R IRSTROKE ACTUATORS ACTUATORS Airstroke actuators/Airmount isolators IRMOUNT IRMOUNT R IS OLATORS OLA TORS SOLATORS ® ® EMDG 198 EMDG 198 Engineering Manual & Design Guide
TABLE OF CONTENTS Table of Contents and Introduction...............................2 Advantages of Airstroke Actuators ...............................3 Advantages of Airmount Isolators.................................4 Air Spring Bellows Construction ...................................5 End Closure Options Crimped bead plates..................................................6 Crimped bead plates mounting hardware .................7 Steel bead rings.........................................................
ADVANTAGES OF FIRESTONE AIRSTROKE ACTUATORS ® Why use an Airstroke actuator (rather than air or hydraulic cylinder) for actuation? LOW COST Generally, initial cost is one-half or less than conventional pneumatic or hydraulic cylinders of the same force capabilities. This initial cost advantage is many times greater in the larger sizes. WIDE SIZE RANGE Airstroke actuators are available in sizes ranging from 2.2 inches to 37 inches in diameter. The force capability is 100,000 pounds.
ADVANTAGES OF FIRESTONE AIRMOUNT ISOLATORS ® Why use an Airmount isolator rather than a coil spring or other type of isolator? UNSURPASSED ISOLATION CAPABILITY Airmount isolators can provide the highest degree of isolation of any type vibration isolator. System natural frequencies as low as 60 cycles per minute (1 Hertz) are available. The addition of an auxiliary reservoir can provide even lower system frequencies.
AIR SPRING BELLOWS CONSTRUCTION OUTER COVER SECOND PLY FIRST PLY INNER LINER An air spring is a carefully designed rubber/fabric bellows which contains a column of compressed air. The rubber bellows itself does not provide force or support load. This is done by the column of air. Firestone air springs are highly engineered elastomeric bellows with specially designed metal end closures. Our standard two ply air spring bellows is actually made up of four layers: a. An inner liner of calendered rubber. b.
END CLOSURE OPTIONS Each individual air spring data sheet shows a cross sectional view of the most popular end closure option for that part. For convoluted air springs 16 inches in diameter and less, and for the reversible sleeve air springs, the Crimped Bead Plate attachment is shown. For convoluted air springs 17 inches in diameter and larger, a Bead Ring attachment is shown. An air spring of each variety, with proper terminology for each, is shown on the following pages.
CRIMPED BEAD PLATE MOUNTING HARDWARE CRIMPED BEAD PLATE AIR SPRINGS Use the blind nuts for attachment. This is accomplished by bringing bolts (two or four depending upon air spring size) through the customer supplied mountIng plate and tightening into the blind nut. If this bolt is too long, it may fracture the bottom out of the blind nut. To Air Supply 3/8-16 UNC Blind Nut, 5/8" Deep Customer Supplies Mounting Plates Bolts & Washers 5/8" 5/8" Tightening Torque on the blind nut: 15 to 20 ft.-lbs.
END CLOSURE OPTIONS STEEL BEAD RINGS CONVOLUTED AIR SPRINGS (#22 is shown, with bead rings instead of crimped bead plates) MOUNTING PLATE is not included. See page 10 for material, machining recommendations, and installation instructions. BEAD RING BOLT May be one of four varieties. See page 10. Also refer to the data sheet order block on each individual part for bolt lengths. NUTS AND LOCKWASHERS are included with the part. (Except for socket head type bead rings).
END CLOSURE OPTIONS LARGE PARTS WITH ALUMINUM BEAD RINGS All of the parts that are shown with crimped bead plates are also available with bead rings. (Bead plates are not suitable for some applications.) Typical examples of where bead rings are often used follow: 1. Where parts are stacked to increase stroke (See page16). 3. When used as an Airmount isolator with an auxiliary reservoir (See page 24). 4.
END CLOSURE OPTIONS THE FOUR TYPES OF BEAD RINGS BUTTON HEAD STEEL BEAD RING COUNTERSUNK STEEL BEAD RING SOCKET HEAD ALUMINUM BEAD RING* RIBBED NECK ALUMINUM BEAD RING Used on 4.5 in. Bolt Circles Use M6 Cap Screws, (Not Included) Customer Supplies Plate Bolt Length Effective Length Bolt Length Effective Length Customer Supplies Plate Bolt Length Customer Supplies Plate Effective Length Optional Shorter Length Ribbed Neck Bolt Standard Bolt Length (in.) 1 7/8 Standard Bolt Length (in.
END CLOSURE OPTIONS LARGE PARTS WITH ROLLED PLATES LARGE CONVOLUTED AIR SPRINGS (#203 is shown, with rolled plates instead of bead rings) The convoluted parts, with 17, 20, and 22 inch diameter, are shown with bead rings as standard. We have developed a method for permanently attaching plates to these larger sized Airstrokes (called rolled plate assembly).
HOW TO USE THE STATIC DATA CHART We also refer to this chart as the load/deflection (L/D) curve for an air spring. The force [1] is given on the right hand axis vs. the air spring height [2] as shown along the bottom axis; thus, load vs. deflection. The internal volume [3] is also given along the left hand axis, again vs. height [2]. It is called static data because the air spring is in a static, or non-moving, constant pressure condition.
(There is one exception: notice the plateau section of reversible sleeve 1T type curves). In the example the effective area of a #22, at 4.0 inches using the 80 psi curve, is: 7,180 lbs. = 89.8 in2 80 Ibs/in2 at 9.0 inches in height it is: 4,670 lbs. = 58.4 in2 80 Ibs/in2 An air cylinder with 89.8 in2 of area would have an 80 psi curve as shown by dotted line [10]. The volume curve [3] may also be of importance: a.
BASIC PARAMETERS APPLICABLE TO BOTH AIRSTROKE ACTUATORS AND AIRMOUNT ISOLATORS ® ® MEDIA TEMPERATURE Air springs are designed for use with compressed air. Nitrogen is also acceptable. Air springs may be filled with water or waterglycol (automotive antifreeze) solutions. If water is to be used, rust inhibitors should be added to protect the end closures. Two reasons for liquid filling an air spring are: 1. STANDARD BELLOWS.
AIRSTROKE ACTUATION SELECTION 1. Refer to the selection guide on page 32 for Airstroke force and stroke capabilities. After your list of possibilities has been reduced to one or two air springs, then turn to the individual data page for more detailed information on those parts. 2. STROKE: The maximum STROKE CAPABILITY is the difference between the height corresponding to the “start of the shaded area” minus the minimum height. This entire stroke, or any portion thereof, may be used.
