DOWNDRAFT INDUCTION COOKTOP MINIMAL CID364DTB4 INSTALLATION GUIDE US CA
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electric shock or death. READ AND SAVE THIS GUIDE General Use z z z z • Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance. • Connection to a good earth wiring system is essential and mandatory. • Alterations to the domestic wiring system must only be made by a qualified electrician.
INSTALLATION CONSIDERATIONS BEFORE INSTALLATION Please ensure the following: z z z z z z z z z z z z 4 A suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. A means of disconnection with at least a 3mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules, unless the local wiring rules allow for alternative means.
TOOLS AND COMPONENTS TOOLS REQUIRED PARTS SUPPLIED z z z Keep all packing materials until the unit has been inspected. Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher & Paykel is not responsible for shipping damage. 10 x 3.
PRODUCT DIMENSIONS b PRODUCT DIMENSIONS INCHES MM 8 9/16 217 B Overall width of cooktop 36 915 C Overall depth of cooktop 20 1/4 515 D Height of chassis 1 7/8 48 E Width of chassis 31 1/4 793 F Depth of chassis 19 3/16 488 G Depth of front overhang of cooktop glass* 9/16 14 H Depth of rear overhang of cooktop glass* 9/16 14 I Depth of left overhang of cooktop glass* 2 3/8 61 J Depth of right overhang of cooktop glass* 2 3/8 61 K Height of venting outlet 3 1/8 80 L Width
CUTOUT PROUD INSTALLATION FLUSH INSTALLATION A c A e B B c d f d g c CUTOUT DIMENSIONS e PLAN PLAN FRONT FRONT INCHES MM CUTOUT DIMENSIONS INCHES MM A Overall width of cutout 31 3/4 807 A Overall width of routered recess 32 7/8 835 B Overall depth of cutout 19 3/8 492 B Overall depth of routered recess 20 1/2 520 C Minimum depth at rear 2 50 C Overall width of cutout 31 3/4 807 D Corner radius of cutout max 3/8 max 10 D Overall depth of cutout 19 3/8 492 E Minim
CLEARANCES CLEARANCE DIMENSIONS INCHES MM Unprotected overhead cabinet centered above cooktop*† 30 762 Protected overhead cabinet centered above cooktop*† 24 610 16 5/16 415 15 3/4 40 24 610 13 330 32 11/16 830 2 50 1 9/16 39 2 50 A Minimum clearance from cook surface to: e z g z c B Minimum clearance below countertop** C Minimum clearance from side of cutout to nearest adjacent combustible surface c Minimum clearance from countertop to overhead cabinet (not directly above c
ELECTRICAL CONNECTION CONNECTION LOCATION 3 WIRE CONNECTION Before connecting the cooktop to the mains power supply check that: z z z z The domestic wiring system is suitable for the power drawn by the cooktop. The voltage corresponds to the value given in the rating plate. The power supply cable sections can withstand the load specified on the rating plate. CONNECTION MAX. CURRENT DRAW MAX.
PROUD INSTALLATION Turn the cooktop upside down on a protective cover. 1 Apply adhesive foam seal around the glass overhang, 5mm from the edge of the glass. 2 Ensure the adhesive side facing is down to form a continuous seal around the cooktop. Slot the supplied metal adapter to the rear of the cooktop. 4 Attach the four side clips to the cooktop chassis. 5 Ensure the clips are oriented correctly. 5mm 3 10 Trim the excess sealing material using a sharp cutter or trimmer knife.
INSTALL COOKTOP – FLUSH 1 adhesive 2 3 Prepare the countertop for flush installation. Use a router to cutout the edges of the countertop to specified depth (5mm). Ensure all bare edges are sealed. Refer to 'Installation Considerations'. A b 4 Align any ducting to the outlet on the cooktop before lowering it into the cutout. Tape ducting to secure. Attach an adhesive tape along the edges of the routered recess. Slot the supplied metal adapter to the rear of the cooktop.
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL Read safety and warnings in the user guide before operating the cooktop. Ensure any ducting components are secure. Specified clearance maintained. Check outlets are clear and not obstructed. Unit is level – front to back and side to side. ELECTRICAL All packaging materials have been removed. Correct Rated Over-currency protection is provided. Touch controls and displays are functioning. Adequate ground connection.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
