F IC LM13W User Guide 1
N otebook User Guide Copyright©2005 All Rights Reserved - Printed in Taiwan Notebook Computer User Guide Original Issue: 2005/6 This manual guides you in setting up and using your new notebook computer. Information in this manual has been carefully checked for accuracy and is subject to change without notice.
N otebook User Guide F CC Information to User Safety and Care Instructions No matter what your level of experience with computers, please make sure you read the safety and care instructions. This information can help protect you and your computer from possible harm. Radio and television interference Warning: Use the specified shielded power cord and shielded signal cables with this computer, so as not to interfere with radio and television reception.
N otebook User Guide You may find helpful the following booklet, prepared by the Federal Communications Commission: Interference Handbook (stock number 004000-00345-4). This booklet is available from the U.S. Government Printing Office, Washington, DC20402 Warning: The user must not modify or change this computer without approval. Modification could void authority to this equipment.
N otebook User Guide Only peripherals (input/output devices, terminals, printers, etc) certified to comply with Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Optical Disk Drive Notice The optical disk drive is Class 1 Laser Product.
N otebook User Guide 99/5/E C and 89/3360E E C. The equipment was passed. The test was performed according to the following E uropean standards: E N 300 328-2 V.1.2.1 (2001-12) E N 301 489-1 V.1.3.1 (2001-09) / E N 301 489-17 V.1.1.1 (2000-09) E N 50371: 2002 E N 55022: 2001 E N 55024: 2001 E N 60950: 2000 E N 61000-3-2: 2000 E N 61000-3-3: 1995 + A1: 2001 802.11b Restrictions: - E uropean standards dictate maximum radiated transmit power of 100mW E IRP and frequency range 2.400-2.
N otebook User Guide F or DVD Players with both 525p and 625p progressive scan outputs: ‘CONSUME RS SHOULD NOTE THAT NOT ALL HIGH DE FINITION TE LE VISION SE TS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYE D IN THE PICTURE . IN CASE OF 525 OR 625 PROGRE SSIVE SCAN PICTURE PROBLE MS, IT IS RE COMME NDE D THAT THE USE R SWITCH THE CONNE CTION TO THE ‘STANDARD DE FINITION’ OUTPUT.
N otebook User Guide About Your Notebook Computer Congratulation for having purchased your new Professional Multimedia Notebook. This notebook incorporates the strongest features, which integrate the latest technologies available in the notebook industry. Your new notebook computer not only drives today multimedia applications but also be ready for tomorrow exciting new software.
N otebook User Guide About Your User Guide Welcome to your Professional Multimedia Notebook User Guide. This manual covers everything you need to know in learning how to use your computer. This manual also assumes that you know the basic concepts of Windows and the PC. You will start doing a lot of great and fun things with your computer. This manual is divided into eight chapters. Chapter 1 gives introduction on your computer features.
N otebook User Guide Table of Contents ABOUT YOUR NOTEBOOK COMPUTER.......................................... 8 ABOUT YOUR USER GUIDE................................................................. 9 1 INTRODUCTION............................................................................. 15 1.1 1.2 1.3 FEATURE HIGHLIGHT .................................................................... 16 UNPACKING THE COMPUTER .........................................................
N 2.6 3 otebook User Guide Installing the VGA Device Driver ................................................ 43 Installing the Control Panel of vga utility.................................... 43 Installing the Audio Device Driver............................................... 44 Installing the Modem Device Driver ............................................ 44 Installing ENE - Keyboard Controller driver .............................. 45 Installing ALPS - Touch Pad driver .................................
N otebook User Guide 3.9 4 FUN WITH MULTIMEDIA .................................................................. 73 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 5 Making PC Cards Work ............................................................... 68 Hot Swapping PC Cards .............................................................. 69 USING FLASH MEMORY CARDS ..................................................... 69 What is Flash Memory Card? ......................................................
N 6.3 6.4 6.5 6.6 6.7 7 otebook User Guide 6.2.1 Internal HDD Sub-Menu................................................. 100 6.2.2 Internal Optical Drive Sub-Menu .................................... 101 USING THE ADVANCED CMOS SETUP ......................................... 102 SECURITY MENU SETUP .............................................................. 104 USING THE BOOT SETUP .............................................................. 106 HOW TO EXIT THE SETUP PROGRAM ..........................
N otebook User Guide Glide Pad.................................................................................... 127 Keyboard .................................................................................... 128 Flash BIOS ................................................................................. 128 I/O Ports ..................................................................................... 128 Wireless devices .........................................................................
1 Introduction 1 Introduction Y our Notebook PC is a fully Windows compatible portable personal computer. With the latest features in mobile computing and multimedia technology, this notebook makes a natural traveling companion. With leap of technology and compact, your Notebook PC runs on a whole wide range of general business, personal productivity, entertainment, and professional applications. It is ideal for use in the office, at home, and on the road.
N otebook User Guide 1.1 Feature Highlight Before we go to identify each part of your Notebook PC, we will first introduce you to other notable features of your computer. Processing Unit • Your notebook runs on Intel® Celeron® M Dothan microprocessor that is integrated with 1MB L2 Cache. Check with your dealer on the CPU type and speed. • Fully compatible with an entire library of PC software based on operating systems such as Windows XP.
1 Introduction IE E E 1394 Provides one IE E E 1394 port for fast data transmission by external hard disk or digital video (DV). USB 2.0 Provides four USB2.0 ports for fastest I/O data transmission. Graphic System Provides blazing graphics controller embedded in ATI RC410MB chipset PCMCIA Provides one PCMCIA slot that allows you to insert one Type II card. PCI Local Bus Architecture • 32-bit PCI E nhanced IDE optimizes the data transfer between the CPU and PATA hard disk drives.
