INSTALLATION INSTRUCTIONS Gas-on-glass cooktop CG301D, CG302D, CG451D, CG603D, CG604D, CG752D, CG903D & CG905D models GB IE IN PH www.fisherpaykel.com 590657C 08.
1 SAFETY AND WARNINGS WARNING! Electrical shock hazard Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it. Connection to a good earth wiring system is essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death. IMPORTANT SAFETY INSTRUCTIONS ! WARNING! Cut Hazard Take care - panel edges are sharp.
1 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS ● ● ● ● ● ● ● ● 3 This gas appliance is suitable for connection only to the gas type for which it was set at the factory, as declared on the appliance data label. It is not convertible for use on any other gas type. If in doubt, refer to the local gas network operator or gas supplier to confirm gas type at installation site. Do not modify this appliance. Do not use or store flammable materials on or near this appliance.
1 ● ● ● ● ● SAFETY AND WARNINGS Before you install the appliance, please make sure that the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance are compatible. For adjustment conditions for this appliance see ‘Gas rate summary’. a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
1 ● ● ● ● ● 5 SAFETY AND WARNINGS When you install the appliance We do not recommend you flush mount or seal this appliance into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for any costs associated with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred by doing this.
2 Dual Wok Pan support (Models with a Dual Wok only) Elbow 1/2“ BSP external thread (1) Pan support (not supplied with Dual Wok only models) Clamping brackets (4) and screws (4) PARTS SUPPLIED Mini wok Pan support (1) (CG604D only) Small pan support (1) (some models only) Wok stand (1) Fibre washer (1) LPG test point adaptor (1) (LPG models only) Installing multiple products Note: We recommend installing multiple products in separate cutouts, with a minimum 5mm space between the glass edges of th
3 GAS RATE SUMMARY-MODELS SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK DUAL WOK SEMI-RAPID AUX CG301D CG302D SEMI-RAPID CG451D CG603D SEMI-RAPID DUAL WOK MINI WOK DUAL WOK AUX CG604D CG752D SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK SEMI-RAPID DUAL WOK RAPID CG903D 7 CG905D AUX
3 GAS RATE SUMMARY All appliances are factory set for either Natural Gas or LPG and are not convertible. Check the ‘Gas type’ sticker on the base of the appliance. CG301D DUAL WOK GAS TYPE Jet size (mm) Nominal rating (kW) Nominal rating (kCal/h) NG (20 mbar)* 1.25 1.25 0.71 6.00 5162 LPG (29 mbar)* 0.80 0.80 0.50 5.50 4732 Nominal rating (g/h) (395 g/h) *Nominal pressure with at least one large burner on High.
4 PRODUCT & CABINETRY DIMENSIONS G B C H I TOP TOP Note: Gas inlet connection is located in the rear right corner.
5 CLEARANCE DIMENSIONS I J E D C F A G H B FRONT ISO CLEARANCE DIMENSIONS CG301D CG302D CG451D CG603D CG604D CG752D CG903D CG905D mm mm mm mm mm mm mm mm A Minimum clearance from left edge of cutout to nearest combustible surface 120 120 60 115 130 115 115 130 B Minimum clearance from right edge of cutout to nearest combustible surface 120 120 60 115 115 115 115 115 85 45 160 45 85 45 160 45 160 45 125 45 125 45 160 45 150 150 150 150 150 150 150 1
6 FLUSH MOUNTING INSTALLATION (OPTIONAL) B ! G G WARNING! We do not recommend flush mounting and sealing as servicing requires the cooktop to be removed from the benchtop. The owner carries all risk for flush mounting the cooktop. The owner must ensure the cooktop has been cut out from the benchtop before servicing can be carried out.
6 A FLUSH MOUNTING INSTALLATION B ROUTER THE BENCHTOP TO THE SPECIFIED DEPTH (OPTIONAL) FIT THE CLAMPING BRACKETS C MASK OFF THE AREA TO BE SILICONED 1 x4 view from below 2 3 Choose most appropriate slot for benchtop 3 mm 5 mm 16 - 50mm D APPLY SILICONE E F WIPE OFF EXCESS SILICONE IF REMOVING PRODUCT, CUT AROUND THE SILICONE TO REMOVE PRODUCT 2 min. 150 OC rated 1 Ensure silicone does not leak underneath the glass.
7 DISCARD PACKAGING 8 REMOVE THE TWO TRANSIT SCREWS Model may vary from illustrations shown Recycle responsibly 9 FIT THE ELBOW AND WASHER Floating nut 13 Fibre washer Elbow (1/2” BSP external thread) Repeat on the other side !0 LOWER GENTLY INTO THE CUTOUT
!1 !2 FIT CLAMPING BRACKETS BASED ON THE BENCHTOP THICKNESS SECURE TO BENCHTOP x4 view from below x4 16-20mm 20-30mm !3 30-40mm 40mm+ Repeat on all the other sides !4 CONNECT TO GAS SUPPLY NG Models Adjust to obtain a test point pressure of 20 mbar with all burners operating at highest setting. LPG Models Make sure to fit the supplied test point adaptor. Make sure the supply pressure is regulated to 29 mbar, with all burners operating at highest setting.
!4 INSTALLATION INSTRUCTIONS AFFIX DUPLICATE DATA LABEL SOMEWHERE ACCESSIBLE & PLUG COOKTOP IN !5 FIT PAN SUPPORTS Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Duplicate data label Model may vary !6 ● ● ● ● ● TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. Check for a well-defined blue flame without any yellow tipping.
!7 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Have you installed the clamping brackets? Have you verified that the type of model (factory-set for NG or LP) matches the type of gas at the site of installation? Have you used the fibre washer supplied? Have you sealed all connections with gas tape? Have you leak-tested all connections? Is the cooktop set to the correct working pressure? Have you affixed the supplied duplicate data plate label on an adjacent surface accessible to the customer? Is the co
17
18
www.fisherpaykel.com Copyright © Fisher & Paykel Appliances 2016. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. GB IE IN PH 590657 C 08.