INSTALLATION INSTRUCTIONS Gas Cooktop CG604DX & CG905DX models GB IE IN www.fisherpaykel.com 590877A 06.
1 ! SAFETY AND WARNINGS Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good earth wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death.
1 ●● ●● ●● ●● ●● ●● ●● ●● 2 SAFETY AND WARNINGS Do not use or store flammable materials on or near this appliance. Do not spray aerosols in the vicinity of this appliance while it is in operation. Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as these may cause serious injuries. You must remove the transit screws before installing the cooktop.
1 ●● ●● ●● ●● ●● SAFETY AND WARNINGS Before you install the appliance, please make sure that the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance are compatible. For adjustment conditions for this appliance see ‘Gas rate summary’. a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
1 ●● ●● ●● SAFETY AND WARNINGS If installed with an approved flexible hose, the hose should not come in contact with the bottom of the appliance or any sharp edges. Flexible hose assemblies should be BS 699.1 certified. Seal exposed bare edges of the cutout with an oil-based paint or moistureproof polyurethane to prevent possible moisture creeping between the cooktop trim and the benchtop.
3 SEMI-RAPID GAS RATE SUMMARY SEMI-RAPID SEMI-RAPID SEMI-RAPID All appliances are factory set for either Natural Gas or LPG. Check the ‘Gas type’ sticker on the base of the appliance. WOK MINI WOK RAPID AUX CG604DX AUX CG905DX CG604DX AUX GAS TYPE SEMI-RAPID MINI WOK Jet size (mm) Nominal rating (kW) Nominal rating (kCal/h) Jet size (mm) Nominal rating (kW) Nominal rating (kCal/h) Jet size (mm) Nominal rating (kW) Nominal rating (kCal/h) NG (20 mbar)* 0.84 1.20 1031 1.14 2.
4 PRODUCT & CABINETRY DIMENSIONS G B C H I TOP TOP Note: Gas inlet connection is located in the rear right corner.
5 CLEARANCE DIMENSIONS I I E A B D D C C A E J F B F G G H H ISO FRONT CG604DX CG905DX mm mm 130 130 115 115 160 45 160 45 150 150 650 800 650 500 650 800 650 500 70 65 70 65 250 250 min. 800 max. 850 min. 800 max.
6 7 DISCARD PACKAGING FIT THE ELBOW AND WASHER Model may vary from illustrations shown Foam Tape Adhesive side Ensure edge of tape lines up with outer edge of cooktop Floating nut Recycle responsibly 8 APPLY ADHESIVE FOAM TAPE AROUND EDGE 9 Fibre washer Elbow (1/2” BSP external thread) LOWER GENTLY INTO THE CUTOUT 2 Floating nut Fibre washer Elbow (½” BSP external thread) Foam Tape Adhesive side Ensure edge of tape lines up with outer edge of cooktop ) 8 1 Turn the cooktop upside down a
x4 2 !0 !1 FIT CLAMPING BRACKETS BASED ON THE BENCHTOP THICKNESS lifting off yellow tip Foam Tape Adhesive side x4 SECURE TO BENCHTOP good flame view from below 1 PG test point adaptor (if using LPG) 16-20mm x4 2 20-30mm 30-40mm 40mm+ Elbow (½” BSP external thread) !2 CONNECT TO GAS SUPPLY NG Arrow Repeat on all the other sides Adjust to obtain a test point pressure of 20 mbar with all the burners operating at highest setting.
!3 LEAK TESTING diameter of 10 mm and comply with relevant AS 5601/NZS 5261 requ The hose must not be kinked, subjected to abrasion or permanently d The hose must not be near or in contact with any hot surfaces (e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.) GAS GAS ●● ●● ●● Leak testing of the appliance shall be conducted according to the manufacturer’s instructions.
!4 INSTALLATION INSTRUCTIONS AFFIX DUPLICATE DATA LABEL SOMEWHERE ACCESSIBLE & PLUG COOKTOP IN !5 FIT PAN SUPPORTS Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Note: pan supports may vary Duplicate data label !6 ●● ●● ●● ●● ●● TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. Check for a well-defined blue flame without any yellow tipping.
!7 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Have you installed the clamping brackets? Have you verified that the type of model (factory-set for NG or LP) matches the type of gas at the site of installation? Have you used the fibre washer supplied? Have you sealed all connections with gas tape? Have you leak-tested all connections? Is the cooktop set to the correct working pressure? Have you affixed the supplied duplicate data plate label on an adjacent surface accessible to the customer? Is the co
13
www.fisherpaykel.com Copyright © Fisher & Paykel Appliances 2015. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. GB IE IN 590877 A 11.