N otebook User Guide Power and System Management • Integrated SMM (System Management Mode) on system chipset that shuts down components not in use to reduce power consumption. To execute power management, you can set up the parameter in Power Options properties by pointing your mouse to Control Panel of Windows. • Closing the Notebook computer (lowering the cover) allows you to suspend the system operation instantly and resume at the press of the power button.
1 Introduction Carefully inspect each component to make sure that nothing is missing and/or damaged. If any of these items is missing or damaged, notify your dealer immediately. Be sure to save the shipping materials and the carton in case you need to ship the computer or if you plan to store the computer away sometime in the future. 1.3 The Inside of the Notebook The notebook computer is compact with features on every side. First, look at the inside of the system.
N otebook User Guide • Color Widescreen LCD Display The notebook computer comes with a color LCD that you can adjust for a comfortable viewing position. The LCD is 15.4” TFT color LVDS with 1280x800 (Wide XGA with ratio 16:10) resolution panels. The features of the Color LCD Display are summarized as follows: ⇓ TFT color LVDS with Widescreen 15.4” 1280x800 (Wide XGA) resolution panels. ⇓ Capable of displaying 16M colors (32-bit true color) on either size panels.
1 Introduction • Touchpad Pointing Device Microsoft mouse compatible with two Touchpad click buttons. The two select buttons located at each side support tapping selection and dragging functions. These buttons work like a standard computer mouse. Simply move your fingertip over the Glide Pad to control the position of the cursor. Use the selection buttons below the Glide Pad to select menu items.
N otebook User Guide 1. Power Indicator 2. Battery Charging LE D 3. Drive Access 4. Wireless LAN Access 5. Caps Lock 6. Scroll Lock 7. Num Lock • Power Indicator Lets you know that power to the system is turned on. This LE D is positioned so that you can see the power state whether the LCD panel is opened or closed. • ⇓ Lights green when the system is powered on. ⇓ Lights green blinking when the system is in Standby mode. ⇓ Lights yellow when the battery power is low.
1 Introduction • Drive Access When LE D in blue blinking light indicates that the system is accessing the Hard Disk or Optical Disk Drive. • Wireless LAN access When LE D in blue light indicates that the wireless LAN module is activated. When LE D lights off, it indicates that the function is disabled. • Caps Lock When LE D in blue light indicates that the Caps Lock key on the keyboard is activated. When activated, all alphabet keys typed in will be in uppercase or capital letters.
N otebook User Guide T HE F UNCTION OF E ASY B UTTON S 1. CPU Throttling • 2. Internet Button 3. Wireless LAN Button CPU Throttling Press this button to decrease the CPU performance speed in order to save power for extending battery life and operation time. • Internet Button This technology is designed specifically for providing a very convenient way in connecting Internet only by pressing Internet button as shown in the graphics. Just Press this button to open the Internet E xplorer directly.
1 Introduction 1.4 The Front Side of the Notebook 1. Cover Switch • Cover Switch The cover (LCD panel) is locked when it is closed. Slide the button right aside to release the latch for opening the cover of the computer. 1.5 The Rear Side of the Notebook The system ports at the back of your notebook computer can connect various devices. E ach port is described as followings. 1. USB 2.0 Ports 2. VGA Port 3.
N otebook User Guide • USB 2.0 Ports The Universal Serial Bus (USB) port allows you to connect USB 2.0compliant devices (for example, printers, scanners and so on) to your notebook computer. • VGA Port Lets you attach an external monitor or projector for wider display. You can run the LCD display and the external monitor simultaneously or switch it to monitor only using the display hot-key.
1 Introduction 1.6 The Left Side of the Notebook The left side of your notebook computer provides the features shown in the following figure. 1. DC Power Port 3. Optical Disk Drive 5. Headphone Jack • 2. Modem Port 4. USB 2.0 Ports 6. Microphone Jack DC Power Port Lets you connect the AC power adapter in supplying continuous power to your notebook and recharging the battery. • Modem Port A 56K internal fax/data modem is installed. It keeps you connected to the outside world through phone line.
N otebook User Guide When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3.
1 Introduction 1.7 The Right Side of the Notebook The right side of the notebook computer offers the features shown in the following figure. 1. PCMCIA Slot 2. IE E E 1394 3. 4 in 1 card slot 4. Air-Outlet Vent 5. TV Port 6. LAN Port Right Side F eatures • PCMCIA Slot An Infrared Remote Control is stored in this slot while shipping. Besides, this slot functions as a normal PCMCIA slot.
N otebook User Guide • 4 in 1 card slot The card slot supports SD, MMC, MS (Memory Stick) and MS_Pro flash memory card format. You can use either of the 4 types flash memory cards for extra storage media. Please pay attention to correct direction when you insert the flash memory card. For more detail of flash card, you can refer to Chapter 3.9 • Air-Outlet Vent E mits the heat out of your computer and keeps it within operating temperature.
1 Introduction 3. Battery Bay 5. Battery Release Latch 4. Memory Compartment Bottom of the System • Hard Disk Compartment Open this cover of this compartment to replace with other Hard Disk Drive. Please refer to Chapter 7 for how to replace it. • Battery Lock Latch Push the latch to the right side to lock and secure the battery. This action is available to release the battery when the battery lock latch has located to unlock status at the left side.