Angular Capability continued These measurements must fall within the guide lines for that particular part. Consider style #22 in the following scissors arrangement: Calculate Force Here Max Ht (Must be ≥ 3.0) #22 Please note that the air spring forces are not additive in this configuration. A method for guiding, which also illustrates one center ring concept for mounting the two parts together at the middle, is illustrated below: Max Ht (Must be ≤ 10.
16.5 11 6 18 12 6.5 REFER TO EACH INDIVIDUAL DATA PAGE FOR MAXIMUM USABLE HEIGHT RESTRICTIONS 5.5 10 15 SINGLE CONVOLUTED 3.5 DOUBLE CONVOLUTED 4.5 4 9 6 10.5 TRIPLE CONVOLUTED 8 7 12 OVERALL AIRSTROKE HEIGHT (INCHES) 5 9 13.5 TYLE ING S R D A D BE TE AN A STYLE L E P T D A A L E TWO PLY B ED P ROLL D BEA Y L RP FOU 3 5 7.5 BEAD RING STYLE AND E T PLA 2.5 4 6 BASED ON APPROXIMATELY 1/3 NORMAL BURST VALUES APPLICATIONS WHICH EXCEED THESE LIMITS SHOULD BE REVIEWED WITH FIRESTONE.
® AIRSTROKE ACTUATOR PROBLEM SOLVERS GLUING PRESS GATE VALVE OPERATOR DIE STRIPPER WEB TENSIONING DEVICE AIRSTROKE ACTUATOR PAPER KNIFE SPRING ACTUATOR QUENCH TANK ACTUATOR ROTATION KNIFE LOG QUENCH TANK AIRSTROKE ACTUATORS UPPER & LOWER POSITIVE STOPS PAPER SIZING PRESS PICKLING TANK ACTUATOR AIR LINES PRESS PIVOT ACID TANK FRAME QUICK LOCK DEVICE 18 ACID WIRE COILS PRESSURE ROLL FOR CALENDER
® AIRSTROKE ACTUATOR PROBLEM SOLVERS MISSILE ASSEMBLY FIXTURE CORE STRAIGHTENER AIRSTROKE ACTUATOR BELT TAKE UP ROLLER FRICTION BRAKE FRICTION PAD AIRSTROKE ACTUATOR PIPE INDEXING THREADING END VIEW OF PIPE OSCILLATING DOCTOR FOR PAPER CALENDER ROLL DOCTOR CYLINDER FORMING PRESS CABLE TENSIONING DEVICE PRESS PLATEN TORSIONAL FRICTION BRAKE BAG FLATTENER POWERED ROLLER BAG OF MATERIAL TO BE FLATTENED DRIVE BELT LINESHAFT AIRSTROKE ACTUATOR ROLLER SUPPORT FRAME TORQUE TUBE AIRSTROKE ACTUATOR
® AIRSTROKE ACTUATOR PROBLEM SOLVERS HINGED GATE HOT FOIL STAMPING PRESS AIR FITTING AIRSTROKE ACTUATOR AIRSTROKE ACTUATOR WEIGH HOPPER COMPRESSED POSITION EXTENDED POSITION TORSION SPRING HINGE CLOSED OPEN ACTUATED HEAVY DUTY SEALER PIVOTED CLAMPING DEVICE AIRSTROKE ACTUATOR AIRSTROKE ACTUATED ROLLER STOP ADJUSTABLE COLLAPSE HEIGHT RUBBER STOP AIRSTROKE ACTUATOR HINGED ACTUATED GRAVITY GATE AIRSTROKE ACTUATOR RETURN TENSION SPRING VERTICAL ACTUATED DRIVE TABLE TOP OF CHAIN IN HIGH POSITION
AIRMOUNT VIBRATION ISOLATION ® SELECTION AND ISOLATION FORMULA CONSIDER THIS EXAMPLE: Refer to the selection guide on page 33 for Airmount load and isolation capabilities. Follow this procedure: Isolate a vibrating screen which weighs a total of 16,400 pounds, preferably with one isolator at each corner. The vibrating mechanism is rotating at a speed of 850 rpm (cpm) with a total stroke of 5/16 inch. 1. LOAD CAPACITY Select one or two Airmounts that can support the load at each mounting point.
AIRMOUNT VIBRATION ISOLATION ® b) What exact isolation will be attained? Consider the same #22 example: What is the vertical spring rate with a load of 4,100 pounds at a design height of 9.5 inches? Refer to the static data chart on page 61. Again, our “closest" pressure is 80 psig, so we'll need to read the appropriate data from the 80 psig curve.
AIRMOUNT VIBRATION ISOLATION ® Up to this point, only the weight and disturbing frequency have been discussed. THERE ARE MANY OTHER IMPORTANT CONSIDERATIONS: CENTER OF GRAVITY An Airmount isolation system is inherently soft (easily deflected); therefore, precautions must be taken to insure that the system is stable. First, consider the location of the center of gravity (c.g.). Ideally, the Airmounts should be located on the same plane (parallel to the ground) as the center of gravity.
AIRMOUNT VIBRATION ISOLATION ® At design height and without an auxiliary reservoir, the single and double convoluted parts follow this pattern; i.e., the lateral rate varies from 1/5 to 1/ 2 of the vertical rate (only the larger high strength parts get as high as 1/2). Notice the #22 is 325 approximately 1/4(1,373 ). Going back to the original example of a vibrating screen which weighs 16,400 Ibs. mounted on four #22’s (@ 9.
AIRMOUNT VIBRATION ISOLATION ® DAMPING need for periodic inspections. The air springs should always be connected in clusters so the mass is supported with only THREE REGULATORS. This is illustrated below (in the previous column) for both a four and eight Airmount system: C Damping is defined as the ratio: C c WHERE: C = System Damping Cc = Critical Damping The damping ratio inherent in an Airmount is in the order of .03.
