Signamax™ Connectivity Systems Model 065-7710 8-Port 10/100BaseT/TX +2SFP Managed Switch User’s Guide
Signamax™ Connectivity Systems Model 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch User’s Guide Release 2.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Table of Contents CAUTION -------------------------------------------------------------------------------------- VI ELECTRONIC EMISSION NOTICES --------------------------------------------------------- VI CHAPTER 1. INTRODUCTION--------------------------------------------------------- 2 1-1. OVERVIEW OF 8 FAST ETHERNET + 2 GIGABIT L2 MANAGED SWITCH -------- 2 1-2.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-3. SNMP CONFIGURATION -------------------------------------------------------------59 3-4. DHCP BOOT --------------------------------------------------------------------------61 3-5. IGMP SNOOPING ---------------------------------------------------------------------62 3-6. VLAN ----------------------------------------------------------------------------------66 3-6-1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Revision History Release Date Revision 2.02 2.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch v
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always: • Touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit device. • Pick up the device by holding it on the left and right edges only.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch About this user’s manual In this user’s manual, it will not only tell you how to install and connect your network system but configure and monitor the 8 Fast Ethernet + 2 Gigabit L2 Managed Switch through the built-in CLI and web by RS-232 serial interface and Ethernet ports step-by-step.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 1. Introduction 1-1. Overview of 8 Fast Ethernet + 2 Gigabit L2 Managed Switch 8 Fast Ethernet + 2 Gigabit L2 Managed Switch, implemented 8 10/100Mbps TP + 2 Gigabit dual media ports with TP/SFP, is a standard switch that meets all IEEE 802.3/u/x/z Gigabit, Fast Ethernet and Ethernet specifications.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch • Key Features in the Device QoS: Support Quality of Service by the IEEE 802.1P standard. There are two priority queue and packet transmission schedule using Weighted Round Robin (WRR). User-defined weight classification of packet priority can be based on either VLAN tag on packets or user-defined port priority. Spanning Tree: Support IEEE 802.1D, IEEE 802.1w (RSTP: Rapid Spanning Tree Protocol) standards.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 1-2. Checklist Before you start installing the switch, verify that the package contains the following: ⎯ ⎯ ⎯ ⎯ ⎯ 8 Fast Ethernet + 2 Gigabit L2 Managed Switch Modules (optional) This User's Manual in CD-ROM AC Power Cord RS-232 Cable Please notify your sales representative immediately if any of the aforementioned items is missing or damaged. 1-3.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch • Supports 802.1Q VLAN with 256 entries.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 1-4. View of 8 Fast Ethernet + 2 Gigabit L2 Managed Switch Fig. 1-1 Full View of 8 Fast Ethernet + 2 Gigabit L2 Managed Switch with SFP Module 1-4-1. User Interfaces on the Front Panel (Button, LEDs and Plugs) There are 8 TP Fast Ethernet ports and 2 slots for optional removable modules on the front panel of the switch. LED display area, locating on the front panel, contains a CPURUN, Power LED and 10 ports working status of the switch.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch • LED Indicators LED CPURUN POWER Color System LED Green Green Function Lit when CPU is on and good Lit when AC power is on and good 10/100Mbps Ethernet TP Port 1 to 8 LED Green Lit when 100Mbps connection with remote device is good Green/ Amber Lit when 10Mbps connection with remote LNK/ACT/SPD Amber device is good Blinks when any traffic is present Off when cable connection is not good Amber Lit when full-duplex mode is active FDX/COL (TP
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 1-4-2. User Interfaces on the Rear Panel One RS-232 DB-9 interface is offered for configuration or management. And there is one AC power input socket for having the switch powered on or off. AC Line 100-240V 50/60 Hz RS-232 DB-9 Connector Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 1-5. View of the Optional Modules In the switch, Port 9, 10 includes two types of media --- TP and SFP Fiber (LC, BiDi LC…); this port supports 10/100/1000Mbps TP or 1000Mbps SFP Fiber with auto-detected function.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2. Installation 2-1. Starting 8 Fast Ethernet + 2 Gigabit L2 Managed Switch Up This section will give users a quick start for: - Hardware and Cable Installation - Management Station Installation - Software booting and configuration 2-1-1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch • TP Port and Cable Installation ⇒ In the switch, TP port supports MDI/MDI-X auto-crossover, so both types of cable, straight-through (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6 in 10/100M TP; 1, 2, 3, 4, 5, 6, 7, 8 to 1, 2, 3, 4, 5, 6, 7, 8 in Gigabit TP) and crossed-over (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 3, 6, 1, 2) can be used. It means you do not have to tell from them, just plug it. ⇒ Use Cat.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2-1-2. Installing Chassis to a 19-Inch Wiring Closet Rail Fig. 2-2 Caution: Allow a proper spacing and proper air ventilation for the cooling fan at both sides of the chassis. ⇒ ⇒ ⇒ Wear a grounding device for electrostatic discharge. Screw the mounting accessory to the front side of the switch (See Fig. 2-2). Place the Chassis into the 19-inch wiring closet rail and locate it at the proper position. Then, fix the Chassis by screwing it.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2-1-3-1. Cabling Requirements for TP Ports ⇒ For Fast Ethernet TP network connection ⎯ The grade of the cable must be Cat. 5 or Cat. 5e with a maximum length of 100 meters. ⇒ Gigabit Ethernet TP network connection ⎯ The grade of the cable must be Cat. 5 or Cat. 5e with a maximum length of 100 meters. Cat. 5e is recommended. 2-1-3-2.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2-1-3-3. Switch Cascading in Topology • Takes the Delay Time into Account Theoretically, the switch partitions the collision domain for each port in switch cascading that you may up-link the switches unlimitedly. In practice, the network extension (cascading levels & overall diameter) must follow the constraint of the IEEE 802.3/802.3u/802.3z and other 802.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Case1: All switch ports are in the same local area network. Every port can access each other (See Fig. 2-3). Fig. 2-3 No VLAN Configuration Diagram If VLAN is enabled and configured, each node in the network that can communicate each other directly is bounded in the same VLAN area. Here VLAN area is defined by what VLAN you are using. The switch supports both port-based VLAN and tag-based VLAN.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Case 2b: Port-based VLAN (See Fig.2-5). Fig. 2-5 Port-based VLAN Diagram 1. VLAN1 members could not access VLAN2, VLAN3 and VLAN4 members. 2. VLAN2 members could not access VLAN1 and VLAN3 members, but they could access VLAN4 members. 3. VLAN3 members could not access VLAN1, VLAN2 and VLAN4. 4. VLAN4 members could not access VLAN1 and VLAN3 members, but they could access VLAN2 members.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2-1-4. Configuring the Management Agent of 8 Fast Ethernet + 2 Gigabit L2 Managed Switch We offer you three ways to startup the switch management function. They are RS-232 console, CLI, and Web. Users can use any one of them to monitor and configure the switch. You can touch them through the following procedures.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2-1-4-1. Configuring the Management Agent of 8 Fast Ethernet + 2 Gigabit L2 Managed Switch through the Serial RS-232 Port To perform the configuration through RS-232 console port, the switch’s serial port must be directly connected to a DCE device, for example, a PC, through RS-232 cable with DB-9 connector. Next, run a terminal emulator with the default setting of the switch’s serial port. With this, you can communicate with the switch.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch • Set IP Address, Subnet Mask and Default Gateway IP Address Please refer to Fig. 2-7 CLI Management for details about the ex-factory setting. They are default setting of IP address. You can first either configure your PC IP address or change IP address of the switch, next to change the IP address of default gateway and subnet mask. For example, your network address is 10.1.1.0, and subnet mask is 255.255.255.0.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2-1-4-2. Configuring the Management Agent of 8 Fast Ethernet + 2 Gigabit L2 Managed Switch through the Ethernet Port There are three ways to configure and monitor the switch through the switch’s Ethernet port. They are CLI, Web browser and SNMP manager. The user interface for the last one is NMS dependent and does not cover here. We just introduce the first two types of management interface.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Fig. 2-10 the Login Screen for Web 2-1-5. IP Address Assignment For IP address configuration, there are three parameters needed to be filled in. They are IP address, Subnet Mask, Default Gateway and DNS. IP address: The address of the network device in the network is used for internetworking communication. Its address structure looks is shown in the Fig. 2-11. It is “classful” because it is split into predefined address classes or categories.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch With the classful addressing, it divides IP address into three classes, class A, class B and class C. The rest of IP addresses are for multicast and broadcast. The bit length of the network prefix is the same as that of the subnet mask and is denoted as IP address/X, for example, 192.168.1.0/24. Each class has its address range described below. Class A: Address is less than 126.255.255.255.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Class D and E: Class D is a class with first 4 MSB (Most significance bit) set to 1-1-1-0 and is used for IP Multicast. See also RFC 1112. Class E is a class with first 4 MSB set to 1-1-1-1 and is used for IP broadcast. According to IANA (Internet Assigned Numbers Authority), there are three specific IP address blocks reserved and able to be used for extending internal network.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch In this diagram, you can see the subnet mask with 25-bit long, 255.255.255.128, contains 126 members in the sub-netted network. Another is that the length of network prefix equals the number of the bit with 1s in that subnet mask. With this, you can easily count the number of IP addresses matched. The following table shows the result. Prefix Length No. of IP matched No.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch For different network applications, the subnet mask may look like 255.255.255.240. This means it is a small network accommodating a maximum of 15 nodes in the network. Default gateway: For the routed packet, if the destination is not in the routing table, all the traffic is put into the device with the designated IP address, known as default router. Basically, it is a routing policy.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 2-2. Typical Applications The 8 Fast Ethernet + 2 Gigabit L2 Managed Switch implements 8 Fast Ethernet TP ports with auto MDIX and 2 Gigabit dual media ports with SFP for removable module supported comprehensive fiber types of connection, including LC, BiDi LC for SFP. For more details on the specification of the switch, please refer to Appendix A. ⎯ ⎯ ⎯ The switch is suitable for the following applications.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Fig. 2-14 Peer-to-peer Network Connection Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3. Operation of Web-based Management This chapter instructs you how to configure and manage the switch through the web user interface it supports, to access and manage the 8 10/100Mbps TP + 2 Gigabit dual media ports with TP/SFP Fiber management Ethernet switch.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch In the switch, it supports a simple user management function allowing only one administrator to configure the system at the same time. If there are two or more users using administrator’s identity, the switch will allow the only one who logins first to configure the system. The rest of users, even with administrator’s identity, can only monitor the system. For those who have no administrator’s identity, can only monitor the system.