N otebook User Guide 1.9 Notebook Accessories AC Adapter The AC Adapter supplies external power to your notebook computer and charges the internal battery pack simultaneously. The AC adapter has an autoswitching design that can connect to any 100VAC ~ 240VAC power outlets. You just change the power cord if you are going to use your notebook in other countries with different connector outlets. When you connect the AC adapter, it charges the battery whether or not the notebook computer is powered on.
1 Introduction 1.10 Notebook Options DVD/ CD-RW Combo Device Pack This device pack can write data to CD-R or CD-RW CD for you to backup the data and also can read DVD/CD title. DVD dual (Dual Rewritable DVD combo) Device Pack This device pack combines following two standard packs. Using the suitable media, you can make any format of CD or DVD as you want. DVD-RW combo: This device pack can write data to CD-R or CD-RW and DVD-R or DVDRW media and also can read DVD/CD title.
Getting Started 2 2 Getting Started Y our Notebook is designed and pre-configured for easy setup and use. This chapter describes the installation steps you should follow to get the notebook up and running as quickly as possible. Contact your dealer if they have pre-installed all the needed drivers to fully operate your computer or if there is an update on the driver installation of the notebook.
N otebook User Guide 2.1 Using the Battery Pack The notebook is designed to operate with one of the following power sources: • With AC power using the AC adapter connected to an electrical outlet. • With a Lithium-Ion (Li-Ion) battery pack. You should use the AC adapter whenever it is possible, relying on the battery pack only when AC power is unavailable. Before you use your notebook computer, install and recharge the battery pack first.
Getting Started 2 Installing the Battery Pack This notebook provides the most convenient way to install the battery pack into your computer. With the extended nose directed toward the compartment, insert and push the battery pack.
N otebook User Guide When your notebook estimates that the battery only has enough charge to continue for a few minutes, it will alert you with a battery low warning beep. If you are consuming a lot of power by using the audio system, the PCMCIA slots, the hard disk drives, and optical disk drive, your notebook might run out of charge much sooner than you expect.
Getting Started 2 2.2 Connecting the AC Power Source The AC adapter provides external power source to your computer and charges the internal battery pack at the same time. The AC adapter also has an autoswitching design that can connect to any 100VAC ~ 240VAC power outlets. To connect the power adapter: 1. Plug the AC power cord into the power socket of the AC power adapter. 2. Plug the other end of the AC power cord to a live AC wall outlet. 3.
N otebook User Guide + y For the power supply of this equipment, an approved power cord has to be used. y Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices. y Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC adapter). 2.3 Starting Your Computer The Power/Resume button is found on the top of the base unit.
Getting Started 2 After the test, the screen will also display a message " press < F 2> to enter SE TUP ". You don’t need to run this program at the moment as your dealer already made the necessary settings for your computer optimal operation. Refer to Chapter 6 on running the SE TUP program later. After the test has completed, your computer will start to search and boot up the operating system from your hard drive.
N otebook User Guide first if they have already installed all the drivers along with the operating system. If not, follow the procedures below: I NSTALLING WINDOWS XP F ROM OPTICAL DISK DRIVE To install Windows XP directly from your optical disk drive, please go to Boot menu of BIOS setup menu. Use arrow key to select "CD-ROM Drive", then use " + " or " -" to move it to the top. Go to E xit menu and select " E xit Saving Changes" .
Getting Started 2 5. Click " Yes" to accept the License Agreement . 6. Tick the option " Yes, I want to restart my computer now." , and press F inish to restart your system. I NSTALLING THE VGA DE VICE DRIVE R Following is the procedure for installing the Video Accelerator 3D Adapter VGA driver to your computer: Installing VGA device driver for Windows XP 1. Click the Start button, then point to Run. The Run dialog box appears. 2. Click the Browse button and specify the directory as. " E :\Drive
N otebook User Guide 4. Click " Next" continuously to install this driver when screen displays this command. 5. Click " Yes" to accept the License Agreement. 6. Click " Next" to continue the following step. 7. Tick the option " Yes, I want to restart my computer now." , and press F inish to restart your system.. I NSTALLING THE AUDIO DE VICE DRIVE R Your notebook computer uses the Realtek Audio controller. Installing Audio device driver for Windows XP 1.
Getting Started 2. 2 Click Browse button and navigate to the directory as " E :\Drivers\WinXP\MDC Modem\ssetup.exe" 3. Click " OK" to implement the setup program to install this driver. 4. Click " OK" to install the modem driver. + Please be notified that whenever you install the TouchPad and Keyboard Controller driver , it should be install the Keyboard Controller Driver first . I NSTALLING E NE - KE YBOARD CONTROLLE R DRIVE R Installing E NE - Keyboard Controller driver for Windows XP 1.
N otebook User Guide 5. Tick the option " Yes, I want to restart my computer now." , and press F inish to restart your system. I NSTALLING THE WIRE LE SS LAN DE VICE DRIVE R AND U TILITY I NSTALLING THE WIRE LE SS LAN DRIVE R Please follow the procedures below for installing the Intel Pro Wireless LAN 2200 BG Mini PCI Adapter driver: Installing Wireless Lan driver for Windows XP 1. Click the Start button and then click Run. The Run dialog box appears. 2.
Getting Started 2 Installing LAN driver for Windows XP 1. Click the Start button, then point to Run. The Run dialog box appears. 2. Click the Browse button and specify the directory as. " E :\Drivers\Winxp\Lan\setup.exe" 3. Click " OK" to implement the setup program to install this driver. 4. Click " Next" to continue the following steps. 5. Click " Yes" to accept the License Agreement.