AIRMOUNT VIBRATION ISOLATION ® CPM 3000 2500 2000 FORCED FREQUENCY (ff) 99.9 25 1500 16.7 15 13.3 11.7 10 8.3 99.5 99 98 97 96 95 90 80 70 60 1000 900 800 700 600 500 Re so na nc e HERTZ 50 41.7 33.2 P Iso erc lat ent ion ISOLATION CHART 6.7 400 5.0 300 4.2 250 Amplification 3.3 200 2.5 150 1.7 100 30 40 50 60 80 100 0.50 0.67 0.83 1.0 1.33 1.67 150 200 2.50 3.33 300 400 500 600 800 1000 CPM 5.00 6.67 8.33 10.0 13.3 16.
® AIRMOUNT ISOLATION PROBLEM SOLVERS VIBRATING PACKER BIN HOPPER COMPRESSOR COMMERCIAL LAUNDRY MACHINE 27
® AIRMOUNT ISOLATION PROBLEM SOLVERS CONTROL BOOTH VIBRATING SCREEN BLOWER AND MOTOR CONTROL PANEL 28
MISCELLANEOUS APPLICATIONS The air spring provides a unique solution for many actuation and isolation applications the world over. Besides the common applications, there are many that are not readily recognized because of the air spring’s unique construction. Listed below are some miscellaneous applications. SHOCK IMPACT ISOLATION The air spring is frequently used in shock impact isolation applications.
MISCELLANEOUS PROBLEM SOLVERS ROBOTIC COUPLING CONVEYOR END STOP AIRSTROKE END VIEW 30 MOUNTAIN/TRAIL BIKE SHOCK ABSORBER TEST SYSTEM SCREENING MACHINE COVER CLAMP PIPE CRAWLER DELICATE ELECTRONIC EQUIPMENT VIBRATING SCREEN
MISCELLANEOUS PROBLEM SOLVERS SHEET WELDING CLAMP PERFECT BOUND MAGAZINE CUTTER SWASH PLATE MOTOR WAVE POWER MODULE CHECK VALVE LAPPING SELF ALIGNING DEVICE AIR BLAST GENERATOR SOLAR TRACKER 31
SELECTION GUIDE ® END CLOSURE OPTIONS AIRSTROKE ACTUATORS Style Number Maximum Maximum Diameter Minimum Maximum Usable Stroke at 100 PSIG Height Height (inches) (inches) (inches) (inches) 80 PSI Force* at Stroke of 1 Inch 3 Inches Maximum Stroke (pounds) (pounds) (pounds) High Strength Style Number Bead Plate Type Dim. A (blind nut centers) (inches) Dim. B (inches) Bead Ring Type Dim. C Number (bolt circle of Bolts diameter) (each (inches) ring) SHAPED SLEEVE 1M1A-0 1M1A-1 2M1A 2M2A 3.4 3.45 3.
® END CLOSURES AIRMOUNT ISOLATORS Style Number Design Height Load (at Design Height) at: ••40 PSIG (pounds) 60 PSIG (pounds) 80 PSIG (pounds) Natural Frequency (@ 80 PSIG) fn(cpm) % of Isolation at Forced Frequency 400 CPM 800 CPM 1500 CPM % % % TYPE 1 bead plate SHAPED SLEEVE 1M1A-0 1M1A-1 2M1A 2M2A 2.5 3.0 210 235 330 450 220 356 475 162 90.0 DO NOT USE 2M1A AS AN AIRMOUNT ISOLATOR 105 137 232 91.8 95.5 97.8 98.6 2.0 73 90.8 97.
1M1A-0 Description RECOMMENDED AIRMOUNT DESIGN HEIGHT 2.5 INCHES Assembly Order No. Style Blind nut, 1/8 NPT, 1M1A-0 plastic stud Blind nut, 1/8 NPT, Two brass stud Ply Bellows Blind nut, 1/8 NPT, brass stud, stainless steel ring Static Data 8470 WO2-358-3000 Do not use Airstroke in shaded area without consulting Firestone WO2-358-3001 WO2-358-3005 14 120 Psig 7 Volume 60 Psig Assembly weight ........................................................ 0.5 lbs.
1M1A-1 Description Assembly Order No. Style Blind nut, 1/8 NPT, 1M1A-1 brass stud RECOMMENDED AIRMOUNT DESIGN HEIGHT 3.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT WO2-358-3003 Static Data B3940 24 12 Two Ply Bellows Volume 100 Psig Assembly weight ........................................................ 0.5 lbs. 20 5/16-18 THREADED HOLE (3/8 DEEP) 3-5 TURNS 30-50 IN. LBS. TORQUE 3.4 MAX O.D. AT 60 PSIG 2.88 DIA. HEIGHT 5/8-11 1.00 100-130 IN. LBS.
2M1A Static Data AIRSTROKE ACTUATOR ONLY 8469 Description Style 2M1A Two Ply Bellows Assembly Order No. 1/8 NPT, each end, plastic studs 1/8 NPT, each end brass studs WO2-358-3002 Do not use Airstroke in shaded area without consulting Firestone WO2-358-3004 120 Psig 7 Assembly weight ........................................................ 0.6 lbs. 3.5 MAX O.D. AT 60 PSIG 5/8-11 100-130 IN. LBS.
2M2A RECOMMENDED AIRMOUNT DESIGN HEIGHT 1.8 INCHES Assembly Order No. Blind nut,1/8 NPT, plastic studs WO2-358-3008 B6575 30 6 Two Ply Bellows Do not use Airstroke in shaded area without consulting Firestone Assembly weight. . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 lbs. 25 Volume 100 Psig 1/8 NPT AIR INLET HAND TIGHT PLUS 1 TURN 2.3 MAX O.D. AT 60 PSIG 1.34 DIA. 5/8-11 100-130 IN. LBS. TORQUE .75 HEIGHT VOLUME (WITHOUT BUMPER) CU IN.
16 Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-7001 WO1-358-6996 Two Socket head aluminum bead Ply rings (bolts, nuts, washers not Bellows included-use 1/4 cap screws) WO1-358-0017 3/4 NPT (only) upper plate, blind nuts lower plate Rubber bellows only WO1-358-0286 WO1-358-0010 Assembly weight ........................................................ 2.5 lbs. Force to collapse to minimum height (@ 0 PSIG)....... 30 lbs. 3/8-16 BLIND NUTS (5/8 DEEP) 15-20 FT. LBS. TORQUE 1/4 NPT AIR INLET 1.75 6.
