Manualshelf

Installation Guide

ManualsBrandsFisher and Paykel ManualsRefrigeratorsFisher and Paykel 36 Inch Wide 16.8 Cu. Ft. Energy Star Rated Bottom Mount ActiveSmart Refrigerator with Right Hinge Door
21222324252627282930
28
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL B
SCALE 2 : 5
@3 ATTACH BOTTOM TOE KICK
For custom toe kick greater than 4” (102mm)
2
Align the air flow divider underneath the grille tabs indicator
and clip onto the vanes of the bottom grille (B).
3
With the grille tabs facing upwards, align the grille to the
bottom of the plinth where the screw holes are located
and secure with #8x5/8” pan head screws (3x) (C).
For toe kick installation at 4” (102mm)
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
B
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
Grille tabs
A
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
D
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES
2.
USE PROVIDED SCREWS TO FIX GRILL TO
3.
MATCHING HOLES ON PLASTIC PARTS
A
Cut un-required vanes from the bottom of the grille
B
Grille tabs
Front right
view
C
1
Measure the required height for the bottom grille. On a board, carefully score/cut
theun-required vanes from the bottom of the toe kick grille and discard (A).
2
Drill Ø 5/32” (4mm) holes into the dimples of the grille (B).
Repeat this process for all dimples.
4
Align the air flow divider underneath the grille tabs indicator
and clip onto the vanes of the bottom grille (D).
1
With the grille tabs facing upwards, align the grille clips to the bottom
of the plinth’s slots, then firmly push grille onto the plinth (A).