N otebook User Guide " E :\Drivers\WinXP\Slient Mode&RF On_Off\PM setup.exe" . 3. Click " OK" to execute the setup program. The Welcome box appears. 4. Click Next then click Install to setup this driver when screen displays this command. 5. Tick the option " F insih" to complete. 2.6 Turning off Your Computer If you are not going to use the computer for a while, it is best to turn off the power of the computer for longer use.
Using Your Notebook 3 3 Using Your Notebook T his chapter describes how to operate the standard built-in features of the notebook that you normally would use in your day-to-day computer work. If you are new to computers and to your operating system, you also need to read the manual for the operating system on how to work with your computer. It is very important to familiarize yourself well with the operating system.
N otebook User Guide 3.1 Starting Your Operating System The operating system is a must ingredient in using your computer. Without an operating system, it is like playing chess without the chessboard. It is the platform for all your software application programs to run on. The most popular operating system today is Microsoft Windows. You should have installed one operating system by your dealer unless you are an expert computer user and would need a more powerful operating system.
Using Your Notebook 1. Function Keys 3. Windows Start Menu Key 5. Windows Shortcut Key 3 2. Control Keys 4. Control Keys 6. Cursor Control Keys Keyboard Key features and operations are described below: • F unction Keys Function keys are application-driven, like F 1 through F 12 can be found on the keyboard. These keys work together with the F n key to activate special functions. Some keys (printed in blue on keypad) are preprogrammed with dual functions.
N otebook User Guide • Windows keys Use the following two keys to facilitate your work: ⇓ Start Menu key Displays the Start menu. ⇓ Shortcut/Application key Provides quick access to shortcut menus. This key acts like a right mouse button. 52 • Cursor Control keys Cursor control keys let you position the cursor on the screen where you want. In the screen, the cursor is a blinking underline, block, or vertical bar depending on the application.
Using Your Notebook 3 B ASIC KE YBOARD F UNCTIONS Keypad F unction Description < E nter> key. E xecute a command. Within many text editing application programs, the < E nter> key inserts a hard carriage return, just like what ordinary typewriter does. < E sc > key. Press this key to cancel or escape from a command or function. < Ins> key. Known as the Insert key. Press this key to toggle the keyboard data entry from insert to type over mode. < PrtScr> key. Known as the Print Screen key.
N otebook User Guide Keypad F unction Description < Ctrl> key. Known as the Control key. Used in most application program in combination with other keys to execute a certain command. + < Alt> key. Known as the Alternate key. Used in most application program in combination with other keys to execute a certain command. < F n> + < Num Lock> key. Activates the embedded 15-key numeric keypad. The keys are color coded blue. + < Caps Lock> key.
Using Your Notebook 3 SCRE E N CONTROL KE YS Keypad F unction Description < Home> key. Moves the cursor to the beginning of a screen or line. < PgUp> key. Moves the cursor up one screen at a time < PgDn> key. Moves the cursor down one screen at a time < E nd> key. Moves the cursor to the end of a screen or line. WINDOWS H OT KE YS Keypad F unction Description < Start> key. Pulls up the Windows Start menu. < Right Click> key. Performs a mouse right-click function for Windows system.
N otebook User Guide Keypad F unction Description Switches display between LCD, CRT, or + LCD and CRT simultaneously. To shut down or resume the built-in + system speaker volume. Increases the brightness of LCD display + incrementally. Decreases the brightness of LCD display incrementally. + Decreases the audio volume of the + notebook incrementally. Increases the audio volume of the + notebook incrementally. 3.
Using Your Notebook 3 The Glide Pad offers a number of options that let you customize how it functions. To access these options, locate the Control Panel and double click on the Mouse icon. The options let you control the size and color of the cursor, cursor speed, the accepted double-click speed, and selection button orientation. The Glide Pad works a mouse pointing device replacement that is used under Windows-based operating system.
N otebook User Guide 1. The rectangular surface acts like a miniature duplicate of your display screen. To move the mouse cursor, place the finger lightly on the sensor pad and move in the desired direction. If you reach the end of the pad, lift your finger and place it back down on the other side of the pad. 2. To select an item, click on the item by pressing the left button control or by simply tapping on the surface once. A light, quick tap always works best.
Using Your Notebook 3 notebook computer model provides Wide screen 15.4” 1280x800 (Wide XGA) resolution panels. You would also probably want to set the amount of color output to display sharper images and photos. P OSSIBLE DISPLAY CONF IGURATIONS The table below shows you the possible display resolution you can set when using either the LCD display or the external monitor (CRT): Display Possible Resolution Maximum Colors Widescreen 800x600 16 million colors 15.
N otebook User Guide + If you cannot configure the display properties, change the display driver first as mentioned on Section 5 " Installing the Notebook Device Drivers" of Chapter 2 in this manual. Consult your dealer for the latest Windows VGA driver. 3.5 Knowing the Power Saving Features One of the great features in your notebook computer aside from its superior performance is the ability to save energy power.
Using Your Notebook 3 of power indicator flashes. To resume your working again, you can press the power button to return your work to the screen where you left off. Hibernation Mode In Hibernation mode, all system devices are powered down and the contents of RAM are stored on your hard drive. Hibernate mode uses less power than Standby mode, but takes a bit longer time to resume. When your notebook goes into hibernation, Windows saves your entire desktop state before powering down your computer.
N otebook User Guide before using. The internal hard disk is normally assigned as Drive C after formatting. Sometimes divided into two partitions, adding a Drive D. Since your computer supports different hard disk capacities (up to 80 GB), you also need to setup the disk type first on your computer’s BIOS SE TUP program before formatting the disk drive. Your computer supports Auto-detect hard disk type, so you do not need to set it manually. Your dealer should already have done all of this for you.