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-1. Web Management Home Overview After you login, the switch shows you the system information as Fig. 3-2.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Fig. 3-3 port detail information In Fig. 3-3, it shows the basic information of the clicked port. With this, you’ll see the information about the port status, traffic status and bandwidth rating for egress and ingress respectively. ⎯ On the left-top corner, there is a pull-down list for Auto Logout. For the sake of security, we provide auto-logout function to protect you from illegal user as you are leaving.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Root System Port SNMP DHCP Boot IGMP Snooping VLAN MAC Table GVRP STP Trunk 802.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-1-1. System Information Function name: System Information Function description: Show the basic system information. Parameter description: Model name: The model name of this device. System description: As it is, this tells what this device is. Here, it is “8 Fast Ethernet + 2 Gigabit L2 Managed Switch”. Location: Basically, it is the location where this switch is put. User-defined.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Host IP address: The IP address of the switch. Host MAC address: It is the Ethernet MAC address of the management agent in this switch. Device Port: Show all types and numbers of the port in the switch. RAM size: The size of the DRAM in this switch. Flash size: The size of the flash memory in this switch.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-1-2. IP Configuration IP configuration is one of the most important configurations in the switch. Without the proper setting, network manager will not be able to manage or view the device. The switch supports both manual IP address setting and automatic IP address setting via DHCP server. When IP address is changed, you must reboot the switch to have the setting taken effect and use the new IP to browse for web management and CLI management.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch IP address: Users can configure the IP settings and fill in new values if users set the DHCP function “Disable”. Then, click button to update. When DHCP is disabled, Default: 192.168.1.1 If DHCP is enabled, this field is filled by DHCP server and will not allow user manually set it any more.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch DNS: It is Domain Name Server used to serve the translation between IP address and name address. The switch supports DNS client function to re-route the mnemonic name address to DNS server to get its associated IP address for accessing Internet. User can specify a DNS IP address for the switch. With this, the switch can translate a mnemonic name address into an IP address. There are two ways to specify the IP address of DNS.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-1-3. Time Configuration The switch provides manual and automatic ways to set the system time via NTP. Manual setting is simple and you just input “Year”, “Month”, “Day”, “Hour”, “Minute” and “Second” within the valid value range indicated in each item. If you input an invalid value, for example, 61 in minute, the switch will clamp the figure to 59.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch NTP: NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean Time (GMT). If use the NTP mode and select a built-in NTP time server or manually specify an user-defined NTP server as well as Time Zone, the switch will sync the time in a short after pressing button. Though it synchronizes the time automatically, NTP does not update the time periodically without user’s processing.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Day Light Saving End : This is used to set when to stop performing the daylight saving time. Mth: Range is 1 ~ 12. Default: 1 Day: Range is 1 ~ 31. Default: 1 Hour: Range is 0 ~ 23. Default: 0 Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-1-4. Account Configuration In this function, only administrator can create, modify or delete the username and password. Administrator can modify other guest identities’ password without confirming the password but it is necessary to modify the administrator-equivalent identity. Guest-equivalent identity can modify his password only.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-1-5. Management Security Through the management security configuration, the manager can do the strict setup to control the switch and limit the user to access this switch. The following rules are offered for the manager to manage the switch: Rule 1) : When no lists exists, then it will accept all connections.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Management Security Configuration Function description: The switch offers Management Security Configuration function. With this function, the manager can easily control the mode that the user connects to the switch. According to the mode, users can be classified into two types: Those who are able to connect to the switch (Accept) and those who are unable to connect to the switch (Deny).
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch IP Range: The switch supports two kinds of options for managed valid IP Range, including “Any” and “Custom”. Default is “Any”. In case that” Custom” had been chosen, you can assigned effective IP range. The valid range is 0.0.0.0~255.255.255.255. Incoming Port: The switch supports two kinds of options for managed valid Port Range, including “Any” and “Custom”. Default is “Any”.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-1-6. Virtual Stack Function name: Virtual Stack Function description: Virtual Stack Management(VSM) is the group management function. Through the proper configuration of this function, switches in the same LAN will be grouped automatically. And among these switch, one switch will be a master machine, and the others in this group will become the slave devices. VSM offers a simple centralized management function.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Fig. 3-8 Parameter description: State: It is used for the activation or de-activation of VSM. Default is Enable. Role: The role that the switch would like to play in virtual stack. Two types of roles, including master and slave are offered for option. Default is Master. Group ID: It is the group identifier (GID) which signs for VSM. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters. The maximal length is 15 characters. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-2. Port Configuration Four functions, including Port Status, Port Configuration, Simple Counter and Detail Counter are contained in this function folder for port monitor and management. Each of them will be described in detail orderly in the following sections. Port Configuration Status Configuration Simple Counter Detail Counter 3-2-1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Port Status Function Description: Report the latest updated status of all ports in this switch. When any one of the ports in the switch changes its parameter displayed in the page, it will be automatically refreshed the port current status about every 5 seconds. Parameter Description: Port No: Display the port number. The number is 1 – 10. Both port 9 and 10 are optional modules. Media: Show the media type adopted in all ports.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Speed / Duplex : Display the speed and duplex of all port. There are three speeds 10Mbps, 100Mbps and 1000Mbps supported for TP media, and the duplex supported is half duplex and full duplex. If the media is 1Gbps fiber, it is 1000Mbps supported only. The status of speed/duplex mode is determined by 1) the negotiation of both local port and link partner in “Auto Speed” mode or 2) user setting in “Force” mode.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Fig. 3-11 Parameter description of Port 9 and Port 10: Connector Type: Display the connector type, for instance, UTP, SC, ST, LC and so on. Fiber Type: Display the fiber mode, for instance, Multi-Mode, Single-Mode. Tx Central Wavelength: Display the fiber optical transmitting central wavelength, for instance, 850nm, 1310nm, 1550nm and so on.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Vendor SN (Serial Number): Show the serial number assigned by the manufacturer. Date Code: Show the date this module was made. Temperature: Show the current temperature of module. Vcc: Show the working DC voltage of module. Mon1(Bias) mA: Show the Bias current of module. Mon2(TX PWR): Show the transmit power of module. Mon3(RX PWR): Show the receiver power of module.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-2-2. Port Configuration Port Configuration is applied to change the setting of each port. In this configuration function, you can set/reset the following functions. All of them are described in detail below. Fig. 3-12 Function name: Port Configuration Function description: It is used to set each port’s operation mode. The switch supports 3 parameters for each port. They are State, Speed/Duplex and Flow Control.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Speed/Duplex: Set the speed and duplex of the port. In speed, 10/100Mbps baud rate is available for Fast Ethernet, Gigabit module in port 9, 10. If the media is 1Gbps fiber, it is always 1000Mbps and the duplex is full only. If the media is TP, the Speed/Duplex is comprised of the combination of speed mode, 10/100/1000Mbps, and duplex mode, full duplex and half duplex. The following table summarized the function the media supports.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-2-3. Simple Counter The function of Simple Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-13, the window can show all ports’ counter information at the same time. Each data field has 20-digit long. If the counting is overflow, the counter will be reset and restart counting. The data is updated every time interval defined by the user.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Rx Packet: The counting number of the packet received. Tx Collision: Number of collisions transmitting frames experienced. Rx Error Packet: Number of bad packets received.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-2-4. Detail Counter The function of Detail Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-14, the window can show only one port counter information at the same time. To see another port’s counter, you have to pull down the list of Select, then you will see the figures displayed about the port you had chosen. Each data field has 20-digit long.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Rx Unicast Packets: Show the counting number of the received unicast packet. Rx Broadcast Packets: Show the counting number of the received broadcast packet. Rx Multicast Packets: Show the counting number of the received multicast packet. Rx Pause Packets: Show the counting number of the received pause packet. Tx Collisions: Number of collisions transmitting frames experienced.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Packets 512-1023 Octets: Number of 512 ~ 1023-byte frames in good and bad packets received. Packets 1024-1522 Octets: Number of 1024-1522-byte frames in good and bad packets received. Tx Packets: The counting number of the packet transmitted. TX Octets: Total transmitted bytes. Tx Unicast Packets: Show the counting number of the transmitted unicast packet. Tx Broadcast Packets: Show the counting number of the transmitted broadcast packet.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-3. SNMP Configuration Any Network Management System (NMS) running the Simple Network Management Protocol (SNMP) can manage the Managed devices equipped with SNMP agent, provided that the Management Information Base (MIB) is installed correctly on the managed devices.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Default SNMP function : Enable Default community name for GET: public Default community name for SET: private Default community name for Trap: public Default Set function : Enable Default trap host IP address: 0.0.0.0 Default port number :162 Trap: In the switch, there are 6 trap hosts supported. Each of them has its own community name and IP address; is user-definable.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-4. DHCP Boot The DHCP Boot function is used to spread the request broadcast packet into a bigger time frame to prevent the traffic congestion due to broadcast packets from many network devices which may seek its NMS, boot server, DHCP server and many connections predefined when the whole building or block lose the power and then reboot and recover.