
ASSEMBLY 5. Attach Head Assembly (B) to Post (F). Note: There is a small piece of protective foam located in the neck of the Head Assembly that MUST be removed prior to attaching Head Assembly to the Upper Post. Route Gas Hose (D) down into Post and align 4 small holes on Head Assembly with 4 Small holes in Post (F). [HINT: Control knob should be above decal on post.] Insert 4 M6x10 (EE) bolts through 4 M6 lock washers into holes and tighten. 5 Hardware Used: 4 x EE, Bolt M6x10 and Lock Washer M6 6-1.
ASSEMBLY 7. Connect the hose and regulator to the LP cylinder. The LP cylinder is sold separately. Use a standard 20 lb. propane cylinder only. Lift the Tank Housing (C) up and rest it on the top of the assembled Post Supports (G). Screw Regulator (E) onto Gas Hose (D). Do not cross thread. Hand tighten securely. Attach Regulator (E) to valve on LP cylinder and hand tighten securely. Place LP tank onto base of heater and lower the Tank 7 Housing.
OPERATING INSTRUCTIONS Leak Test 1. 2. 3. 4. 5. Make 2-3 oz. of leak test solution (one part liquid dishwashing detergent and three parts water). Apply several drops of solution where hose attaches to regulator. Apply several drops of solution where regulator connects to cylinder. Make sure all patio heater valves are OFF. Turn cylinder valve ON. IF BUBBLES APPEAR AT ANY CONNECTION, THERE IS A LEAK. 1. Turn cylinder valve OFF. 2.
OPERATING INSTRUCTIONS Lighting: NOTE: For initial start or after any cylinder change, hold the control knob in for 2 minutes to purge air from all gas lines before proceeding. NOTE: This heater has an Electronic Ignition and will require installation of 1 – AAA battery. The battery should be installed by unscrewing the RED IGNITER BUTTON. 1. Turn the control knob to the “OFF” position. 2. Fully open the LP cylinder valve. 3.
OPERATING INSTRUCTIONS Operation Checklist: For a safe and pleasurable heating experience, perform this check before each use: Before Operating: 1. I am familiar with entire owner’s manual and understand all precautions noted. 2. All components are properly assembled, intact and operable. 3. No alterations have been made. 4. All gas connections are secure and do not leak. 5. Wind velocity is below 10 mph. 6. Unit will operate at reduced efficiency below 40 degrees F. 7.
CARE AND MAINTENANCE Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water if any carbon deposits develop. Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal.
TROUBLESHOOTING If you have any questions regarding this product, please call our customer service hotline at 1-866-985-7877, 9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net. PROBLEM POSSIBLE CAUSE Gas valve may be off Main burner will not light Low burner flame CORRECTIVE ACTION Turn gas valve ON Fuel tank may be empty Refill LPG tank Orifice blocked Clean or replace orifice Air in supply system Purge air from lines.
Distributed By: Well Traveled Living 716 S 8th Street Amelia Island, FL 32034 Toll Free: 866-WTL-SUPP (866-985-7877) Web: www.wtliving.com Email: cservice@welltraveled.net LIFETIME WARRANTY For the life of the product, all components are warranted against defects in materials and workmanship under normal use. Well Traveled Living will repair or replace defective parts for the life of the product.