Using Your Notebook 2. 3 Place the disc on top of the CD tray with the label side facing up. Gently press the compact disc onto the center spindle to secure the disc. 3. To remove the disc, press on the center spindle and pull up the disc from the side until the disc snaps out of the spindle lock. + If the eject function is disabled by software or a power failure occurs, the E mergency E ject Hole allows you to manually remove a CD from the reader. 4.
N otebook User Guide • Always pick up the CD by its edges. • Avoid scratching or soiling either side of the CD. • Do not write with the hard ball-point pen or apply labels on either side of the CD. • Keep the CD away from direct sunlight or high temperatures. • Clean fingerprints or dust from the CD by wiping it with a soft cloth. The above points also apply to other optical storage media. + The Combo drive is a Class 1 Laser Product. 3.
Using Your Notebook Type II 5.0 mm Fax/Modem & Network Cards Type III 10.5 mm Hard Disks (ATA Cards) 3 Type II Cards Type II card has a thickness of 5.0 millimeters (mm). Type II cards are often storage or communications devices such as Flash Memory, LAN, and Small Computer System Interface (SCSI). Typical Type II cards include input/output (I/O) features such as modems and LANs.
N otebook User Guide The following table provides sample drive designations. Sample Drive Designations Drive letter C: Location/Device Internal hard disk D: Internal hard disk, 2nd partition E: CD/DVD/RW/Combo drive F: Slot 0, high-speed memory card Type III Cards Type III cards are thicker (10.5 mm) than Type II cards and allow no extensions. This notebook does not support Type III Card. WHAT IS CARDB US? CardBus is the high-performance 32-bit PCI bus master interface from PCMCIA.
Using Your Notebook 2. 3 Insert the side of PC card with the 68-pin socket into the PC slot. The face label of the card should also be facing up. 3. When the full length of the card is almost inside the slot, push firmly but slowly, to ensure full connection with the computer. The PC card will be detected and once the needed driver is installed, it will generate a beep sound to indicate that the card is detected.
N otebook User Guide 3. Then you can remove the inserted PC card, push the button found on the right side of the PC slot to release the eject button. Then push it again to release the PC card. 4. When the PC card has moved out a space out of the slot, hold the edges of the card and slowly slide it out. MAKING PC CARDS WORK Since PC cards come in different types and brands, making every card work on your computer may not that be easy.
Using Your Notebook + 3 Some PC cards require additional system resources. Before inserting a PC card you may have to disable either the USB port, or the 56K internal modem. Check the Windows device manager to ensure that there are no conflicts of resource amount those devices. H OT SWAPPING PC CARDS Just like floppy disk drive, your PCMCIA slot allows you to replace one PC card with another even while your computer is on.
N otebook User Guide Inserting Flash Memory Card To insert a flash memory card into the slot is similar to PCMCIA card. You only need to pay more attention whenever insert the flash memory card into the slot with the correct side. For MMC and SD card, you should position the copper connector at the bottom side. For Memory Stick card, you should position the copper connector at the topside. All of these cards should be located at the center of the slots in inserting.
Using Your Notebook 3 Removing Flash Memory Card It is similar to PCMCIA card for removing a flash memory card from the slot. You should first disable the card setting in the system as described in the PCMCIA chapter. To remove the flash memory card, you should only pull out the card by finger, there is no release button for flash memory slot.
F un with Multimedia 4 4 Fun with Multimedia T his chapter lets you make full use of all the multimedia features of your computer in having fun and excitement during work or leisure. You will learn how to mix and match the built-in sound system, use Combo drive in creating an exciting full multimedia presentation.
N otebook User Guide 4.1 Notebook Multimedia Features Your notebook computer is rich in multimedia features that make your computing fun, comfortable, exciting and easy. Your computer is well able to perform all multimedia tasks through the following: • Intel® Celeron® M Processor Dothan • Up to 2GB DDR SDRAM • DVD/CD-RW Combo or DVD Dual (Optional) • Integrated ATI RC410MB graphics engine. • 16-bit Audio Sound System with built-in speaker and microphone. 4.
F un with Multimedia • 4 Sound volume adjust by K/B hot-key 4.3 Setting up the Audio Driver Properties Before you can start using the audio capabilities of your computer, you need first to setup properly the audio driver after installing Windows. If you bought your computer with Windows pre-installed, it is most likely that your dealer have configured the sound driver for you. If not, you must refer to Chapter 2 on how to setup the sound drivers for Windows. 4.
N otebook User Guide F igure 4-1 E ntertainment Programs Group The standard multimedia components are as follows: • Windows Media Player - for playing sound, video and animation files • Sound Recorder - for recording sounds and playback • Volume Control - for adjusting the volume of mixer + For more information on how to operate these multimedia components, run the program and click on the Help menu. 4.
F un with Multimedia 4 be played back through the internal speaker or earphone jack using an external speaker, headphone, or earphone set. You can also use the files as voice annotations on many applications for more real presentation. This section will describe briefly how you can record sounds under Windows operating system. To record sounds, you need to run the Sound Recorder program from the Multimedia program groups.
N otebook User Guide 2. Click Properties in the Options main menu. 3. Click the round button for Recording and tick off each component that list in the "Shows the following Volume Controls" box. F igure 4-3 Audio Properties 4. Click OK and the Recording Control dialog box will appear. Here, you will select the input device for the recording source. If you want to record from the Combo drive with audio music, you must click on CD Player.