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-5. IGMP Snooping The function, IGMP Snooping, is used to establish the multicast groups to forward the multicast packet to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast packets are running over the network. This is because a switch that does not support IGMP or IGMP Snooping can not tell the multicast packet from the broadcast packet, so it can only treat them all as the broadcast packet.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Parameter description: IGMP snooping mode selection: The switch supports three kinds of IGMP Snooping status, including “Passive”, “Active” and “Disable”. Disable: Set “Disable” mode to disable IGMP Snooping function. Default: Disable Active: In Active mode, IGMP snooping switch will periodically issue the Membership Query message to all hosts attached to it and gather the Membership report message to update the database of the Multicast table.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Allowed Group Function description: The Allowed Group function allows the IGMP Snooping to set up the IP multicast table based on user’s specific conditions. IGMP report packets that meet the items you set up will be joined or formed the multicast group. Fig. 3-18 Parameter description: IP Range: The switch supports two kinds of options for managed valid IP range, including “Any” and “Custom”. Default is “Any”.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Add: A new entry of allowed group configuration can be created after the parameters as mentioned above had been setup and then press button. Edit: The existed entry also can be modified after pressing button. Delete: Remove the existed entry of allowed group configuration from the allowed group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-6. VLAN The switch supports Tag-based VLAN (802.1q) and Port-based VLAN. Support 256 active VLANs and VLAN ID 1~4094. VLAN configuration is used to partition your LAN into small ones as your demand. Properly configuring it, you can gain not only improving security and increasing performance but greatly reducing VLAN management. 3-6-1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Symmetric Vlan: This is a Ingress Rule (Rule 1, The Ingress Filtering Rule 1 is “forward only packets with VID matching this port’s configured VID”.). For example, if port 1 receives a tagged packet with VID=100 (VLAN name=VLAN100), and if Symmetric-Vlan function is enabled, the switch will check if port 1 is a member of VLAN100. If yes, the received packet is forwarded; otherwise, the received packet is dropped.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-6-2. Tag-based Group Function name: Tag-based Group Configuration Function description: It shows the information of existed Tag-based VLAN Groups. You can also easily create, edit and delete a Tag-based VLAN group by pressing , and function buttons. User can add a new VLAN group by inputting a new VLAN name and VLAN ID after pressing button.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Add Group: Input the VLAN name, VID and then choose the member by ticking the check box beside the port No. to create a new Tag-based VLAN. As to the parameter of Untag, it stands for an egress rule of the port. If you tick the check box beside the port No., packets with this VID outgoing from this port will be untagged. Finally, press the button to have the setting taken effect. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-6-3. PVID Function name: PVID Function description: In PVID Setting, user can input VID number to each port. The range of VID number is from 1 to 4094. User also can choose ingress filtering rule (Rule 2) to each port. The Ingress Filtering Rule 2 is “drop untagged frame”. While Rule 2 is enabled, the port will discard all Untagged-frames. Fig. 3-23 Parameter description: Port 1-10: Port number. PVID: This PVID range will be 1-4094.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Drop Untag: Drop untagged frame. You can configure a given port to accept all frames (Tagged and Untagged) or just receive tagged frame. If the former is the case, then the packets with tagged or untagged will be processed. If the later is the case, only the packets carrying VLAN tag will be processed, the rest packets will be discarded.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-6-4. Port-based Group Function name: Port-based Group Configuration Function description: It shows the information of the existed Port-based VLAN Groups. You can easily create, edit and delete a Port-based VLAN group by pressing , and function buttons. User can add a new VLAN group by inputting a new VLAN name. Parameter description: VLAN Name: The name defined by administrator is associated with a VLAN group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Add Group: Create a new Port-based VLAN. Input the VLAN name and choose the member by ticking the check box beside the port No., then, press the button to have the setting taken effect. Fig. 3-25 Delete Group: Just press the button to remove the selected group entry from the Port-based group table. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-7. MAC Table MAC Table Configuration gathers many functions, including MAC Table Information, MAC Table Maintenance, Static and MAC Alias, which cannot be categorized to some function type. They are described below. Function name: MAC Table Information Function Description: Display the static or dynamic learning MAC entry and the state for the selected port. Parameter description: Port: Select the port you would like to inquire.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Port: The port that exists in the searched MAC Entry. VID: VLAN Group that MAC Entry exists. State: Display the method that this MAC Entry is built. It may show “Dynamic MAC” or “Static MAC”. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function Name: MAC Table Maintenance Function Description: This function can allow the user to set up the processing mechanism of MAC Table. An idle MAC address exceeding MAC Address Age-out Time will be removed from the MAC Table. The range of Age-out Time is 10-1000000 seconds, and the setup of this time will have no effect on static MAC addresses.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function Name: Static Setting Function Description: The function of Static is used to configure MAC’s real manners inside of the switch. Three kinds of manners including static, static with destination drop and static with source drop are contained in this function . As “static” is chosen, assign a MAC address to a specific port, all of the switch’s traffics sent to this MAC address will be forwarded to this port.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Queue (Priority): Set up the priority( 0~3) for the MAC. Forwarding Rule(Drop Policy): Static: A MAC address is assigned to a specific port, all of the switch’s traffics sent to this MAC address will be forwarded to this port. Static with Destination Drop: While the DA of the incoming packets meets the value you set up, these packets will be dropped.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: MAC Alias Function description: MAC Alias function is used to let you assign MAC address a plain English name. This will help you tell which MAC address belongs to which user in the illegal access report. At the initial time, it shows all pairs of the existed alias name and MAC address. There are three MAC alias functions in this function folder, including MAC Alias Add, MAC Alias Edit and MAC Alias Delete.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Parameter description: MAC Address: It is a six-byte long Ethernet hardware address and usually expressed by hex and separated by hyphens. For example, 00 – 40 - C7 - D6 – 00 - 02 Alias: MAC alias name you assign. Note: If there are too many MAC addresses learned in the table, we recommend you inputting the MAC address and alias name directly.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-8. GVRP Configuration GVRP is an application based on Generic Attribute Registration Protocol (GARP), mainly used to automatically and dynamically maintain the group membership information of the VLANs. The GVRP offers the function providing the VLAN registration service through a GARP application.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: GVRP Config Function description: In the function of GVRP Config, it is used to configure each port’s GVRP operation mode, in which there are seven parameters needed to be configured described below. Parameter description: GVRP State Setting: This function is simply to let you enable or disable GVRP function. You can pull down the list and click the arrow key to choose “Enable” or “Disable”.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Normal: It is Normal Registration. The Registrar responds normally to incoming GARP messages. The default setting is Normal. Fixed: It is Registration Fixed. The Registrar ignores all GARP messages, and all members remain in the registered (IN) state. Forbidden: It is Registration Forbidden. The Registrar ignores all GARP messages, and all members remain in the unregistered (EMPTY) state.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: GVRP Counter Function description: All GVRP counters are mainly divided into Received and Transmitted two categories to let you monitor the GVRP actions. Actually, they are GARP packets. Fig. 3-32 Parameter description: Received: Total GVRP Packets: Total GVRP BPDU is received by the GVRP application. Invalid GVRP Packets: Number of invalid GARP BPDU is received by the GARP application.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch LeaveEmpty Message Packets: Number of GARP BPDU with Leave Empty message is received by the GARP application. Empty Message Packets: Number of GARP BPDU with Empty message is received by the GARP application. Transmitted: Total GVRP Packets: Total GARP BPDU is transmitted by the GVRP application. Invalid GVRP Packets: Number of invalid GARP BPDU is transmitted by the GVRP application.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: GVRP Group Information Function description: To show the dynamic group member and their information. Parameter description: Current Dynamic Group Number: The number of GVRP group that are created currently. VID: VLAN identifier. When GVRP group creates, each dynamic VLAN group owns its VID. Valid range is 1 ~ 4094. Member Port: Those are the members belonging to the same dynamic VLAN group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-9. STP Configuration The Spanning Tree Protocol (STP) is a standardized method (IEEE 802.1D) for avoiding loops in switched networks. When STP is enabled, ensure that only one path is active between any two nodes on the network at a time. User can enable Spanning Tree Protocol on switch’s web management and then set up other advanced items. We recommend that you enable STP on all switches to ensure a single active path on the network. 3-9-1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch All bridges in the LAN will re-learn and determine which the root bridge is. Maximum Age time is assigned by root bridge in unit of seconds. Default is 20 seconds. Current Forward Delay: Show the current root bridge forward delay time. The value of Forward Delay time is set by root.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-9-2. STP Configuration The STP, Spanning Tree Protocol, actually includes RSTP. In the Spanning Tree Configuration, there are six parameters open for the user to configure as user’s idea. Each parameter description is listed below.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Forward Delay: You can set the root bridge forward delay time. This figure is set by root bridge only. The forward delay time is defined as the time spent from Listening state moved to Learning state and also from Learning state moved to Forwarding state of a port in bridge. The forward delay time contains two states, Listening state to Learning state and Learning state to Forwarding state.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-9-3. STP Port Configuration Function name: STP Port Setting Function description: In the STP Port Setting, one item selection and five parameters settings are offered for user’s setup. User can disable and enable each port by selecting each Port Status item. User also can set “Path Cost” and “Priority” of each port by filling in the desired value and set “Admin Edge Port” and “Admin Point To Point” by selecting the desired item.