16-ST Description Blind nuts, 1/4 NPT Stainless steel plates WO2-358-5000 WO2-358-5002 Static Data B4165 32 Two Ply Bellows 30 28 Assembly weight ...................................................... 1.25 lbs. Force to collapse to minimum height (@ 0 PSIG)...... 8.0 lbs. 15-20 FT. LBS. TORQUE VOLUME (WITHOUT BUMPER) CU IN. 3/8-16 UNC 1/4 NPT 1.
131 Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-7731 WO1-358-7742 Two Socket head aluminum bead Ply rings (bolts, nuts, washers not Bellows included-use 1/4 cap screws) 3/4 NPT (only) upper plate, blind nuts lower plate Rubber bellows only WO1-358-0127 Static Data 6512 26 Do not use Airstroke in shaded area without consulting Firestone 6 25 Force to collapse to minimum height (@ 0 PSIG)....... 32 lbs. 3/8-16 BLIND NUTS (5/8 DEEP) 1/4 NPT AIR INLET 1.75 6.5 MAX O.D.
110 Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-7451 WO1-358-7484 Two Socket head aluminum bead Ply rings (bolts, nuts, washers not Bellows included-use 1/4 cap screws) Rubber bellows only RECOMMENDED AIRMOUNT DESIGN HEIGHT 4.5 INCHES 19 WO1-358-0112 WO1-358-0100 1.75 8.3 MAX O.D. AT 100 PSIG HEIGHT 16 VOLUME (WITHOUT BUMPER) CU IN. x 10 15-20 FT. LBS. TORQUE 120 Psig 17 Force to collapse to minimum height (@ 0 PSIG)......... 8 lbs.
116 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT Two Button head steel bead rings, Ply 15/8 bolts, nuts, washers Bellows Blind nuts with installed 1/4 tank valve Rubber bellows only WO1-358-7564 WO1-358-7561 Style 116 RECOMMENDED AIRMOUNT DESIGN HEIGHT 4.
116-1 Style 116-1 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-7598 WO1-358-7605 RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.5 INCHES Static Data 8776 Volume 100 Psig Two Ply Bellows 120 Psig Do not use Airstroke in shaded area without consulting Firestone Assembly weight ........................................................ 4.5 lbs. Force to collapse to minimum height (@ 0 PSIG)....... 37 lbs. 15-20 FT. LBS. TORQUE 1/4 NPT AIR INLET 2.75 9.6 MAX O.D.
115 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT rubber bumper Two Ply Blind nuts, 3/4 NPT Bellows Blind nuts, 3/4 NPT rubber bumper Countersunk steel bead rings, 15/8 bolts, nuts, washers Blind nuts, 3/4 NPT both ends (centered) Rubber bellows only WO1-358-7460 5 WO1-358-7650 WO1-358-7649 1.75* *(1.50 FOR 3/4) 100 Psig Volume 100 Psig 4 2 80 Psig 3 60 Psig 1 2 40 Psig 1 3.50 20 Psig 10.1 MAX O.D. AT 100 PSIG HEIGHT OPTIONAL BUMPER MAX. HT. 6.31 DIA.
19 Description Style 19 Two Ply Bellows RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.0 INCHES Assembly Order No.
19-.75 Description RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.5 INCHES Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT rubber bumper Two Ply Blind nuts, 3/4 NPT Bellows Blind nuts, 3/4 NPT rubber bumper Style 19-.75 WO1-358-7040 WO1-358-7039 WO1-358-7042 Static Data 4043 Do not use Airstroke in shaded area without consulting Firestone 120 Psig 11 WO1-358-7043 Assembly weight ...................................................... 10.0 lbs. 5 10 1/4 or 3/4 NPT AIR INLET 2.88 15-20 FT. LBS.
113 Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Button head steel bead rings, 17/8 bolts, nuts, washers Blind nuts, 1/8 NPT Blind nuts, 11/4 NPT Rubber bellows only WO1-358-7103 WO1-358-7104 WO1-358-7101 WO1-358-7109 Style 113 WO1-358-7110 WO1-753-7113 WO1-753-7114 WO1-358-0135 Assembly weight ...................................................... 14.5 lbs. Force to collapse to minimum height (@ 0 PSIG)....... 17 lbs.
113-1 Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT Two Blind nuts, 3/4 NPT, Ply rubber bumper Bellows Button head steel bead rings, 17/8 bolts, nuts, washers Rubber bellows only WO1-358-7091 WO1-358-7092 Style 113-1 RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.5 INCHES WO1-358-7277 WO1-358-0150 3/8-16 BLIND NUTS (5/8 DEEP) WO1-358-8160 1/4 or 3/4 NPT AIR INLET 6.25 15-20 FT. LBS. TORQUE 6.25 17 8 VOLUME (WITHOUT BUMPER) CU IN.
153-2 Style 153-2 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-8158 WO1-358-8157 RECOMMENDED AIRMOUNT DESIGN HEIGHT 6.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data B4561 14 Two Ply Bellows 28 Do not use Airstroke in shaded area without consulting Firestone 13 26 12 24 3.12 6.25 15-20 FT. LBS. TORQUE 6.25 18.1 MAXIMUM O.D.
119 RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.0 INCHES Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers Two Rubber bellows only Ply Bellows Rolled Plate Assembly, 1/2 blind nuts, 3/4 NPT Style 119 WO1-358-7478 WO1-358-0119 120 Psig 10 VOLUME (WITHOUT BUMPER) CU IN. x 100 28-32 FT. LBS. TORQUE 13.81 BOLT CIRCLE DIA. 17.4 MAX O.D. AT 100 PSIG HEIGHT 20 Volume 100 Psig Force to collapse to minimum height (@ 0 PSIG)....... 17 lbs.
121 RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.0 INCHES Assembly Order No. Ribbed neck aluminum bead rings,17/8 bolts, nuts, washers Two Rubber bellows only Ply Bellows Rolled Plate Assembly, 1/2 blind nuts, 3/4 NPT Style 121 Do not use Airstroke in shaded area without consulting Firestone 16 WO1-358-7272 Force to collapse to minimum height (@ 0 PSIG)....... 20 lbs. 20.3 MAX O.D. AT 100 PSIG HEIGHT 30 14 VOLUME (WITHOUT BUMPER) CU IN. x 100 16.50 BOLT CIRCLE DIA. 120 Psig 15 Assembly weight ........