F un with Multimedia 4 F igure 4-4 Recording Volume Control U SING AN E XTE RNAL MICROPHONE Your computer allows you to connect an external microphone for high quality recording. The external microphone jack is found on the left side of your computer. Use only microphone with 1/8-inch mini-jack connector. Follow the same procedure for recording voice. U SING THE B UILT -IN COMBO DRIVE You would normally use the Combo drive for recording audio music from the Audio CD. Follow these steps: 1.
N otebook User Guide F igure 4-5 Play Audio CD by Windows Media Player 4. Select the starting point where you want to start recording. 5. Switch to the Sound Recorder and press the Record button. 6. Switch immediately to the Windows Media Player and press the Play button. You can adjust the volume control so you can also hear the music while in recording. 4.6 Playing Audio and Sound Your computer has built-in twin speakers to playback audio and sound.
F un with Multimedia 4 For more quality sound output, you can choose to connect an external amplified speaker or earphone from headphone jack. Always minimize the volume first before placing the phone set to your ear. U SING THE WINDOWS ME DIA P LAYE R The easiest way to playback multimedia media files is to run the Windows Media Player. Follow these steps: 1. Click on Start, point to Programs, Accessories, and then E ntertainment. 2. Click on Windows Media Player to start program. 3.
N otebook User Guide F igure 4-6 Windows Media Player 4.8 Using DVD DVD is the breakthrough in superb full-motion picture playback. One disc can contain at least 4.7GB of information, capable of holding one full-length movie with soundtracks, subtitles, and different languages. Much more, the DVD-ROM drive of your computer is backward compatible with CD-ROM drive so it allows you to use any CD as well. It also works the same as the CDROM.
F un with Multimedia 4 You can use Windows Media Player to watch DVDs on your Notebook computer. Like a conventional DVD player, by using the Player, you can skip to specific titles and chapters, play sequences in slow motion, gain access to special features, and switch audio and caption languages. In addition to these conventional DVD player tasks, you can also retrieve information about each disc from the Internet.
N otebook User Guide 4.9 Using Rewritable Optical Disk Drive DVD/CD-RW Combo or DVD+ RW combo drive is a device that can write digital data to CD-R and CD-RW or DVD+ R and DVD+ RW media. With this device, you can backup your own data to CD-R or CD-RW disc for mass data storage and safely retaining. The CD-R disc can be written several times until the CD-R is full; the CD-RW disc, furthermore, can write and erase data repeatedly. Please refer to the related user manual about the CD-RW software.
Connecting to Peripherals 5 5 Connecting to Peripherals T his chapter describes how you attach peripheral devices to your notebook. You can attach a printer or mouse; connect an external monitor and keyboard, or any other peripheral device. You will learn how to use these peripheral devices with the step-by-step instructions depicted in this chapter.
N otebook User Guide 5.1 Using the USB Port USB (Universal Serial Bus) is a hardware interface that enables you to connect multiple devices (such as printers, mice, keyboards, storage devices, joysticks, digital cameras, and video conference cameras, etc.) to your notebook computer, and up to 127 devices can be attached. Besides, USB’s hot swap capability allows everything to be plugged in and unplugged without turning the system off.
Connecting to Peripherals + 5 The USB bus distributes 0.5 amps (500 milliamps) of power through each port. For the purpose of power saving, please disconnect your USB device while not in use. 5.2 Using an External Monitor Port Your computer has a 15-pin Monitor port for supporting any external CRT or LCD color monitor. You need a display signal cable (usually provided with the monitor). One end of the cable must have a 15-pin connector for the system. To connect an external monitor: 1.
N otebook User Guide 6. If you only want to show the display on the external monitor or projector and shut off the LCD display, you can use the < F n> + < F 3> hot-key to switch display type between LCD and external monitor. Keep pressing the hot-key until you get the display to external monitor only. + Refer to Chapter 3 regarding the possible E xternal CRT resolutions and how to change the display properties. 5.
Connecting to Peripherals 5 install the driver of peripheral device to connect with the IE E E 1394 port, for details please refer to the manual that comes with your peripheral device. + Please make sure that the external IE E E 1394 HDD box you purchase on local electronic store should provide external power adapter. There are different types of IE E E 1394 HDD box and hard disk from different manufactures, the power consumption has varied range.
N otebook User Guide 2. Turn on your computer and your television set. 3. Click the Start button, then point to Settings, and click Control Panel. 4. Double-click on the Display icon and point to Setting tab. 5. Click Advanced button and point to Displays tab. You can see the TV icon on the screen. 6. Please click the red button above the TV icon. Click OK, Windows now automatically detect the TV port and enable this function. 5.
Connecting to Peripherals + 5 If you use external speakers and experience the sound distortion or feedback, please lower the volume. Some factors is caused by too close locating the microphone and speakers from each other, moving away the external audio option from the unit may also help. 5.
N otebook User Guide 5.7 Using the Wireless LAN Wireless LAN is the major breakthrough in computer communication technology. It lets user connect to the LAN environment without using any wire to traditional RJ-45 jack. User can enjoy the wireless connection within the range of Access Point (AP) of LAN. Access Point (AP) is the wireless transmission and receiving device, it generally connects to the server of a LAN environment or act as a LAN hub with wireless connection.
Connecting to Peripherals 1. 5 Locate the analog phone cable in the accessories box in notebook shipping carton. E ach end of the cable has a RJ-11 connector. 2. Connect one end of the cable into a standard wall outlet. 3. Connect the other end of the cable into the computer modem port. + The speed of data transmission is dependent on the quality of telephone lines. Digitally terminated lines improve the speed of data transmission. Contact your service provider for more information.