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 802.1w RSTP recommended value: (Valid range: 1 – 200,000,000) 10 Mbps : 2,000,000 100 Mbps : 200,000 1 Gbps : 20,000 Default: 0 Priority: Priority here means Port Priority. Port Priority and Port Number are mixed to form the Port ID. Port IDs are often compared in order to determine which port of a bridge would become the Root Port. The range is 0 – 240. Default is 128. Admin Edge Port: If user selects “Yes”, this port will be an edge port.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch M Check: Migration Check. It forces the port sending out an RSTP BPDU instead of a legacy STP BPDU at the next transmission. The only benefit of this operation is to make the port quickly get back to act as an RSTP port. Click button to send a RSTP BPDU from the port you specified. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-10. Trunking Configuration The Port Trunking Configuration is used to configure the settings of Link Aggregation. You can bundle more than one port with the same speed, full duplex and the same MAC to be a single logical port, thus the logical port aggregates the bandwidth of these ports. This means you can apply your current Ethernet equipments to build the bandwidth aggregation.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Per Trunking Group supports a maximum of 4 ready member-ports. Please note that some decisions will automatically be made by the system while you are configuring your trunking ports.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Port Setting/Status Function description: Port setting/status is used to configure the trunk property of each and every port in the switch system. Parameter description: Method: This determines the method a port uses to aggregate with other ports. None: A port does not want to aggregate with any other port should choose this default setting.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Aggtr: Aggtr is an abbreviation of “aggregator”. Every port is also an aggregator, and its own aggregator ID is the same as its own Port No. We can regard an aggregator as a representative of a trunking group. Ports with same Group ID and using same trunking method will have the opportunity to aggregate to a particular aggregator port. This aggregator port is usually the port with the smallest Port No. within the trunking group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Aggregator View Function description: To display the current port trunking information from the aggregator point of view. Parameter description: Aggregator: It shows the aggregator ID (from 1 to 10) of every port. In fact, every port is also an aggregator, and its own aggregator ID is the same as its own Port No.. Method: Show the method a port uses to aggregate with other ports.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: LACP Detail (LACP Aggregator Detailed Information) Function description: Show the detailed information of the LACP trunking group. Parameter description: Actor: The switch you are watching on. Partner: The peer system from this aggregator’s view. System Priority: Show the System Priority part of a system ID. MAC Address: Show the MAC Address part of a system ID. Port: Show the port number part of an LACP port ID.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: LACP System Configuration Function description: It is used to set the priority part of the LACP system ID. LACP will only aggregate together the ports whose peer link partners are all on a single system. Each system supports LACP will be assigned a globally unique System Identifier for this purpose. A system ID is a 64-bit field comprising a 48-bit MAC Address and 16-bit priority value.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-11. 802.1x Configuration 802.1x port-based network access control provides a method to restrict users to access network resources via authenticating user’s information. This restricts users from gaining access to the network resources through a 802.1x-enabled port without authentication. If a user wishes to touch the network through a port under 802.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch The overview of operation flow for the Fig. 3-41 is quite simple. When Supplicant PAE issues a request to Authenticator PAE, Authenticator and Supplicant exchanges authentication message. Then, Authenticator passes the request to RADIUS server to verify. Finally, RADIUS server replies if the request is granted or denied.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Authentication server C Fig. 3-42 Authenticator B Supplicant A The Fig. 3-43 shows the procedure of 802.1x authentication. There are steps for the login based on 802.1x port access control management. The protocol used in the right side is EAPOL and the left side is EAP. 1. At the initial stage, the supplicant A is unauthenticated and a port on switch acting as an authenticator is in unauthorized state. So the access is blocked in this stage.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 8. If user ID and password is correct, the authentication server will send a Radius-Access-Accept to the authenticator. If not correct, the authentication server will send a Radius-Access-Reject. 9. When the authenticator PAE receives a Radius-Access-Accept, it will send an EAP-Success to the supplicant. At this time, the supplicant is authorized and the port connected to the supplicant and under 802.1x control is in the authorized state.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Only MultiHost 802.1X is the type of authentication supported in the switch. In this mode, for the devices connected to this port, once a supplicant is authorized, the devices connected to this port can access the network resource through this port. 802.1x Port-based Network Access Control function supported by the switch is little bit complex, for it just support basic Multihost mode, which can distinguish the device’s MAC address and its VID.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: 802.1x State Setting Function description: This function is used to configure the global parameters for RADIUS authentication in 802.1x port security application. Parameter description: Radius Server: RADIUS server IP address for authentication. Default: 192.168.1.1 Port Number: The port number to communicate with RADIUS server for the authentication service. The valid value ranges 1-65535. Default port number is 1812.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: 802.1x Mode Setting Function description: Set the operation mode of 802.1X for each port. In this device, it supports only Multi-host operation mode. Parameter description: Port Number: Indicate which port is selected to configure the 802.1x operation mode. 802.1x Mode: 802.1x operation mode. There are two options, including Disable and Multi-host mode. Default is Disable.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Port Security Management Function description: Shows each port status. In Multihost mode, it shows the port number and its status, authorized or unauthorized. Parameter description: Disable Mode: When selecting Disable mode for a port in the function 802.1X Port Mode Configuration, the port is in the uncontrolled port state and does not apply 802.1X authenticator on it.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Param. Setting Function description: This function is used to configure the parameters for each port in 802.1x port security application. Refer to the following parameters description for details. Parameter description: Port: It is the port number to be selected for configuring its associated 802.1x parameters which are Port control, reAuthMax, txPeriod, Quiet Period, reAuthEnabled, reAuthPeriod, max.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch reAuthEnabled: Choose whether regular authentication will take place in this port. Default: ON reAuthPeriod(1-65535 s): A non-zero number seconds between the periodic re-authentication of the supplicant. Default: 3600 max. Request(1-10): The maximum of number times that the authenticator will retransmit an EAP Request to the supplicant before it times out the authentication session. The valid range: 1 – 10.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-12. Alarm Configuration Alarm Configuration Events Configuration Email/SMS Configuration Function name: Events Configuration Function description: The Trap Events Configuration function is used to enable the switch to send out the trap information while pre-defined trap events occurred. The switch offers 21 different trap events to users for switch management.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Fig. 3-48 Function name: Email/SMS Configuration Function description: Alarm configuration is used to configure the persons who should receive the alarm message via either email or SMS, or both. It depends on your settings. An email address or a mobile phone number has to be set in the web page of alarm configuration (See Fig. 3-49). Then, user can read the trap information from the email or the mobile phone.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Parameter description: Email: Mail Server: the IP address of the server transferring your email. Username: your username on the mail server. Password: your password on the mail server. Email Address 1 – 6: email address that would like to receive the alarm message. SMS: SMS Server: the IP address of the server transferring your SMS. Username: your username in ISP. Password: your username in ISP.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-13. Configuration The switch supports three copies of configuration, including the default configuration, working configuration and user configuration for your configuration management. All of them are listed and described below respectively. Default Configuration: This is the ex-factory setting and cannot be altered. In Web UI, two restore default functions are offered for the user to restore to the default setting of the switch.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-13-1. Save/Restore Function name: Save As Start Configuration Function description: Save the current configuration as a start configuration file in flash memory. Fig. 3-51 Function name: Save As User Configuration Function description: Save the current configuration as a user configuration file in flash memory. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Restore Default Configuration (includes default IP address) Function description: Restore Default Configuration function can retrieve the ex-factory setting to replace the start configuration. And the IP address of the switch will also be restored to 192.168.1.1. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Restore User Configuration Function description: Restore User Configuration function can retrieve the previous confirmed working configuration stored in the flash memory to update start configuration. When completing to restore the configuration, the system’s start configuration is updated and will be changed its system settings after rebooting the system. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-13-2. Config File Function name: Config File Function description: With this function, user can back up or reload the config files of Save As Start or Save As User via TFTP. Parameter description: Export File Path: Export Start: Export Save As Start’s config file stored in the flash. Export User-Conf: Export Save As User’s config file stored in the flash. Import File Path: Import Start: Import Save As Start’s config file stored in the flash.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-14. Security Function name: Mirror Configuration Function description: Mirror Configuration is to monitor the traffic of the network. For example, we assume that Port A and Port B are Monitoring Port and Monitored Port respectively, thus, the traffic received by Port B will be copied to Port A for monitoring. Parameter description: Mode: Used for the activation or de-activation of Port Mirror function. Default is disable.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Isolated Group Function description: Isolated Group function can let the port be independent of other ports in the Isolated group, and the communication is also forbidden between these ports. But, the ports of the Isolated group are still able to communicate with the ports of the non-Isolated group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Restricted Group Function description: The function of the Restricted Group can decide the direction of transmitting packets for the specific port. The packets received by the port with the “Ingress” mode of Restricted Group will be sent to the ports with the “Egress” mode of Restricted Group. Parameter description: Mode: Used for the activation or de-activation of Restricted Group function. Default is disable.