Brochure

FIREYE PRIMELINE PRODUCTS • 55
“M” Series Controls
UVM, TFM Controls have their date code stamped
on the side of the chassis.
M-II Series and MicroM Series Controls
Both the M-II and MicroM Series Controls have the
model number printed on a label located on the
chassis, amplifier and programmer. The date code,
serial number and engineering codes are printed
on a label on the chassis. The date code and engi-
neering code are stamped on the underside of the
printed circuit board on the programmer and ampli-
fiers.
“D” Series Controls
D-Series Chassis Controls (70D10/, 70D20/21,
70D30 & 70D40/41) have date code, engineering
code, and model number stamped on the control.
Model number appears on chassis board under top
end of the chassis and on a label on the black plas-
tic rear cover of the chassis. D-Series Amplifiers
and Programmers have their model numbers in the
lower right hand corner as you look at the covered
side. Their date code is just opposite the model
number but on the uncovered side of the circuit
board.
Flame-Monitor Controls
Flame-Monitor Chassis (EB700, EB720, EB721)
have the model number, date code, and engineer-
ing code stamped on the bottom of the chassis.
Flame-Monitor Amplifiers and programmers have
their model number printed on a label located on
the upper left hand corner tab. Their date code and
engineering code appear on the uncovered side of
the printed circuit board.
BurnerLogiX Controls
BurnerLogiX Chassis' (YB, ZB) and Interlock
Annunciators (YZ), have their model number, date
code, and engineering code printed on a label
located on the left side of the product. The Burner-
LogiX Programmer Modules (YP) have the date
code ink-stamped on the top surface of the prod-
uct. The BurnerLogiX Display Modules (BLL, BLV)
have the date code ink-stamped on their pc boards,
next to the RJ45 ribbon cable connector.
“C” Series Controls
Types 24CJ5, 25CU6, 25DU4, 26CF6 have chassis
labels located on the top of the amplifier that identify
the control as to type and model. The code and serial
numbers appear stamped on left side of control and
stamped on front of the control just above or below
the timer motor. The serial number for “C” Series
controls is coded as follows: “72B” indicates February
1972 unit, “71D” indicates April 1971 unit.
PPC4000 Controls
PPC4000 Control has a barcode label located on the
top of its cover that contains the model number, date
code, engineering code, and serial number. The date
code is the first four digits of the six-digit group. In the
following example, the date code is 1135: 01-
PPC4000-113504-0171.
Factory Trade-In
The following Fireye control models are acceptable
as trade-in toward the purchase of any applicable Fir-
eye control at trade-in pricing from an Authorized
Primeline Distributor. (Refer to the current price sheet
CG-14 for part numbers with trade-in pricing):
C-Series, P-Series, M-Series, M-Series II (Chassis
and Programmers only), D-Series (Chassis, Program-
mer, Amplifier), Flame-Monitor (Chassis,
Programmer, Amplifier), an BurnerLogiX. Used Hon-
eywell controls are also accepted towards trade-in
purchase of Fireye controls.
The only requirement is that the Honeywell control be
of the same type functionally as the desired new Fir-
eye control. Check with your local Fireye sales office
for further details.
IMPORTANT NOTICE
When replacing Honeywell controls with Fireye con-
trols, be sure to follow the wiring diagram included
with the Fireye unit. Fireye and Honeywell controls
are not directly interchangeable, external wiring
requirements are different.
HOW TO IDENTIFY FIREYE CONTROLS
Beginning January 1976 Fireye adopted the US national standard date coding for all units whereby
the first two digits identify the year and the second two digits identify the week of the year. Example
9212—twelfth week of 1992.