126 Description RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.0 INCHES Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers Two Rolled Plate Assembly, Ply Bellows 1/2 blind nuts, 3/4 NPT Style 126 WO1-358-7727 17 WO1-358-7726 16 Static Data 8701 Do not use Airstroke in shaded area without consulting Firestone 100 Psig Assembly weight ...................................................... 21.3 lbs. 15 Force to collapse to minimum height (@ 0 PSIG)....... 25 lbs.
138-1.5 Description RECOMMENDED AIRMOUNT DESIGN HEIGHT 6.0 INCHES Assembly Order No. Ribbed neck aluminum Style 138-1.5 bead rings (equal spacing), 17/8 bolts, nuts, washers Two Ply Rubber bellows only High Strength Bellows WO1-358-7737 Static Data 3575 Do not use Airstroke in shaded area without consulting Firestone 65 65 120 Psig WO1-358-0147 60 60 Assembly weight ...................................................... 24.5 lbs. 32 (3/8-24) BOLTS EACH RING 28-32 FT. LBS. TORQUE 23.
148-1 Style 148-1 High Strength Bellows RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.5 INCHES Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers WO1-358-9601 Static Data 8411 125 Do not use Airstroke in shaded area without consulting Firestone 60 120 55 Force to collapse to minimum height (@ 0 PSIG)..... 310 lbs. 28-32 FT. LBS. TORQUE 32.68 BOLT CIRCLE DIA. 37.4 MAX O.D. AT 100 PSIG 110 Volume 100 Psig VOLUME (WITHOUT BUMPER) CU IN.
25 Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-7025 WO1-358-7047 WO1-358-7035 Two Blind nuts, 1/4 NPT both ends Ply 3/4 NPT both ends Bellows (no blind nuts) Socket head aluminum bead rings (bolts, nuts, washers not included, use cap screws) 3/4 NPT (only) upper plate, blind nuts lower plate Rubber bellows only (no girdle hoop) Static Data 8828 22 11 21 Do not use Airstroke in shaded area without consulting Firestone WO1-606-7025 10 120 Psig 20 19 WO1-358-0030 WO1-358-7030 WO1-358-0025 Assem
255-1.5 Assembly Order No. Style Blind nuts, 1/4 NPT 255-1.5 Blind nuts, 3/4 NPT Two Rubber bellows only Ply Bellows RECOMMENDED AIRMOUNT DESIGN HEIGHT 6.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT WO1-358-6955 WO1-358-6956 WO1-358-0048 Static Data B4652 Do not use Airstroke in shaded area without consulting Firestone 14 120 Psig Volume 100 Psig Assembly weight ........................................................ 3.9 lbs. Force to collapse to minimum height (@ 0 PSIG)....... 50 lbs.
224 Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-3400 WO1-358-3403 RECOMMENDED AIRMOUNT DESIGN HEIGHT 6.5 INCHES Do not use Airstroke in shaded area without consulting Firestone Assembly weight ........................................................ 5.0 lbs. Force to collapse to minimum height (@ 0 PSIG)....... 14 lbs. 2.75 8.0 MAX O.D. AT 100 PSIG HEIGHT 120 Psig Volume 100 Psig VOLUME (WITHOUT BUMPER) CU IN. x 100 15-20 FT. LBS.
26 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT Two Button head steel bead rings, Ply 17/8 bolts, nuts, washers Bellows Rubber bellows only WO1-358-7325 WO1-358-7327 Style 26 RECOMMENDED AIRMOUNT DESIGN HEIGHT 8.0 INCHES Static Data 8442 4 WO1-358-7333 WO1-358-0142 Do not use Airstroke in shaded area without consulting Firestone Assembly weight ........................................................ 5.3 lbs. 100 Psig 15-20 FT. LBS. TORQUE 1/4 NPT AIR INLET 2.75 8.
20 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Countersunk steel bead rings, 13/4 bolts, nuts, washers Rubber bellows only WO1-358-6910 WO1-358-6911 WO1-358-6900 WO1-358-6901 Style 20 RECOMMENDED AIRMOUNT DESIGN HEIGHT 8.
20-2 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT Two Blind nuts, 3/4 NPT, Ply rubber bumper Bellows Rubber bellows only Style 20-2 RECOMMENDED AIRMOUNT DESIGN HEIGHT 10.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT WO1-358-6951 WO1-358-6952 WO1-358-6947 WO1-358-0152 Static Data A9902 Do not use Airstroke in shaded area without consulting Firestone 60 60 120 Psig Assembly weight ........................................................ 7.7 lbs.
22 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Countersunk steel bead rings, 15/8 bolts, nuts, washers Rubber bellows only WO1-358-7180 WO1-358-7400 WO1-358-7184 WO1-358-7185 Style 22 RECOMMENDED AIRMOUNT DESIGN HEIGHT 9.
22-1.5 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, rubber bumper Two Ply Blind nuts, 3/4 NPT Bellows Blind nuts, 1/4 NPT(centered) Rubber bellows only WO1-358-7444 Style 22-1.5 RECOMMENDED AIRMOUNT DESIGN HEIGHT 10.5 INCHES WO1-358-7473 WO1-358-7442 WO1-358-7443 WO1-358-0259 Static Data 1889 12 12 Do not use Airstroke in shaded area without consulting Firestone 11 Assembly weight ...................................................... 12.9 lbs.
21 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Button head steel bead rings, 17/8 bolts, nuts, washers Rubber bellows only WO1-358-7145 WO1-358-7146 WO1-358-7143 WO1-358-7144 Style 21 RECOMMENDED AIRMOUNT DESIGN HEIGHT 9.
21-2 Style 21-2 Two Ply Bellows RECOMMENDED AIRMOUNT DESIGN HEIGHT 10.5 INCHES Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, rubber bumper Blind nuts, 3/4 NPT WO1-358-6800 WO1-358-6801 WO1-358-9529 Static Data 3931 Do not use Airstroke in shaded area without consulting Firestone 18 18 17 16 1/4 OR 3/4 NPT AIR INLET 6.25 15-20 FT. LBS. TORQUE 6.25 16.0 MAX O.D. AT 100 PSIG OPTIONAL BUMPER HEIGHT VOLUME (WITHOUT BUMPER) CU IN. x 100 Force to collapse to minimum height (@ 0 PSIG).
233-2 Two Ply Bellows Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, rubber bumper Blind nuts, 3/4 NPT WO1-358-6810 RECOMMENDED AIRMOUNT DESIGN HEIGHT 11.25 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data A9899 20 20 Do not use Airstroke in shaded area without consulting Firestone WO1-358-7781 WO1-358-6811 18 18 120 Psig Assembly weight ....................................................... 19.6 lbs Force to collapse to minimum height (@ 0 PSIG)..... 100 lbs.