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-15. Bandwidth Management Function name: Ingress Bandwidth Setting Function description: Ingress Bandwidth Setting function is used to set up the limit of Ingress bandwidth for each port. Fig. 3-60 Parameter description: Port No.: Choose the port that you would like this function to work on it. Valid range of the port is 1~10. Rate: Set up the limit of Ingress bandwidth for the port you choose.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Egress Bandwidth Setting Function description: Egress Bandwidth Setting function is used to set up the limit of Egress bandwidth for each port. Fig. 3-61 Parameter description: Port No.: Choose the port that you would like this function to work on it. Valid range of the port is 1~10. Rate: Set up the limit of Egress bandwidth for the port you choose.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Storm Setting Function description: Bandwidth Management function is used to set up the limit of Ingress and Egress bandwidth for each port. Fig. 3-62 Parameter description: Storm Type: Disable: Disable the function of the bandwidth storm control. Broadcast Storm Control: Enable the function of bandwidth storm control for broadcast packets.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Storm Rate : Set up the limit of bandwidth for storm type you choose. Valid value of the storm rate ranges from 1-100 with the minimum unit of 1. And only integer is acceptable. Default is 100.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-16. QoS(Quality of Service) Configuration The switch supports 5 kinds of QoS, are as follows, MAC Priority, 802.1p Priority, IP TOS Priority, and DiffServ DSCP Priority. Port Based Priority has a special name called VIP Port in the switch. Any packets enter VIP Port will have highest transmitting priority. MAC Priority act on the destination address of MAC in packets. VLAN tagged Priority field is effected by 802.1p Priority setting.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch The QoS functions as we mentioned above are able to enabled at the same time. But, the following precedence will decide whether these functions work or not. 1. enable both VIP and TOS Choose priorities of VIP and TOS. 2. enable both VIP and DSCP Choose priorities of VIP and DSCP. 3. enable both TOS and DSCP Choose "DSCP". 4. enable both VIP and DSCP Choose priorities of VIP and DSCP. 5. enable both 802.1p and TOS Choose "TOS". 6.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: QoS Global Setting Function description: When you want to use QoS function, please enable QoS Mode in advance. Then you can use MAC Priority, 802.1p Priority, IP TOS Priority, DiffServ DSCP Priority, or VIP Port functions and take effect. In this function, you can Enable QoS Mode. Choose any of Priority Control, such as 802.1p, TOS, DSCP. Moreover, you can select Scheduling Method of WRR (Weighted Round Robin) or Strict Priority.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: VIP Port Setting Function description: When the port is set as VIP Port, the packets enter this port and will have highest transmitting priority. For example, as you choose port 2 is VIP Port, simultaneously transmit packets from port 2 and port 3 to port 1 at speed of 100MB and let congestion happen. The packets for port 3 will be dropped because the packets from port 2 owns highest precedence.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: 802.1p Setting Function description: This function will affect the priority of VLAN tag. Based on priority of VLAN tag, it can arrange 0~8 priorities, priorities can map to 4 queues of the switch (queue 0~3) and possess different bandwidth distribution according to your weight setting. Parameter description: 802.1p Priority Mapping: Each Priority can select any of Queue 0 ~ Queue 3.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: D-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The field could be divided into six subfields as follows, PRECEDENCE (3 bits), DType (Delay Priority, 1 bit ), T-Type (Throughput Priority, 1bit), R-Type (Reliability Priority, 1bit ), M-Type (Monetary Cost Priority, 1bit ), and UNUSED.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: T-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The field could be divided into six subfields as follows, PRECEDENCE (3 bits), DType (Delay Priority, 1 bit ), T-Type (Throughput Priority, 1bit), R-Type (Reliability Priority, 1bit ), M-Type (Monetary Cost Priority, 1bit ), and UNUSED.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: R-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The field could be divided into six subfields as follows, PRECEDENCE (3 bits), DType (Delay Priority, 1 bit ), T-Type (Throughput Priority, 1bit), R-Type (Reliability Priority, 1bit ), M-Type (Monetary Cost Priority, 1bit ), and UNUSED.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: M-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The field could be divided into six subfields as follows, PRECEDENCE (3 bits), DType (Delay Priority, 1 bit ), T-Type (Throughput Priority, 1bit), R-Type (Reliability Priority, 1bit ), M-Type (Monetary Cost Priority, 1bit ), and UNUSED.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: DSCP Setting Function description: In the late 1990s, the IETF redefined the meaning of the 8-bit SERVICE TYPE field to accommodate a set of differentiated services (DS). Under the differentiated services interpretation, the first six bits comprise a codepoint, which is sometimes abbreviated DSCP, and the last two bits are left unused.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-17. Diagnostics Three functions, including Diagnostics, Loopback Test and Ping Test are contained in this function folder for device self-diagnostics. Each of them will be described in detail orderly in the following sections. Diagnostics Diagnostics Loopback Test Ping Test Function name: Diagnostics Function description: Diagnostics function provides a set of basic system diagnosis.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Loopback Test Function description: In the Loopback Test function, there are two different loopback tests. One is Internal Loopback Test and the other is External Loopback Test. The former test function will not send the test signal outside the switch box. The test signal only wraps around in the switch box. As to the latter test function, it will send the test signal to its link partner.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Function name: Ping Test Function description: Ping Test function is a tool for detecting if the target device is alive or not through ICMP protocol which abounds with report messages. The switch provides Ping Test function to let you know that if the target device is available or not. You can simply fill in a known IP address and then click button.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-18. TFTP Server Function name: TFTP Server Function description: Set up IP address of TFTP server. Parameter description: Specify the IP address where the TFTP server locates. Fill in the IP address of your TFTP server, then press button to have the setting taken effect. Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-19. Log This function shows the log data. The switch provides system log data for users. There are 16 private trap logs, 5 public trap logs. The switch supports total 120 log entries. For more details on log items, please refer to the section of Trap/Alarm Configuration and SNMP Configuration.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Upload Log: Upload log data through tftp. Clear Log: Clear log data.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-20. Firmware Upgrade Software upgrade tool is used to help upgrade the software function in order to fix or improve the function. The switch provides a TFTP client for software upgrade. This can be done through Ethernet. Function name: Firmware Upgrade Function description: The switch supports TFTP upgrade tool for upgrading software. If you assure to upgrade software to a newer version one, you must follow two procedures: 1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-21. Reboot We offer you many ways to reboot the switch, including power up, hardware reset and software reset. You can press the RESET button in the front panel to reset the switch. After upgrading software, changing IP configuration or changing VLAN mode configuration, then you must reboot to have the new configuration taken effect. Here we are discussing is software reset for the “reboot” in the main menu.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 3-22. Logout You can manually logout by performing Logout function. In the switch, it provides another way to logout. You can configure it to logout automatically. Function name: Logout Function description: The switch allows you to logout the system to prevent other users from the system without the permission. If you do not logout and exit the browser, the switch will automatically have you logout.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 4. Operation of CLI Management 4-1. CLI Management Refer to Chapter 2 for basic installation. The following description is the brief of the network connection. -- Locate the correct DB-9 null modem cable with female DB-9 connector. Null modem cable comes with the management switch. Refer to the Appendix B for null modem cable configuration. -- Attach the DB-9 female connector to the male DB-9 serial port connector on the Management board.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 065-7710 065-7710 Fig. 4-1 065-7710 065-7710 Fig.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 4-2. Commands of CLI To see the commands of the mode, please input “?” after the prompt, then all commands will be listed in the screen. All commands can be divided into two categories, including global commands and local commands. Global commands can be used wherever the mode you are. They are “exit”, “end”, “help”, “history”, “logout”, “save start”, “save user”, “restore default” and “restore user”.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 4-2-1. Global Commands of CLI end Syntax: end Description: Back to the top mode. When you enter this command, your current position would move to the top mode. If you use this command in the top mode, you are still in the position of the top mode. Argument: None. Possible value: None. Example: 065-7710# alarm 065-7710(alarm)# events 065-7710(alarm-events)# end 065-7710# exit Syntax: exit Description: Back to the previous mode.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch help Syntax: help Description: To show available commands. Some commands are the combination of more than two words. When you enter this command, the CLI would show the complete commands. Besides, the command would help you classify the commands between the local commands and the global ones. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch history Syntax: history [#] Description: To show a list of previous commands that you had ever run. When you enter this command, the CLI would show a list of commands which you had typed before. The CLI supports up to 256 records. If no argument is typed, the CLI would list total records up to 256. If optional argument is given, the CLI would only show the last numbers of records, given by the argument.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch logout Syntax: logout Description: When you enter this command via Telnet connection, you would logout the system and disconnect. If you connect the system through direct serial port with RS-232 cable, you would logout the system and be back to the initial login prompt when you run this command. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch restore user Syntax: restore user Description: To restore the startup configuration as user defined configuration. If restoring default successfully, the CLI would prompt if reboot immediately or not. If you press Y or y, the system would reboot immediately; others would back to the CLI system. After restoring user-defined configuration, all the changes in the startup configuration would be lost.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch save user Syntax: save user Description: To save the current configuration as the user-defined configuration. When you enter this command, the CLI would save your current configuration into the non-volatile FLASH as user-defined configuration. Argument: None. Possible value: None. Example: 065-7710# save user Saving user...
