Product Overview

ManualsBrandsFireye ManualsHeating Supplies0.8 Sec. FFRT MicroM Infrared Amplifier

Table Of Contents

DESCRIPTION

The Fireye MEUV1, MEUV4, MEUVS1, MEUVS4, MERT1, MERT4, MEIR1, MEIR4, MECD1

and MECD4 are Ampliﬁer Modules used with the Fireye Modular MicroM control. These ampliﬁer

modules provide ﬂame scanning capabilities using any of the Fireye standard ultraviolet scanners,

self-check scanners, infrared scanners, cadmium sulﬁde scanners, ﬂame rods, and photocells. The

Flame Failure Response Time (F.F.R.T.) of the control is determined by the selection of the ampliﬁer

module (see Ordering Information). Test jacks are provided on the ampliﬁer modules to permit ﬂame

signal measurement during operation and is a uniform 0-10 vdc for all models.

After scanner selection, the proper ampliﬁer module

must

be used in the Modular MicroM chassis

(see Ordering Information). The ampliﬁer module incorporates a plug-in design for ease of installa-

tion.

The programmer module determines the operational characteristics of the control (e.g. relight, purge

timing, etc.).

For proper and safe application of this product, you must refer to bulletin MC-5000 for a detailed

description of the operation of the Modular MicroM control, including installation instructions,

operating sequences for the programmer modules, etc. Also follow the scanner installation and wir-

ing instructions found in bulletins MC-5000 for proper ﬂame scanning operation.

WARNING: Selection of this control for a particular application should be made by a com-

petent professional, licensed by a state or other government agency. Inappropriate application

of this product could result in an unsafe condition hazardous to life and property. Installation

should not be considered complete until pilot turndown and other appropriate performance

tests have been successfully completed.

MEUV1, MEUV4,MEUVS1,

MEUVS4,MEIR1,MEIR4,

MERT1,MERT4,

MECD1 and MECD4

AMPLIFIER MODULES FOR USE WITH THE

FIREYE

MODULAR MicroM™ CONTROL

MAMP-1

JANUARY 2000

Year 2000 Compliant in accordance with BSI document DISC PD2000-I:1998



APPROVED

LISTED



Summary of content (4 pages)

PAGE 1
® MAMP-1 JANUARY 2000 MEUV1, MEUV4,MEUVS1, MEUVS4,MEIR1,MEIR4, MERT1,MERT4, MECD1 and MECD4 AMPLIFIER MODULES FOR USE WITH THE FIREYE® MODULAR MicroM™ CONTROL C UL  LISTED  US APPROVED Year 2000 Compliant in accordance with BSI document DISC PD2000-I:1998 DESCRIPTION The Fireye MEUV1, MEUV4, MEUVS1, MEUVS4, MERT1, MERT4, MEIR1, MEIR4, MECD1 and MECD4 are Amplifier Modules used with the Fireye Modular MicroM control.
PAGE 2
 ORDERING INFORMATION Flame Amplifier Selection: MicroM Amplifier Models: MEUV1 MEUV4 MEUVS1 MEUVS4 MERT1 MERT4 MEIR1 MEIR4 MECD1 MECD4 UV amplifier,0.8 second FFRT, uses UV1A, UV2, UV8A and 45UV3-1050 scanners. UV amplifier, 3 second FFRT, uses UV1A, UV2, UV8A and 45UV3-1050 scanners. UV Self-Check amplifier,0.8 second FFRT, uses 45UV5-1009 scanner. UV Self-Check amplifier, 3 second FFRT, uses 45UV5-1009 scanner. Flame Rod / Photocell amplifier,0.8 second FFRT, uses 69ND1 or 45CM1.
PAGE 3
® BULLETIN INFRARED SCANNERS: 48PT2-1003 48PT2-1007 48PT2-9003 48PT2-9007 48PT2-9007W Infrared scanner 8 ft. (2400mm) shielded cable, straight head. Infrared scanner 4 ft. (1200mm) shielded cable, straight head. Infrared scanner 8 ft. (2400mm) shielded cable, 90° head. Infrared scanner 4 ft. (1200mm) shielded cable, 90° head. Infrared scanner 4 ft. (1200mm) shielded cable, 90° head, water repellent.
PAGE 4
 INSTALLATION The amplifier modules are used with the Fireye Modular MicroM Base Chassis (P/N MEC120, MEC120C, MEC120R, MEC120D, MEC120RC for 120VAC, P/N MEC230, for 230VAC). They are installed in the chassis by grabbing hold of the amplifier module by the edges of its printed circuit board, aligning the module with the guide slots on the opening in the middle of the chassis, and inserting the module into the pin connectors. The amplifier modules are designed to fit in the proper slot only.