28 RECOMMENDED AIRMOUNT DESIGN HEIGHT 9.5 INCHES Assembly Order No. WO1-358-7191 24 WO1-358-7192 23 25 22 WO1-358-7271 WO1-358-7925 Assembly weight ....................................................... 19.0 lbs Force to collapse to minimum height (@ 0 PSIG)....... 38 lbs.
203 RECOMMENDED AIRMOUNT DESIGN HEIGHT 9.5 INCHES Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers Two Ribbed neck aluminum bead Ply rings (equal spacing) 11/4 b,n,w Bellows Rolled plate assembly, 1/2 blind but 3/4 NPT Rubber bellows only Style 203 WO1-358-7227 WO1-358-7225 WO1-358-7273 WO1-358-0205 Force to collapse to minimum height (@ 0 PSIG)....... 40 lbs.
29 RECOMMENDED AIRMOUNT DESIGN HEIGHT 9.5 INCHES Assembly Order No. WO1-358-7203 40 WO1-358-7201 Assembly weight ....................................................... 28.8 lbs Force to collapse to minimum height (@ 0 PSIG)....... 70 lbs.
200 RECOMMENDED AIRMOUNT DESIGN HEIGHT 9.5 INCHES Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers Two Ribbed neck aluminum bead Ply rings (equal spacing) 11/4 b,n,w Bellows Rubber bellows only Style 200 WO1-358-7772 WO1-358-7775 WO1-358-5126 Static Data 5536 Do not use Airstroke in shaded area without consulting Firestone 55 55 Assembly weight ....................................................... 34.9 lbs VOLUME (WITHOUT BUMPER) CU IN.
215 RECOMMENDED AIRMOUNT DESIGN HEIGHT 10.5 INCHES Assembly Order No. 3560 Do not use Airstroke in shaded area without consulting Firestone 65 65 WO1-358-7230 Assembly weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 38.4 lbs. Force to collapse to minimum height (@ 0 PSIG)..... 160 lbs. 32 (3/8-24) BOLTS EACH RING 28-32 FT. LBS. TORQUE 23.50 BOLT CIRCLE DIA. 27.9 MAX O.D.
248-2 Description Style 248-2 Four Ply Bellows RECOMMENDED AIRMOUNT DESIGN HEIGHT 11.0 INCHES Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers WO1-358-9602 Static Data B412 125 Do not use Airstroke in shaded area without consulting Firestone Assembly weight ...................................................... 72.5 lbs. 120 Force to collapse to minimum height (@ 0 PSIG)..... 350 lbs.
352 Style 352 Description Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT WO1-358-8048 WO1-358-8047 RECOMMENDED AIRMOUNT DESIGN HEIGHT 13.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data B4789 16 16 Do not use Airstroke in shaded area without consulting Firestone Two Ply Bellows 14 14 Assembly weight ...................................................... 20.3 lbs. 1/4 OR 3/4 NPT AIR INLET 2.88 15-20 FT. LBS. TORQUE 6.20 13.1 MAX O.D.
313 Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 1/4 NPT, bumper Blind nuts, 3/4 NPT Two Blind nuts, 3/4 NPT, bumper Ply Bellows Button head steel bead rings, 17/8 bolts, nuts, washers Rubber bellows only Style 313 CONSULT FIRESTONE BEFORE USING AS AIRMOUNT WO1-358-7808 WO1-358-7811 WO1-358-7802 WO1-358-7807 WO1-358-1098 WO1-358-7815 WO1-358-1099 3/8-16 BLIND NUTS (5/8 DEEP) 1/4 OR 3/4 NPT AIR INLET 6.25 15-20 FT. LBS. TORQUE 6.25 15.1 MAX O.D.
333 Assembly Order No. Blind nuts, 1/4 NPT Blind nuts, 3/4 NPT Two Blind nuts, 1/4 NPT, bumper Ply Button head steel bead ring Bellows 17/8 bolts, nuts, washers Rubber bellows only WO1-358-7845 WO1-358-7842 WO1-358-7838 Style 333 RECOMMENDED AIRMOUNT DESIGN HEIGHT 14.7 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data 8695 22 22 Do not use Airstroke in shaded area without consulting Firestone 20 WO1-358-7830 WO1-358-7019 20 Volume 100 Psig Assembly weight ...........................
312 Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers Two Ribbed neck aluminum bead Ply rings (unequal spacing) 17/8 b,n,w Bellows Rolled plate assembly, 1/2 blind nuts, 3/4 NPT Rubber bellows only Style 312 WO1-358-7761 WO1-358-7760 WO1-358-7286 WO1-358-7914 CONSULT FIRESTONE BEFORE USING AS AIRMOUNT 26 Volume 100 Psig 24 23 21 VOLUME (WITHOUT BUMPER) CU IN.
323 Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers Two Rolled plate assembly, 1/2 Ply blind nuts, 3/4 NPT Bellows Rubber bellows only Style 323 CONSULT FIRESTONE BEFORE USING AS AIRMOUNT RECOMMENDED AIRMOUNT DESIGN HEIGHT 13.0 INCHES Static Data 1808 WO1-358-7823 WO1-358-7274 WO1-358-7921 70 35 Assembly weight ....................................................... 31.
320 Description Assembly Order No. Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers Two Rolled plate assembly, 1/2 Ply blind nuts, 3/4 NPT Bellows Rubber bellows only Style 320 CONSULT FIRESTONE BEFORE USING AS AIRMOUNT RECOMMENDED AIRMOUNT DESIGN HEIGHT 14.0 INCHES Static Data 5282 WO1-358-7324 Do not use Airstroke in shaded area without consulting Firestone 90 WO1-358-7276 WO1-358-0987 45 120 Psig Assembly weight .......................................................
321 Description Assembly Order No. RECOMMENDED AIRMOUNT DESIGN HEIGHT 15.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Style 321 Ribbed neck aluminum bead rings (equal spacing), 7 WO1-358-7304 Two Ply 1 /8 bolts, nuts, washers Ribbed neck aluminum bead High 7 Strength rings (unequal spacing) 1 /8 b,n,w WO1-358-7306 WO1-358-7919 Bellows Rubber bellows only Static Data 1229 120 Psig Do not use Airstroke in shaded area without consulting Firestone 130 65 120 60 Assembly weight ..............