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 4-2-2. Local Commands of CLI 802.1x set max-request Syntax: set max-request Description: The maximum number of times that the state machine will retransmit an EAP Request packet to the Supplicant before it times out the authentication session. Argument: : syntax 1,5-7, available from 1 to 10 : max. times, range 1-10 Possible value: : 1 to 10 : 1-10, default is 2 Example: 065-7710(802.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set port-control Syntax: set port-control Description: To set up 802.1X status of each port. Argument: : syntax 1,5-7, available from 1 to 10 : set up the status of each port 0:ForceUnauthorized 1:ForceAuthorized 2:Auto Possible value: : 1 to 10 : 0,1 or 2 Example: 065-7710(802.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set reAuthMax Syntax: set reAuthMax Description: The number of reauthentication attempts that are permitted before the port becomes Unauthorized. Argument: : syntax 1,5-7, available from 1 to 10 : max. value , range 1-10 Possible value: : 1 to 10 : 1-10, default is 2 Example: 065-7710(802.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set state Syntax: set state Description: To configure the settings related with 802.1X Radius Server. Argument: : the IP address of Radius Server, and the IP format is xxx.xxx.xxx.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show mode Syntax: show mode Description: To display the mode of each port. Argument: None. Possible value: None. Example: 065-7710(802.1x)# show mode Port Mode ====== ============ 1 Disable 2 Multi-host 3 Disable 4 Disable 5 Disable 6 Disable : : : show parameter Syntax: show parameter Description: To display the parameter settings of each port. Argument: None. Possible value: None. Example: 065-7710(802.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show security Syntax: show security Description: To display the authentication status of each port. Argument: None. Possible value: None. Example: 065-7710(802.1x)# show security Port Mode Status ====== ============ ============== 1 Disable 2 Multi-host Unauthorized 3 Disable 4 Disable 5 Disable 6 Disable : : : show state Syntax: show state Description: To display the Radius server configuration. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch account add Syntax: add Description: To create a new guest user. When you create a new guest user, you must type in password and confirm password. Argument: : new account name Possible value: : a string must be at least 5 character. Example: 065-7710(account)# add aaaaa Password: Confirm Password: 065-7710(account)# del Syntax: del Description: To delete an existing account.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch modify Syntax: modify Description: To change the username and password of an existing account. Argument: : existing user account Possible value: None. Example: 065-7710(account)# modify aaaaa username/password: the length is from 5 to 15. Current username (aaaaa):bbbbb New password: Confirm password: Username changed successfully. Password changed successfully.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch alarm <> del mail-address Syntax: del mail-address <#> Description: To remove the e-mail address. Argument: <#>: email address number, range: 1 to 6 Possible value: <#>: 1 to 6 Example: 065-7710(alarm-email)# del mail-address 2 del server-user Syntax: del server-user Description: To remove the server, user account and password. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set server Syntax: set server Description: To set up the IP address of the email server. Argument: :email server ip address or domain name Possible value: None. Example: 065-7710(alarm-email)# set server 192.168.1.6 set user Syntax: set user Description: To set up the account of the email server. Argument: : email server account Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch <> del all Syntax: del all Description: To disable email, sms and trap of events. Argument: :del the range of email, sms and trap of events, syntax 1,5-7 Possible value: : 1~21 Example: 065-7710(alarm-events)# del all 1-3 del email Syntax: del email Description: To disable the email of the events.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch del trap Syntax: del trap Description: To disable the trap of the events. Argument: :del the range of trap, syntax 1,5-7 Possible value: : 1~21 Example: 065-7710(alarm-events)# del trap 1-3 set all Syntax: set all Description: To enable email, sms and trap of events.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set sms Syntax: set sms Description: To enable the sms of the events. Argument: :set the range of sms, syntax 1,5-7 Possible value: : 1~21 Example: 065-7710(alarm-events)# set sms 1-3 set trap Syntax: set trap Description: To enable the trap of the events.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show Syntax: show Description: The Show here is used to display the configuration of alarm event. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show (alarm) Syntax: show Description: The Show for alarm here is used to display the configuration of Trap, SMS or E-mail. Argument: None. Possible value: None. Example: 065-7710(alarm)# show email 065-7710(alarm)# show events 065-7710(alarm)# show sms <> del phone-number Syntax: del phone-number <#> Description: To delete sms phone number.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set phone-number Syntax: set phone-number <#> Description: To add sms phone number. Argument: <#>: mobile phone number, range: 1 to 6 : phone number Possible value: <#>: 1 to 6 Example: 065-7710(alarm-sms)# set phone-number 1 0968777777 set server Syntax: set server Description: To set up the IP address of sms server. Argument: : SMS server ip address or domain name Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show Syntax: show Description: To display the configuration of SMS trap event. Argument: None. Possible value: None. Example: 065-7710(alarm-sms)# show SMS Server : 192.168.1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch autologout autologout Syntax: autologout
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set storm-rate Syntax: set storm-rate Description: To set up the storm-rate of the ports. Argument: :syntax: 1,3-5, available from 1 to 5 1: Disable 2: Broadcast Storm Control 3: Multicast Storm Control 4: Unknown Unicast Storm Control 5: Broadcast, Multicast, Unknown Unicast Storm Control : 1-100. The value must be the integer. The value 100 disables broadcast storm control.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch config-file export start Syntax: export start Description: To run the export start function. Argument: None. Possible value: None. Example: 065-7710(config-file)# export start Export successful. export user-conf Syntax: export user-conf Description: To run the export user-conf function. Argument: None. Possible value: None. Example: 065-7710(config-file)# export user-conf Export successful.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch import user-conf Syntax: import user-conf Description: To run the import user-conf function. Argument: None. Possible value: None. Example: 065-7710(config-file)# import user-conf Import successful. set export-path Syntax: set export-path Description: To set up the file path and filename that user would like to export.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show Syntax: show Description: To display the information of the config file. Argument: None. Possible value: None. Example: 065-7710(config-file)# show TFTP Server IP Address: 192.168.3.111 Export Path and Filename: log/21511.txt Import Path and Filename: log/21511.txt dhcp-boot set dhcp-boot Syntax: set Description: To set up the delay time for DHCP Boot. Argument: :range syntax: 0, 1-30.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch diag diag Syntax: diag Description: Diag is used to test whether EEPROM, UART, DRAM and Flash is normal or not. Argument: None. Possible value: None. Example: 065-7710(diag)# diag EEPROM Test : OK UART Test : OK DRAM Test : OK Flash Test : OK Loopback Syntax: loopback Description: For Internal/External Loopback Test. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch firmware set upgrade-path Syntax: set upgrade-path Description: To set up the image file that will be upgraded. Argument: : upgrade file path and name Possible value: : upgrade file path and name Example: 065-7710(firmware)# set upgrade-path ES2310_v2.05.img show Syntax: show Description: To display the information of tftp server and upgrade-path and file name. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch gvrp disable Syntax: disable Description: To disable the gvrp function Argument: None. Possible value: None. Example: 065-7710(gvrp)# disable enable Syntax: enable Description: To enable the gvrp function. Argument: None. Possible value: None. Example: 065-7710(gvrp)# enable group Syntax: group Description: To enter any of gvrp group for changing gvrp group setting.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 065-7710(gvrp)# group 2 065-7710(gvrp-group-2)# set applicant 1-6 non-participant 065-7710(gvrp-group-2)# show GVRP group VID: 2 Port Applicant Registrar ---- --------------- --------1 Non-Participant Normal 2 Non-Participant Normal 3 Non-Participant Normal 4 Non-Participant Normal 5 Non-Participant Normal 6 Non-Participant Normal 7 Normal Normal : : 9 Normal Normal 10 Normal Normal 065-7710(gvrp-group-2)# set registrar 1-6 fixed 065-7710(gvrp-g
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set applicant Syntax: set applicant Description: To set default applicant mode for each port.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Example: 065-7710(gvrp)# set restricted 1-10 enable 065-7710(gvrp)# show config GVRP state: Enable Port Join Time Leave Time LeaveAll Time ---- --------- ---------- ------------1 20 60 1000 2 20 60 1000 3 20 60 1000 4 20 60 1000 5 20 60 1000 6 20 60 1000 7 20 60 1000 8 20 60 1000 9 20 60 1000 10 20 60 1000 Applicant --------------Normal Normal Normal Normal Normal Normal Normal Normal Normal Normal Registrar Restricted --------- ---------Norma