Customizing Your Notebook 6 6 Customizing Your Notebook Y our computer uses the Phoenix BIOS Setup program that allows you to set several system configuration in changing the way your computer performs. This includes you r system time and date, disk drive configuration and password setup. This information is then stored in the CMOS RAM and will remain permanent unless you change it again.
N otebook User Guide 6.1 Running the BIOS Setup Program Your computer is likely to have been properly setup and configured by your dealer prior to delivery. However, you may find it necessary to use the computer’s BIOS (Basic Input-Output System) Setup program to change system configuration information, such as the current date and time, or your hard disk drive type. The Setup program can be accessed when you power on the system and pressing the < F 2> function key.
Customizing Your Notebook • 6 Item Specific Help The right side of the screen. This area describes each parameter and its available settings. • Menu Bar The top line of the screen. E ach of the five selections displays its own screen. • Parameters The left side of the screen. This area lists the parameters and their current settings. • Key Status Bar The bottom part of the screen. These lines display the keys available to move the cursor, select a particular function and so forth.
N otebook User Guide 6.2 Using the Main Menu Setup Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help System Time: [07 :54 :32] , , System Date: [05/17/2005] or selects field. 4 IDE Channel 0 Master [FUJITSU MHT2040AT-(PM)] IDE Channel 1 Master [_NEC DVD+/-RW ND-6650A-S System Memory: 640 KB Extended Memory: 65535 KB CPU Type: Celeron ® M processor CPU Speed: 1500 MHz Cache RAM 1024KB BIOS Version: A.
Customizing Your Notebook • 6 System Date Allows you to set the system date using the month/date/year format. E nter the current time for reach field and use the < Tab> , < Shift> + < Tab> , or < E nter> key to move from one field or back to another. You can also change the system time from your operating system. • IDE Channel 0 Master This field display various parameters for the hard disk drive. If type [Auto] is selected, the system automatically sets these parameters.
N otebook User Guide • BIOS Version This field is for information only as the BIOS displays the BIOS version during the Power-On Self-Test (POST). 6.2.1 INTE RNAL HDD SUB-ME NU Phoenix BIOS Setup Utility Main Advanced Security Primary Master: [FUJITSU MHT2040AT-(PM)] Type: [Auto] Boot Exit Item Specific Help User = you enter LBA Format parameters of hard-disk Total Sector: 117210240 Maximum Capacity: 60012 MB drive installed at this connection.
Customizing Your Notebook 6 during power on. Set this option to None when your computer is not installed any devices. Press < E sc > to return to the Main Menu. 6.2.2 INTE RNAL OPTICAL DRIVE SUB-ME NU Phoenix BIOS Setup Utility Main Advanced Security Secondary Master: [_NEC DVD+/-RW ND-6650A-(SM) Type: [Auto] Boot Exit Item Specific Help User = you enter parameters of hard-disk Multi-Sector Transfers: [Disabled] drive installed at this LBA Mode Control: [Disabled] Connection.
N otebook User Guide 6.
Customizing Your Notebook • 6 Legacy USB Support E nable or disable the USB Bus support when in connection with USB device. • LAN Boot Control: Lets you specify E nabled or Disabled for booting the notebook from Network or not. • E xecute-Disable Bit Capability When disabled, forces the E xecute-Disable Bit Capability extended feature bit to always return 0. When disabled, forces the E xecuteDisable Bit Capability extended feature bit to always return 0.
N otebook User Guide 6.4 Security Menu Setup Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Supervisor Password Is: Clear User Password Is: Clear Set Supervisor Password [Enter] Set User Password [Enter] Password on boot [Disabled] Fixed disk boot sector [Normal] Supervisor Password controls access to the F1 Help ÇÈ Esc Exit Å--> Select Menu Enter • Select Item -/+ Change Values setup utility.
Customizing Your Notebook • 6 Set Supervisor Password Supervisor password gives you the authority in accessing the setup utility. You also need to enter this password in system booting and resuming from suspend mode. When you press < E nter> in this field, the Set Supervisor Password dialog box appears. E nter a new password with up to 8 alpha-numeric characters, and then re-enter it for confirmation. • Set User Password This field is only available when Supervisor Password has set.
N otebook User Guide 6.5 Using the Boot Setup This item allows you to set the search drive sequence where the system will try to boot up first. Phoenix BIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Boot Device priority 1: USB Floppy Drive 2: USB Storage Disk Keys used to view or 3: CD-RW/DVD-ROM configure devices: 4: Hard Drive Up or Down arrows 5: Boot from LAN Select a device. <+> and <-> moves the device up or down.
Customizing Your Notebook 6 To select the boot device, you can use the up or down arrow key, then press < + > to move up the device in the list or press < -> to move down the device in the list. To exit from this menu, press < E sc > . 6.6 How to Exit the Setup Program There are two choices to escape from the Setup program.
N otebook User Guide • Load Setup Defaults Lets you load the default values for all setup items. • Discard Changes Reverts to previously selected settings. • Save Changes Saves Setup data to CMOS. 6.7 How to Upgrade the BIOS Your computer uses E PROM Flash BIOS chip that allows you to easily upgrade the BIOS program. When you update the BIOS, any customized settings you made are lost. To upgrade the BIOS: 1. Insert the BIOS Update diskette into the diskette drive. 2.
Customizing Your Notebook 6 109
Using Options 7 7 Using Options T his chapter describes the advanced features and expandable architecture in your notebook. You can upgrade your system for specific requirements.