348-3 Assembly Order No. RECOMMENDED AIRMOUNT DESIGN HEIGHT 15.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Style 348-3 Ribbed neck aluminum bead rings (equal spacing), 17/8 bolts, nuts, washers High Strength Rubber bellows only Bellows WO1-358-9603 WO1-358-1023 25 23 Force to collapse to minimum height (@ 0 PSIG)..... 380 lbs. 22 8413 125 Do not use Airstroke in shaded area without consulting Firestone 24 Assembly weight ..................................................... 103.
1X84D-1 RECOMMENDED AIRMOUNT DESIGN HEIGHT 8.0 INCHES AIRMOUNT ISOLATOR ONLY Description Assembly Order No. Style Thin wall assembly, 1X84D-1 without cap Thin wall Thin wall assembly, Two Ply with cap (dotted line) Bellows Thin wall rubber bellows only Static Data R9260 WO1-358-9188 11 11 10 10 WO1-358-9190 WO1-358-0480 5.25 BOLT CIRCLE DIA. 5.60 USE 1/4" CAP SCREWS (INCLUDED WITH CAP ASSEMBLY ONLY) 4.75 (OPTIONAL CAP) “O” RING (IS INCLUDED) 4.12 4.38 1/4 NPT AIR INLET 25-30 FT. LBS.
4001 Style 4001 Description Assembly Order No. Blind nut, 1/8 NPT WO2-358-4001 RECOMMENDED AIRMOUNT DESIGN HEIGHT 5.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Two Ply Bellows Static Data 8611 Do not use Airstroke in shaded area without consulting Firestone Assembly weight ........................................................ 1.0 lbs. 4 1/8 NPT AIR INLET 3.1 MAX O.D. AT 80 PSIG 1.65 DIA. .50 15-20 FT. LBS.
7002 Style 7002 Description Assembly Order No. Blind nut, 1/8 NPT WO2-358-7002 RECOMMENDED AIRMOUNT DESIGN HEIGHT 4.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data 8609 120 Psig Two Ply Bellows Do not use Airstroke in shaded area without consulting Firestone 11 Assembly weight ........................................................ 1.8 lbs. 15-20 FT. LBS. TORQUE 4.2 MAX O.D. AT 80 PSIG 2.83 DIA.
7010 Style 7010 Description Assembly Order No. Blind nut, 1/8 NPT WO2-358-7010 RECOMMENDED AIRMOUNT DESIGN HEIGHT 8.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Two Ply Bellows Static Data 8612 Do not use Airstroke in shaded area without consulting Firestone 9 9 Assembly weight ........................................................ 1.6 lbs. Volume 80 Psig 1/8 NPT AIR INLET 12-18 FT. LBS. TORQUE 4.0 MAX O.D. AT 80 PSIG 25-30 FT. LBS. TORQUE 2.76 DIA. 3/4-16 .
7012 Style 7012 Description Assembly Order No. Blind nut, 1/8 NPT WO2-358-7012 RECOMMENDED AIRMOUNT DESIGN HEIGHT 8.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Two Ply Bellows Static Data 8108 Volume 80 Psig 10 10 100 Psig Assembly weight ........................................................ 1.8 lbs. 1/8 NPT AIR INLET 12-18 FT. LBS. TORQUE 25-30 FT. LBS. TORQUE 5.0 MAX O.D. AT 80 PSIG 2.76 DIA. .
1T12E-3 Assembly Order No. RECOMMENDED AIRMOUNT DESIGN HEIGHT 10.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT WO1-358-8119 Style Blind nuts, 1/4 NPT 1T12E-3 Socket head aluminum bead ring (bolts, nuts, washers not Two included, use cap screws) WO1-358-8118 Ply Bellows Static Data 9232 Do not use Airstroke in shaded area without consulting Firestone 15 15 14 Assembly weight ........................................................ 3.5 lbs.
1T14C-1 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T14C-1 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Countersunk steel bead ring 13/4 bolts, nuts, washers WO1-358-5310 WO1-358-5311 WO1-358-5305 WO1-358-5306 RECOMMENDED AIRMOUNT DESIGN HEIGHT 10.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data 3019 Do not use Airstroke in shaded area without consulting Firestone WO1-358-5307 Assembly weight ...............................
1T14C-3 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T14C-3 RECOMMENDED AIRMOUNT DESIGN HEIGHT 11.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT WO1-358-5405 Static Data 3018 Volume 100 Psig Two Ply Bellows Assembly weight ........................................................ 6.8 lbs. 120 Psig 1/4 OR 3/4 NPT AIR INLET 1.75* 15-20 FT. LBS. TORQUE *(1.50 FOR 3/4) 3.50 9.1 MAX O.D. AT 100 PSIG 6.31 DIA. HEIGHT 25-30 FT. LBS.
1T14C-7 Assembly Order No. Style Blind nuts, 1/4 NPT 1T14C-7 Blind nuts, 3/4 NPT Two Ply Bellows WO1-358-5712 WO1-358-5708 WO1-358-5743 120 Psig 15-20 FT. LBS. TORQUE *(1.50 FOR 3/4) 3.50 9.1 MAX O.D. AT 100 PSIG 6.31 DIA. HEIGHT VOLUME (WITHOUT BUMPER) CU IN. x 100 1/4 OR 3/4 NPT AIR INLET 1.75* 4 100 Psig Volume 100 Psig 6 3 80 Psig 60 Psig 4 2 40 Psig 2 1 20 Psig 25-30 FT. LBS. TORQUE 3.16 1/2-13 THREADED HOLE (3/4 DEEP) 7.25 DIA.
1T15T-1 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T15T-1 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Bellows WO1-358-9400 WO1-358-9402 WO1-358-9401 RECOMMENDED AIRMOUNT DESIGN HEIGHT 7.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data 4209 Do not use Airstroke in shaded area without consulting Firestone 8 8 Assembly weight ...................................................... 10.4 lbs. 1/4 OR 3/4 NPT AIR INLET 15-20 FT. LBS. TORQUE 2.88 6.20 11.
