Outdoor Patio Heater Item#60368,60485,60786,60788,61185,61444,61546,61547, 61629,61726,61727,61728,61729,61730,61735,61736,61737, 61738,61739,61740,61741,61742,61743 ATTACH YOUR RECEIPT HERE Serial Number ___________ Purchase Date ______ Manufacturer: Changzhou Wellife Furnace Co., Ltd. Questions, problems, missing parts? Before returning to your retailer, call our customer service hotline at 1-866-985-7877, 9 a.m. – 6 p.m., EST, Monday – Friday or email at cservice@welltraveled.net.
TABLE OF CONTENTS Table of Contents………………………………….....................Page 2 Before You Begin............................................................Page 2 Safety Information.........................................................Page 3-4 Package Contents………………………………….....................Page 5 Hardware Contents..........................................................Page 6 Assembly.........................................................................Page 6-10 Operating Instructions……………......
SAFETY INFORMATION 3
SAFETY INFORMATION 4
PACKAGE CONTENTS ASSEMBLY PART DESCRIPTION QTY 4 pcs (packed in 2 inner ctns) A Reflector Panel B Reflector Center Cap 1 C Head Assembly 1 (packed in 1 inner ctn) D Tank Housing 1 E Gas Hose 1 (attached to Head Assembly) F Upper Post 1 G Lower Post 1 H Regulator I Post Supports *J *Base K Wheel Assembly L Chain (to secure LPG cylinder) 1 (packed with Head Assembly) 3 (packed in 1 inner ctn) 1 1 (packed with Head Assembly) 1 (packed with post supports) *Some models come wit
HARDWARE CONTENTS ASSEMBLY ASSEMBLY PREPARATION Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package contents list and hardware contents as listed on pages 5 and 6 of this manual. If any part is missing or damaged, do not attempt to assemble this product. Contact customer service for replacement parts.
ASSEMBLY 1. Attach Wheel Assembly (K) to Base (J). Align holes in Wheel Assembly with corresponding holes in Base, and insert 2 - Small Bolts through holes and finger tighten. Be sure that Wheel Assembly is parallel to the Base (J) and tighten with wrench. 1 Hardware Used: 2 x Small Bolt *Optional sandbox: For models that come with a sandbox, the sandbox will be pre-assembled to the base. To fill the sandbox, remove the 4 Large Screws and Large Nuts that secure the base to the sandbox.
ASSEMBLY 3. Attach the Lower Post (G) to the Post Supports (I). Once you 3 have tightened the bolts holding the Post Supports (I) to the Base (J), align the holes in the Lower Post (G) with the holes on the tops of the Post Supports (I) and insert a Large Bolt through the hole in the Post Support. Secure with a Small Flange Nut. Repeat this in the 5 remaining holes (6 holes total—2 for each Post Support piece). Hand tighten initially then tighten with a wrench when all bolts have been inserted.
ASSEMBLY 6. Attach Reflector Studs to the top of the Head Assembly (C). Insert 1 Reflector Stud through 1 Large Flat Washer and into hole on the top of the Head Assembly (C). Tighten stud securely. Repeat with the other 2 Reflector Studs. 6 Hardware Used: 3 x Reflector Stud 3 x Large Flat Washer 7. Attach Head Assembly (C) to Upper Post (F). Route Gas Hose (E) down into Upper/Lower post assembly and align 4 small holes on Head Assembly with 4 Small holes in Upper Post (F).
ASSEMBLY 9. While supporting heater, tilt the Head Assembly (C) and slide 3 Large Flat Washers over the Reflector Studs. Place the Reflector Assembly onto the Reflector Studs and slide 3 Large Flat Washers over the Reflector Studs and onto the Reflector Assembly. Secure with 3 Wing Nuts . Once you have tightened the Wing Nuts, return the heater to an upright position. 9 Hardware Used: 6 x Large Flat Washer 3 x Wing Nut 10. Connect the hose and regulator to the LP cylinder.
OPERATING INSTRUCTIONS A minimum supply pressure of .5 psi is required for the purpose of input adjustment of propane gas. Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance. A cylinder must be stored outdoors in a well-ventilated area out of the reach of children. A disconnected cylinder must have dust caps tightly installed and must not be stored in a building, garage, or any other enclosed area.
OPERATING INSTRUCTIONS Leak Test 1. 2. 3. 4. 5. Make 2-3 oz. of leak test solution (one part liquid dishwashing detergent and three parts water). Apply several drops of solution where hose attaches to regulator. Apply several drops of solution where regulator connects to cylinder. Make sure all patio heater valves are OFF. Turn cylinder valve ON. IF BUBBLES APPEAR AT ANY CONNECTION, THERE IS A LEAK. 1. Turn cylinder valve OFF. 2.
OPERATING INSTRUCTIONS Lighting: NOTE: For initial start or after any cylinder change, hold the control knob in for 2 minutes to purge air from all gas lines before proceeding. 1. Turn the control knob to the “OFF” position. 2. Fully open the LP cylinder valve. 3. Push in and turn the control knob half way between the HI and LO symbols. 4. Push control knob in and then push the RED igniter button to ignite the main burner. Repeat until the burner ignites.
OPERATING INSTRUCTIONS Shut Down: 1. Turn control knob clockwise to OFF while depressing the knob. (Normally, burner will make a slight popping noise when extinguished). 2. Turn cylinder valve clockwise to OFF and disconnect regulator when heater is not in use. NOTE: After use, some discoloration of the emitter screen is normal. Operation Checklist: For a safe and pleasurable heating experience, perform this check before each use: Before Operating: 1.
CARE AND MAINTENANCE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Keep exterior surfaces clean. 1. Use soapy water for cleaning. Never use flammable or corrosive cleaning agents. 2. While cleaning your unit, be sure to keep the area around the burner and control compartment dry at all times. Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be replaced. 3.
TROUBLESHOOTING If you have any questions regarding this product, please call our customer service hotline at 1-866-985-7877, 9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net. PROBLEM Main burner will not light POSSIBLE CAUSE Gas valve may be off Turn gas valve ON Fuel tank may be empty Refill LPG tank Orifice blocked Clean or replace orifice Air in supply system Purge air from lines. Open gas lines and depress control knob for 2-3 mins.
REPLACEMENT PARTS LIST ASSEMBLY For questions regarding this product or to purchase replacement parts, please call our customer service hotline at 1-866-985-7877, 9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net.
Distributed By: Well Traveled Living 716 S 8th Street Amelia Island, FL 32034 Toll Free: 866-WTL-SUPP (866-985-7877) Web: www.wtliving.com Email: cservice@welltraveled.net 1 YEAR LIMITED WARRANTY – Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use.