. .
TOOLS AND PARTS NEEDED FOR ASSEMBLY DANGER WARNING:Improper installation, adjustment, alteration, services or maintenance can cause injury, death or property damage. Read the installation, operating and maintenance instructions thoroughly before CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in a enclosed space such as a camper, tent, car or home.
PARTS 1 ● 2 ● 3 ● 4 ● 5 ● 6 ● 7 ● 8 ● 9 ● 10 ● 11 ● 12 ● 13 ● 14 ● 15 ● 16 ● 17 ● 18 ● 19 ● 20 ● 21 ● 22 ● 1 Center Reflector Cap 3 Reflector Pieces 1 Head Assembly 1 Gas hose attached to head assembly 3 1 Upper Post 1 Lower Post 1 Cylinder Cover 3 Post Mounts 1 Cylinder Base 1 Post Support 3 M8 Wing nuts 6 M8 Washers 9 M6 Screw Cap 9 M6x8 Bolts 4 M5x10 Bolts and 4pcs lock washer 4 M6x10 Bolts 6 M6X18 Bolts 6 M6 Screw Cap 1 Regulator 3 M8x90 Double Pointed Bolts 3 M8X16 Bolts 6pcs M6x12mm bolts/washers/nu
PRECAUTIONS NOTE: PLEASE READ THE FOLL OWING SAFETY RULES WARNING: At least once a year, the unit should be inspected for This appliance must only be used outdoors. the presence of spiders, spider webs or other insects. Using this product in an enclosed area may cause Check the heater immediately if any of the following injury, death or property damage. exist: Read the instructions before use. 1.
ASSEMBLY ATTACHING WHEEL ASSEMBLY Step 1 1-1. Locate Wheel Assembly (24) and 2 nuts/bolts contained in Fig. 1 plastic bag with Wheel Assembly (Fig. 1). Step 2 Fig. 2 2-1. Turn Base (9) so that holes for attachment of Wheel Assembly are facing you (Fig. 2). 2-2. Align holes in Wheel Assembly (24) with holes on Base (9) (Fig. 3).Insert bolts through both sets of holes and secure nuts on end of bolt (Fig. 4). Fig. 3 Fig. 4 Step 3 3-1. Wheel Assembly (24) should now be attached to Base (9) as shown (Fig.
ASSEMBLY WARNING: Proper assembly is the responsibility of the installer. STEP 1 Step 1 Attach 3pcs LPG cylinder fixed parts on the base with 6pcs M6x12mm bolts/washers/nuts. * M8x25mm bolts are already in fixed parts for holding cylinder. Attach post mounts to cylinder base: Place the post mounts on the top of cylinder base, and connect them using 3pcs M8x16 bolts.
ASSEMBLY Step 2 Attach post support to post mounts: Place the post support on the top of post mounts and attach to post mounts using 6pcs M6x18 screw bolts and 6pcs M6 screw caps. STEP 2 STEP 3 Step 3 Attach lower post to base assembly: Attach the lower post to the post mounts using 4pcs M6x10 bolts.
ASSEMBLY Step 4 Attach upper post to lower post: Screw the upper post to the lower post as illustrated by turning in a clockwise direction until securely tightened. Step 4 Step 5 Step 5 Attach cylinder cover to post mounts.
ASSEMBLY Step 6 Attach double pointed bolts to head assembly: Attach M8x90 double pointed bolts (3pcs) to head assembly. Step 7 Step 7 Route the gas hose down through the post and out of the bottomthen connect the regulator with gas hose Finally connect the head assembly with post with 4pcs M5x10 bolts and 4pcs lock washer.
ASSEMBLY Reflector (#2) is comprised of 3 – outer pieces and 1 – center piece. Locate all 4 pieces of Reflector (#2) which are wrapped in bubble wrap. Unwrap and remove all pieces and peel off the protective blue plastic on each piece. Locate 9 bolts and 9 cap nuts in the plastic bag. Align the 3 – outer pieces with the 1 – center piece and place a bolt through the center hole on each piece as shown below. Tighten castle nut on each bolt.
ASSEMBLY Step 8 Attach the reflector to the top head assembly: Attach 3pcs M8 washers on the top of 3pcs double pointed bolts. Place assembled reflector on the top of double pointed bolts and secure with 3pcs M8washers and 3pcs M8 wing nuts. Step 9 Connect gas hose to cylinder (20lb.cylinder is not supplied): Attach regulator to cylinder. Tighten securely. Put gas cylinder on base. Adjust bolts in cylinder fixed parts. Note: The regulator with gas hose is supplied.
ASSEMBLY Step 10 Put the cylinder on the base: Attach the cylinder to the base with 3pcs M8x25 bolts and tighten it in order to prevent the cylinder from moving. Step 10 Warning: The cylinder used must include a collar to protect the cylinder valve. Do not store a spare LP Gas cylinder under or near this appliance. Never fill the cylinder beyond 80 percent full. For appliances designed to use a CGA No.791 connection: Place the dust cap on the cylinder valve outlet whenever the cylinder is not in use.
ASSEMBLY Step 12 Lower the cylinder cover onto cylinder base. Step 13 Disconnect cylinder when storing or transporting: 1. Turn off the heater. 2. Turn off the valve of the cylinder. 3. Lift the cylinder cover above the post mounts. 4. Loosen the screw of cylinder and regulator. 5. Disconnect the cylinder from regulator. Step 13 The installation must conform with local codes or, in the absence of local codes, with the most current version of the National fuel gas code, ANSI Z223.
OPERATION WARNING: DO NOT attempt to operate heater until you have read and understood all precautions. Failure to do so can result in serious personal injury, death and/or property damage. Before turning gas supply ON Your heater was designed and approved for OUTDOOR USE ONLY . DO NOT use it inside a building, or any other enclosed area. Make sure surrounding areas are free of combustible materials, gasoline and other flammable vapors or liquids. Ensure that there is no obstruction to air ventilation.
OPERATION CAUTION: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will apper. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the “LOW” position, then turn the knob to the level of heat desired.
LOCATION OF HEATER FOR USE WARNING: WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT ABOVE, BESIDE, OR UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. This heater is primarily used for the heating of outdoor patios, decks, spas, pools and open working areas. Always make sure that adequate fresh air ventilation is provided. Follow the spacing tolerances shown in Figure 1. The minimum clearances, shown in Figure 1 must be maintained at all times.
MAINTENANCE / STORAGE Check your hose assembly: The installation of fixed appliance shall only be carried out by competent persons and be in accordance with the relevant codes of practice. Warning: This appliance requires a gas hose and regulator. Check with your gas supplier and or product supplier. Regularly check the gas hose and if necessary, replace the gas hose. Prior to use, check for damaged parts such as hoses, regulator, pilot or burner.
MAINTENANCE / STORAGE STORAGE: Between uses: Turn the control knob to “OFF” position. Turn LPG cylinder to “OFF” position. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail ,snow, dust and debris). If desired, cover heater to protect exterior surfaces and or help prevent debris in air passages. During periods of extended inactivity or when transporting: Turn the control knob to “OFF” position.
TROUBLESHOOTING PROBLEM Pilot will not light Pilot will not stay on Burner will not light PROBABLE CAUSE SOLUTION Gas valve may be OFF Turn the gas valve ON Fuel tank empty Refill LP gas tank Orifice blocked Clean or replace orifice Air in supply system Purge air from lines Loose connection Check all fittings Debris around pilot Clean dirty area Loose connection Tighten connection Thermocouple bad Replace thermocouple Gas leak in line Check connection Lack of fuel pressure Fuel tank
- 20 -