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set timer Syntax: set timer Description: To set gvrp join time, leave time, and leaveall time for each port. Argument: : port range, syntax 1,5-7, available from 1 to 10 : join timer, available from 20 to 100 : leave timer, available from 60 to 300 : leaveall timer, available from 1000 to 5000 Leave Time must equal double Join Time at least.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show counter Syntax: show counter Description: To show counter of the port.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch hostname hostname Syntax: hostname Description: To set up the hostname of the switch. Argument: : hostname, max. 40 characters. Possible value: : hostname, max. 40 characters. Example: 065-7710# hostname Company Company# igmp-snooping add allowed-group Syntax: add allowed-group Description: To add the entry of allowed IP multicast group. Argument: : the range of IP multicast.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set mode Syntax: set mode Description: To set up the mode of IGMP Snooping. Argument: : 0:disable, 1:active, 2:passive Possible value: : 0,1or 2 Example: 065-7710(igmp-snooping)# set mode 2 show igmp-snooping Syntax: show igmp-snooping Description: To display IGMP snooping mode and allowed IP multicast entry. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch IP disable dhcp Syntax: disable dhcp Description: To disable the DHCP function of the system. Argument: None. Possible value: None. Example: 065-7710(ip)# disable dhcp DHCP is already stopped. enable dhcp Syntax: enable dhcp Description: To enable the system DHCP function and set DNS server via manual or auto mode. Argument: : set DNS by using manual or auto mode.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set ip Syntax: set ip Description: To set the system IP address, subnet mask and gateway. Argument: : ip address : subnet mask : default gateway Possible value: : 192.168.1.1 or others : 255.255.255.0 or others : 192.168.1.253 or others Example: 065-7710(ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch log clear Syntax: clear Description: To clear the log data. Argument: None. Possible value: None. Example: 065-7710(log)# clear disable auto-upload Syntax: disable auto-upload Description: To disable the auto-upload function. Argument: None. Possible value: None. Example: 065-7710(log)# disable auto-upload enable auto-upload Syntax: enable auto-upload Description: To enable the auto-upload function. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show Syntax: show Description: To show a list of trap log events. When any of log events happens, it will be recorded and using show command in log function to query. Up to 120 log records are supported. Argument: None. Possible value: None. Example: 065-7710(log)# show Tftp Server : 0.0.0.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch mac-table <> del Syntax: del Description: To delete the mac alias entry. Argument: : mac address, format: 00-02-03-04-05-06 Possible value: : mac address Example: 065-7710(mac-table-alias)# del 00-44-33-44-55-44 set Syntax: set Description: To set up the mac alias entry. Argument: : mac address, format: 00-02-03-04-05-06 : mac alias name, max.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch <> search Syntax: search Description: To look for the relative mac information in mac table.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch <> set aging Syntax: set aging
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Example: 065-7710(mac-table-maintain)# show Mac table ageout time: 300 seconds Port Dynamically learn limit ------ ------------------------1 8191 2 8191 3 8191 4 8191 5 8191 6 8191 7 8191 8 8191 9 8192 10 8192 <> add Syntax: add Description: To add the static mac entry.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch del Syntax: del Description: To remove the static mac entry. Argument: : mac address, format: 00-02-03-04-05-06 Possible value: : mac address Example: 065-7710(mac-table-static-mac)# del 00-02-03-04-05-06 show Syntax: show Description: To display static mac entry. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch management add Syntax: Usage: set [ ] [ ] [ ] [ ] [ ] Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 port 2-5,8 type h,s action a Synopsis: set name Mary vid 20 ip 192.168.1.1-192.168.1.90 Description: To save the adding management policy records.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch delete Syntax: delete # Description: To delete a specific record or range. Argument: [#]: a specific or range management security entry(s) Possible value: None. Example: 065-7710(management)# show #: 1 Name : Tom Type : SNMP VlanID : 2 Action : Deny IP : 192.168.1.30-192.168.1.80 Port : 1,2 065-7710(management)# delete 1 065-7710(management)# show Security rule list is empty now edit [#]: the specific management policy entry.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Example: 065-7710(management)# edit 1 065-7710(management-edit-1)# set name Tom vid 2 ip 192.168.1.30192.168.1.80 port 1-2 type s action d 065-7710(management-edit-1)# show #: 1 Name : Tom Type : SNMP VlanID : 2 Action : Deny IP : 192.168.1.30-192.168.1.80 Port : 1,2 show Syntax: show Description: To show the specific management policy record. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch port clear counter Syntax: clear counter Description: To clear all ports’ counter (include simple and detail port counter) information. Argument: None. Possible value: None. Example: 065-7710(port)# clear counter disable state Syntax: disable state Description: To disable the communication capability of the port.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set flow-control Syntax: set flow-control Description: To set up the flow control function of all ports.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show conf Syntax: show conf Description: To display the each port’s configuration about state, speed-duplex and flow control. Argument: None. Possible value: None. Example: 065-7710(port)# show conf show detail-counter Syntax: show detail-counter <#> Description: To display the detailed counting number of each port’s traffic.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Port 9 Fiber Media Information --------------------------------------------------------------------Connector Type : SFP - LC Fiber Type : Multi-mode (MM) Tx Central Wavelength : 850 Baud Rate : 1G Vendor OUI : 00:40:c7 Vendor Name : APAC Opto Vendor PN : KM28-C3S-TC-N Vendor Rev : 0000 Vendor SN : 5425010828 Date Code : 050530 Temperature : none Vcc : none Mon1 (Bias) mA : none Mon2 (TX PWR) : none Mon3 (RX PWR) : none show simple-counter Synta
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show status Syntax: show status Description: To display the port’s current status. Argument: None. Possible value: None. Example: 065-7710(port)# show status Port Media Link State Auto Nego.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch qos disable 1p Syntax: disable 1p Description: To disable 802.1p qos. Argument: None. Possible value: None. Example: 065-7710(qos)# disable 1p disable dscp Syntax: disable dscp Description: To disable IP DSCP qos. Argument: None. Possible value: None. Example: 065-7710(qos)# disable dscp disable qos Syntax: disable qos Description: To disable qos function. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch disable tos Syntax: disable tos Description: To disable IP TOS qos. Argument: None. Possible value: None. Example: 065-7710(qos)# disable tos enable 1p Syntax: enable 1p Description: To enable 802.1p qos. Argument: None. Possible value: None. Example: 065-7710(qos)# enable 1p enable dscp Syntax: enable dscp Description: To enable IP DSCP qos. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch enable qos Syntax: enable qos Description: To enable qos function. Argument: None. Possible value: None. Example: 065-7710(qos)# enable qos enable tos Syntax: enable tos Description: To enable IP TOS qos. Argument: None. Possible value: None. Example: 065-7710(qos)# enable tos set dscp Syntax: set dscp [] [] [] [] Description: To set IP DSCP qos weighting for 4 queues.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set pri-tag Syntax: set pri-tag [] [] [] [] Description: To set 802.1p qos weighting for 4 queues. Argument: : queue level, q0: queue 0; q1: queue 1; q2: queue 2; q3: queue 3. : priority level. One queue has been assigned 2 different priorities. You don't need to use all of queues, but must assign queues in order. Syntax: 1,2 or 2,5-7, available from 0 to 7.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Possible value: : 0~3 : 0 to 7 Example: 065-7710(qos)# set tos 0 q0 1 q1 2 q2 4 q3 6 set vip Syntax: set vip Description: To set vip port for strict priority. Argument: : syntax 1,5-7, available from 1 to 10 : enable/disable vip port for each port. 1: enable. 0: disable.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch DiffServ Queue DiffServ Queue DiffServ Queue DiffServ Queue ---------- ------- ---------- ------- ---------- ------- ---------- -----0 0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 10 0 11 0 12 0 13 0 14 0 15 0 16 1 17 1 18 1 19 1 20 1 21 1 22 1 23 1 24 1 25 1 26 1 27 1 28 1 29 1 30 1 31 1 32 2 33 2 34 2 35 2 36 2 37 2 38 2 39 2 40 2 41 2 42 2 43 2 44 2 45 2 46 2 47 2 48 3 49 3 50 3 51 3 52 3 53 3 54 3 55 3 56 3 57 3 58 3 59 3 60 3 61 3 62 3 63 3 show p
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show priority-tag Syntax: show priority-tag Description: To show 802.1p Qos configuration. Argument: None. Possible value: None. Example: 065-7710(qos)# show priority-tag 802.1p priority ==================== Global QoS mode: Enable QoS Enable 802.1p Priority Disable ip tos classification Disable ip diffserv classification Scheduling: weighted round robin method. weight: wrr 0 = 1; wrr 1 = 2; wrr 2 = 4; wrr 3 = 8. weighted range: 1~55.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show tos Syntax: show tos Description: To show IP tos Qos configuration. Argument: none Possible value: none Example: 065-7710(qos)# show tos ip tos classification ==================== Global QoS mode: Enable QoS Disable 802.1p Priority Enable ip tos classification Disable ip diffserv classification Scheduling: weighted round robin method. weight: wrr 0 = 1; wrr 1 = 2; wrr 2 = 4; wrr 3 = 8. weighted range: 1~55. P0~7: Priority 0~7.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch reboot reboot Syntax: reboot Description: To reboot the system. Argument: None. Possible value: None. Example: 065-7710# reboot security <> set Syntax: set Description: To set up the function of the isolated group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch <> disable Syntax: disable Description: To disable the function of mirror. Argument: None. Possible value: None. Example: 065-7710(security-mirror)# disable enable Syntax: enable Description: To enable the function of mirror. Argument: None. Possible value: None. Example: 065-7710(security-mirror)# enable set Syntax: set Description: To set up the monitoring port and monitored ports of the mirror function.