1T15S-6 Assembly Order No. Style Blind nuts, 1/4 NPT 1T15S-6 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Bellows WO1-358-9048 WO1-358-9049 WO1-358-9051 15-20 FT. LBS. TORQUE 2.88 6.20 11.1 MAX O.D. AT 100 PSIG 9.00 DIA. HEIGHT 25-30 FT. LBS. TORQUE OPTIONAL BUMPER VOLUME (WITHOUT BUMPER) CU IN. x 100 1/4 OR 3/4 NPT AIR INLET Static Data 7597 Volume 100 Psig 8 Assembly weight .......................................................13.7 lbs.
1T15L-4 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T15L-4 RECOMMENDED AIRMOUNT DESIGN HEIGHT 11.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT WO1-358-9414 Two Ply Bellows Static Data 3105 Do not use Airstroke in shaded area without consulting Firestone 18 9 Assembly weight ...................................................... 15.5 lbs. 120 Psig 1/4 OR 3/4 NPT AIR INLET 15-20 FT. LBS. TORQUE 2.88 6.20 11.7 MAX O.D. AT 100 PSIG 9.00 DIA. OPTIONAL BUMPER 25-30 FT. LBS.
1T15M-0 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T15M-0 Blind nuts, 1/4 NPT, rubber bumper Two Ply Blind nuts, 3/4 NPT Bellows Blind nuts, 3/4 NPT, rubber bumper Countersunk steel bead ring, 13/8 bolts, nuts, washers Integral studs, 1/4 NPT WO1-358-9030 WO1-358-9031 WO1-358-9034 8826 120 Psig 9 WO1-358-9036 2.88 15-20 FT. LBS. TORQUE 6.20 12.8 MAX O.D. AT 100 PSIG 9.00 DIA.
1T15M-2 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T15M-2 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows WO1-358-9042 WO1-358-9053 WO1-358-9054 WO1-358-9099 RECOMMENDED AIRMOUNT DESIGN HEIGHT 9.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data A9109 Do not use Airstroke in shaded area without consulting Firestone 10 10 120 Psig Assembly weight ...................................................... 13.2 lbs.
1T15M-4 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T15M-4 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows WO1-358-9056 WO1-358-9057 WO1-358-9062 WO1-358-9060 RECOMMENDED AIRMOUNT DESIGN HEIGHT 12.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data 3068 Do not use Airstroke in shaded area without consulting Firestone 20 10 120 Psig Assembly weight ....................................................... 14.
1T15M-6 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T15M-6 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Blind nuts, 3/4 NPT (piston not included) WO1-358-9079 WO1-358-9096 WO1-358-9089 WO1-358-9088 RECOMMENDED AIRMOUNT DESIGN HEIGHT 15.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data 4452 Do not use Airstroke in shaded area without consulting Firestone 20 10 120 Psig WO1-358-0730 1/4 OR 3/4 NPT AIR INLET 2.88 15-20 FT.
1T15M-9 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T15M-9 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows WO1-358-9108 WO1-358-9104 WO1-358-9106 WO1-358-9117 RECOMMENDED AIRMOUNT DESIGN HEIGHT 18.5 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data 3797 Do not use Airstroke in shaded area without consulting Firestone 20 10 120 Psig Assembly weight ...................................................... 18.0 lbs.
1T19L-7 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T19L-7 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Button head steel bead ring 17/8 bolts, nuts, washers WO1-358-9148 WO1-358-9149 WO1-358-9172 WO1-358-9160 RECOMMENDED AIRMOUNT DESIGN HEIGHT 15.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data B0308 16 32 Do not use Airstroke in shaded area without consulting Firestone 14 28 WO1-358-9165 1/4 NPT AIR INLET 6.25 3.
1T19L-11 Description Assembly Order No. Style Blind nuts, 1/4 NPT 1T19L-11 Blind nuts, 1/4 NPT, bumper Two Blind nuts, 3/4 NPT Ply Blind nuts, 3/4 NPT, bumper Bellows Button head steel bead ring 17/8 bolts, nuts, washers WO1-358-9155 WO1-358-9156 WO1-358-9153 WO1-358-2132 RECOMMENDED AIRMOUNT DESIGN HEIGHT 18.0 INCHES CONSULT FIRESTONE BEFORE USING AS AIRMOUNT Static Data B0307 16 32 Do not use Airstroke in shaded area without consulting Firestone WO1-358-9162 28 14 24 12 1/4 NPT AIR INLET 6.
INDEX STYLE NUMBER TO PAGE NUMBER TWO PLY STYLE NO. HIGH STRENGTH STYLE NO. SEE PAGE SINGLE CONVOLUTION TWO PLY STYLE NO. HIGH STRENGTH STYLE NO. SEE PAGE TRIPLE CONVOLUTION 16 38 352 16-ST 39 313 131 40 333 110 41 312 314 75 42 323 324 76 43 320 328 77 44 321 45 348-3 116 117 116-1 115 124 19 19-.75 128 47 113-1 128-1 48 153-2 49 119 50 121 51 126 52 138-1.5 53 [148-1 is high strength] 54 DOUBLE CONVOLUTION 55 255-1.
® AIRSTROKE ACTUATOR DESIGN PARAMETER WORKSHEET 1. FORCE REQUIRED: 6. ENVIRONMENTAL CONDITIONS: 2. STROKE REQUIRED: 7. CYCLE RATE: 3. AVAILABLE AIR PRESSURE: 8. RESPONSE TIME REQUIRED: 4. ANGLE OF MOTION (PLEASE SKETCH): SPECIAL REQUIREMENTS: 5.
® AIRMOUNT ISOLATOR DESIGN PARAMETER WORKSHEET FOR VIBRATION ISOLATION FOR ISOLATING AN UNBALANCED MASS A) TO PREVENT OUTGOING VIBRATION TRANSMISSION (INTO THE SURROUNDING AREA), OR 13. PLEASE COMPLETE 1 THROUGH 12, AND ALSO INCLUDE: B) FOR ISOLATING DELICATE EQUIPMENT FROM INCOMING VIBRATIONS, PLEASE COMPLETE THE FOLLOWING: 14. TYPE OF MOVING COMPONENTS (UNBALANCED MASS): 1. DESCRIPTION OF EQUIPMENT: 15. WEIGHT OF UNBALANCED MOVING MASS (lbs.): 16. RADIUS OF MOVEMENT (inches): 17.
® Airstroke actuators/Airmount isolators Printed in U.S.A. EMDG 198 EMDG 198 12650 Hamilton Crossing Blvd. Carmel, Indiana 46032 1-800-888-0650 support@firestoneindustrial.