N otebook User Guide System Upgrade This section provides some steps in doing system upgrade for your notebook computer. The upgrade procedures include the following: 7.1 Memory Upgrade Your notebook computer offers 200-pin SODIMM (Small Outline Dual Inline Memory Module) at least 256MB DDR-SDRAM. The memory compartment is located inside your computer. The table below lists the possible combinations of different memory module and memory size.
Using Options 7 I NSTALLING ME MORY MODULE Your computer comes with standard 256 MB, 512MB or 1024MB of synchronous DDR SDRAM. You can increase system memory to a maximum of 2048 MB in the system, by installing two small outline double inline memory modules (SO-DIMMs) with installed base memory in the system. The 256MB, 512MB and 1024MB memory modules are available: To install the memory module: 1.
N otebook User Guide 5. Insert the connector of the memory module into the socket. Make sure the notch of the memory module fits the nose of the socket. y Hold the memory module at a 30-degree angle and push its connector into the memory socket of the notebook. y Press down on the edge of the memory module until the locking tabs on both sides is locked. 6. Put the DIMM door back and secure the screw on the DIMM door. 7. Turn the system over.
Using Options 7 4. Remove the crane screws located at each side of the hard disk. 5. Rotate and tighten the crane screws to the new hard disk. 6. Attach the connector to the new hard disk precisely. 7. Place the hard disk back to the compartment. 8. Cover the lid, then rotate and tighten the screws. 9. Set the boot device as DVD/CD-RW Combo drive and Primary Master as Auto on BIOS setup menu. Please refer to Chapter 6 about the setting of BIOS setup menu.
Caring for Your Notebook 8 8 Caring for Your Notebook Y our Notebook PC is a fully IBM compatible portable personal computer with the latest features in mobile computing and multimedia technology. Lightweight and compact, your Notebook PC runs on a whole wide range of general business, personal productivity, and professional applications, it is ideal for use in the office, at home, and on the road.
N otebook User Guide 8.1 Important Safety Instructions Portable computers take the most beating from end users. This section gives you detailed information about how to maintain a safe working environment while using the notebook computer. You can maintain its condition and performance by following these guidelines. Please read it carefully to ensure maximum safety. • Before cleaning the notebook computer, make sure it is disconnected from any external power supplies (i.e.
Caring for Your Notebook • 8 While unplugging the power cord, disconnect it by the plug head, not by its wire. • Make sure the socket and any extension cords you may use can support the total current load of all the connected devices. • Though your AC adapter is suitable for universal international voltage, it still requires a stable and continual power supply. Make sure the voltage of the power source when connect the notebook computer to the power outlet.
N otebook User Guide • ⇓ The notebook computer has dropped and damaged. ⇓ The notebook computer has obvious sign of breakage. Do not leave this notebook computer in an environment unconditioned. Storage temperature above 60ºC (140ºF) may damage the notebook computer. • An approved power cord has to be used for the notebook computer’s power supply. For a rated current up to 6A and an equipment weight more than 3 kg, a power cord not lighter than H05VV-F, 2G, 0.75mm2, has to be used.
Caring for Your Notebook 8 8.3 Maintaining the LCD Quality When it comes to screen problems, heat plays a big part. After a good working session, the typical routine is to shut the machine and close the cover. But the display surface - no matter what type it is - and the components inside the computer radiates heat; when you close the cover, you trap the heat against the screen. Leave the computer's cover open for about ten minutes while the heat disperses. Make this a habit.
N otebook User Guide • Use hard disk maintenance programs like Disk Defragmenter of Windows. These reorganize your hard disk by eliminating fragmentation and improving your hard disk access time. • Install a system password in your computer so others won't be able to use the hard disk. 8.5 Battery Care Guidelines The battery pack furnished with the computer requires reasonable care and handling to ensure efficient operation and maximum life.
Caring for Your Notebook • 8 You should always discharge your battery before recharging it on either of these two conditions: first, this is the first time you start to use your battery; second, you had not charge the battery for more than 2 months. To discharge the battery, please execute the "Battery Refresh" function in the BIOS Setup Utility. 8.
N 124 otebook User Guide
System Specification A APPENDIX A System Specification T his appendix gives information on the technical and hardware specifications of your computer. Please note that the information mentioned here may not be exactly the same with your computer as specification is subject to change without notice or modifying this manual. Designed with an advanced modular architecture, your Notebook PC also allows you for several levels of customization and expansion that are previously available only on desktop PCs.
N otebook User Guide P ROCE SSOR U NIT • Intel® Celeron® M Processor Dothan • Above 1.5 GHz CPU • 1MB integrated L2 cache for the processor SYSTE M ME MORY • Two 200-pin memory slots • User-upgradeable to maximum 2GB using 200-pin SODIMM 256MB, 512MB or 1024MB modules • DDR –333/400 SDRAM modules LCD DISPLAY • 15.
System Specification A STORAGE • 2.5” Format 9.
N otebook User Guide KE YBOARD • Full-sized 87-keys keyboard with Windows systems hot-keys, inverted Tcursor keys, 6 hot keys, 12 function keys, and embedded numeric keypad • Provides international language keyboard F LASH BIOS 512K Flash ROM BIOS for easy BIOS upgrade I/ O P ORTS • 1 x 15-pin VGA port • 1 x TV-Out Port (S-Video) • 4 x Universal Serial Bus (USB 2.0) • 1 x IE E E 1394 port • 1 x LAN port • 1 x Modem port WIRE LE SS DE VICE S IE E E 802.11b/g, Mini PCI 802.
System Specification A WE IGHT AND DIME NSION • 357(W) x 271(D) x 24 ~ 39(H) mm • Approximately 3.
N 130 otebook User Guide