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show Syntax: show Description: To display the current setting status of mirror. Argument: None. Possible value: None. Example: 065-7710(security-mirror)# show Mirror: Monitoring Port :1 Monitored Ingress :4 Monitored Egress :2 3 <> set Syntax: set Description: To set up the function of restricted group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch snmp disable Syntax: disable set-community disable snmp Description: The Disable here is used for the de-activation of snmp or set-community. Argument: None. Possible value: None. Example: 065-7710(snmp)# disable set-community 065-7710(snmp)# disable snmp enable Syntax: enable set-community enable snmp Description: The Enable here is used for the activation snmp or set-community. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set Syntax: set get-community set set-community set trap <#> [port] [community] Description: The Set here is used for the setup of get-community, set-community, trap host ip, host port and trap- community.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch stp MCheck Syntax: MCheck Description: To force the port to transmit RST BPDUs. Argument: : syntax 1,5-7, available from 1 to 10 Possible value: : 1 to 10 Example: 065-7710(stp)# Mcheck 1-8 disable Syntax: disable Description: To disable the function of STP. Argument: None. Possible value: None. Example: 065-7710(stp)# disable enable Syntax: enable Description: To enable the function of STP. Argument: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set config Syntax: set config Description: To set up the parameters of STP. Argument: : priority must be a multiple of 4096,available from 0 to 61440. : available from 1 to 10. : available from 6 to 40. : available from 4 to 30. Note: 2*(Forward Delay -1) >= Max. Age Max.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show config Syntax: show config Description: To display the STP configuration data. Argument: None. Possible value: None. Example: 065-7710(stp)# show config STP State Configuration : Spanning Tree Protocol : Enabled Bridge Priority (0-61440) : 61440 Hello Time (1-10 sec) : 2 Max. Age (6-40 sec) : 20 Forward Delay (4-30 sec) : 15 Force Version : RSTP show port Syntax: show port Description: To display the port information of STP.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show status Syntax: show status Description: To display of the status of STP. Argument: None. Possible value: None. Example: 065-7710(stp)# show status STP Status : STP State Bridge ID Bridge Priority Designated Root Designated Priority Root Port Root Path Cost Current Max.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch system set contact Syntax: set contact Description: To set the contact description of the switch. Argument: :string length up to 40 characters. Possible value: : A, b, c, d, ... ,z and 1, 2, 3, …. etc. Example: 065-7710(system)# set contact Taipei set device-name Syntax: set device-name Description: To set the device name description of the switch.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show Syntax: show Description: To display the basic information of the switch. Argument: None. Possible value: None. Example: 065-7710(system)# show Model Name : 065-7710 System Description : 8 Fast Ethernet + 2 Gigabit L2 Managed Switch Location : Contact : Device Name : 065-7710 System Up Time : 0 Days 5 Hours 9 Mins 19 Secs Current Time : Mon Dec 26 15:05:14 2005 BIOS Version : v1.05 Firmware Version : v2.02 Hardware-Mechanical Version : v1.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch tftp set server Syntax: set server Description: To set up the IP address of tftp server. Argument: : the IP address of tftp server Possible value: : tftp server IP Example: 065-7710(tftp)# set server 192.168.3.111 show Syntax: show Description: To display the information of tftp server. Argument: None. Possible value: None. Example: 065-7710(tftp)# show Tftp Server : 192.168.3.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch time set daylightsaving Syntax: set daylightsaving
Description: To set up the daylight saving.Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set ntp Syntax: set ntp Description: To set up the current time via NTP server. Argument: : ntp server ip address or domain name : time zone (GMT), range: -12 to +13 Possible value: : -12,-11…,0,1…,13 Example: 065-7710(time)# set ntp clock.via.net 8 Synchronizing...
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch trunk del trunk Syntax: del trunk Description: To remove the trunk port. Argument: : syntax 1,5-7, available from 1 to 10 Possible value: : 1 to 10 Example: 065-7710(trunk)# del trunk 1 set hash Syntax: set hash Description: To set up trunk hash method. Argument: : lacp hash method 0: DA and SA 1: SA 2: DA Note : This hash method applies to both LACP and static trunk.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set trunk Syntax: set trunk Description: To set up the status of trunk, including the group number and mode of the trunk as well as LACP mode.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show lacp-config Syntax: show lacp-config Description: To display the value of LACP Priority. Argument: None. Possible value: None. Example: 065-7710(trunk)# show lacp-config LACP System Priority : 33333 Hash Method : DA show lacp-detail Syntax: show lacp-detail Description: To display the detailed information of the LACP trunk group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show status Syntax: show status Description: To display the aggregator status and the settings of each port. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch vlan del port-group Syntax: del port-group Description: To delete the port-based vlan group. Argument: : port-vlan name Possible value: : port-vlan name Example: 065-7710(vlan)# del port-group vlan-2 del tag-group Syntax: del tag-group Description: To delete the tag-based vlan group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch disable drop-untag Syntax: disable drop-untag Description: To disable drop-untag. Argument: : which port(s) you want not to drop untagged frames. Syntax: 1,5-7, available from 1 to 10 Possible value: : 1 to 10 Example: 065-7710(vlan)# disable drop-untag 2,4,5-7 disable svl Syntax: disable svl Description: To enable Independent VLAN Learning. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch enable double-tag Syntax: enable double-tag Description: To enable double-tag. Argument: None. Possible value: None. Example: 065-7710(vlan)# enable double-tag enable drop-untag Syntax: enable drop-untag Description: To enable drop-untag. Argument: : which port(s) you want to drop untagged frames.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch enable symmetric Syntax: enable symmetric Description: To drop frames from the non-member port. Argument: None. Possible value: None. Example: 065-7710(vlan)# enable symmetric set mode Syntax: set mode Description: To switch vlan mode between port-based and tag-based modes.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set pvid Syntax: set pvid Description: To set vlan PVID and port pripority. Argument: : which port(s) you want to set PVID(s).
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show config Syntax: show config Description: To display the current vlan mode, Symmetric vlan, SVL and Double tag states. Argument: None. Possible value: None. Example: 065-7710(vlan)# show config Current vlan mode:Tag-based vlan Global setting: Symmetric vlan : Disable (Asymmetric) SVL : Disable (IVL) Double tag : Disable show group Syntax: show group Description: To display vlan mode and vlan group.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch show pvid Syntax: show pvid Description: To display pvid, priority and drop untag result. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch vs disable Syntax: disable Description: To disable the virtual stack. Argument: None. Possible value: None. Example: 065-7710(vs)# disable enable Syntax: enable Description: To enable the virtual stack. Argument: None. Possible value: None. Example: 065-7710(vs)# enable set gid Syntax: set gid Description: To set the group id.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch set role Syntax: set role Description: To set role. Argument: : master: act as master, slave : act as slave Possible value: : master or slave Example: 065-7710(vs)# set role master show Syntax: show Description: To display the configuration of the virtual stack. Argument: None. Possible value: None.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch 5. Maintenance 5-1. Resolving No Link Condition The possible causes for a no link LED status are as follows: z The attached device is not powered on z The cable may not be the correct type or is faulty z The installed building premise cable is faulty z The port may be faulty 5-2. Q&A 1. Computer A can connect to Computer B, but cannot connect to Computer C through the Managed Switch. 9 The network device of Computer C may fail to work.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Appendix A Technical Specifications Features • The switch included 8-Port 10/100Mbps TP and 2-Port Gigabit Dual Media TP/SFP. • Supports 8-port 10/100M TP ports with Nway and auto MDIX function. • The switch supports 2 Gigabit dual media ports(TP/SFP) and 2 slots for removable SFP module supporting 1000M SFP fiber module. • • • • • • • • Supports on-line plug/unplug SFP transceiver modules.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Hardware Specifications Standard Compliance: IEEE802.3ab / 802.3z / 802.3u / 802.3x 802.3z and 802.3ab compliant Gigabit Ethernet ports Network Interface of Option transceiver: Configuration SFP.0LC.202 SFP.0LC.212.XX SFP.0BL.621.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Diagnostic LED: System LED : Power CPURUN Per Port LED: 10/100M TP Port 1 to 8 1000M Fiber/TP Port 9,10 Power Requirement : : LINK/ACT/SPD, FDX/COL : LINK/ACT/SPD, SFP LNK AC Line Voltage : 100∼240 V Frequency : 50∼60 Hz Consumption : 11.6W Ambient Temperature : 0° to 40°C : 5% to 90% Humidity Dimensions : 44(H) × 220(W) × 130.
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Management Software Specifications System Configuration Management Agent Spanning Tree Algorithm VLAN Function Trunk Function IGMP Bandwidth Control Quality of Service (QoS) Port Security Internetworking Protocol Network Management Auto-negotiation support on 10/100Base-TX ports, Web browser or console interface can set transmission speed (10/100Mbps) and operation mode (Full/Half duplex) on each port, enable/disable any port, set VLAN gr
Signamax™ 065-7710 8-Port 10/100BaseT/TX + 2SFP Managed Switch Appendix B Null Modem Cable Specifications The DB-9 cable is used for connecting a terminal or terminal emulator to the Managed Switch’s RS-232 port to access the command-line interface. The table below shows the pin assignments for the DB-9 cable.
