Installation Guide

ManualsBrandsFisher Paykel ManualsDomestic AppliancesCMOH30SS2Y

OVER THE RANGE CONVECTION MICROWAVE OVEN

INSTALLATION INSTRUCTIONS

Please read all instructions thoroughly before installing the Over the Range Microwave Oven/Hood

System. Two people are recommended to install this product.

If a new electrical outlet is required, its installation should be completed by a qualied electrician before

the microwave oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

1. MOUNTING SPACE

This Microwave Oven/Hood requires a mounting space on a wall

as shown in Figure 1.

If the space between the wall cabinets is greater than 30-inches

(36-inches or 42-inches), a Filler Panel Kit may be used to ll the

gap between the Microwave Oven/Hood system and wall cabi-

nets. The Filler Panel Kit is sold as an optional accessory; each kit

contains two 3-inch panels. The Filler Panel Kit should be installed

before the Microwave Oven/Hood is installed.

For proper installation and servicing, a 2-inch space is necessary

between the top of the range backsplash and the bottom of the

Microwave Oven/Hood system.

2. WALL CONSTRUCTION

This Microwave Oven/Hood should be mounted against and sup-

ported by a at vertical wall. The wall must be at for proper in-

stallation. If the wall is not at, use spacers to ll in the gaps. Wall

construction should be a minimum of 2" x 4" wood studding and

3/8" or more thick dry wall or plaster/lath. The mounting surfaces

must be capable of supporting weight of 110 pounds—the oven

and contents—AND the weight of all items which would normally

be stored in the top cabinet above the unit.

The unit should be attached to a minimum of one 2" x 4" wall stud.

To nd the location of the studs, one of the following methods

may be used:

A. Use a stud nder, a magnetic device which locates the nails in

the stud.

B. Use a hammer to tap lightly across the mounting surface to nd

a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a

small nail to nd the edges of the stud and then placing a mark

halfway between the edges. The center of any adjacent studs will normally be 16" or 24" to either side of this mark.

Note: In the event that the unit will be unable to be supported by any stud, it will be necessary to use special care

in the placement of the toggle bolts and top cabinet screws. See Wall Template for details. The top cabinet should

be tested to ensure it is securely attached to the wall. Place extra weight up to 110 pounds inside the top cabinet to

test the support.

3. ELECTRICAL GROUNDING INSTRUCTIONS

This appliance must be grounded. This microwave oven is equipped with a cord having a grounding wire with a

grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance

Figure 1

Figure 2

2"x 4"

Wood Studs

3/8" Dry Wall

or Plaster/lath

16" or 24"

Backsplash

30" or more

from cooking

surface

66" or more

from oor

15.5"

30"

12"

At lease 2"

Summary of content (8 pages)

PAGE 1
OVER THE RANGE convection MICROWAVE OVEN Installation Instructions Please read all instructions thoroughly before installing the Over the Range Microwave Oven/Hood System. Two people are recommended to install this product. If a new electrical outlet is required, its installation should be completed by a qualified electrician before the microwave oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2. 1.
PAGE 2
with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current. WARNING - Improper use of the grounding plug can result in a risk of electric shock. The microwave oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PIN FROM THE PLUG.
PAGE 3
6. INSTALLATION HARDWARE The INSTALLATION HARDWARE (items 1-7) packed with the oven should contain the following: ITEM Name Quantity Part code 1 Wood Screw 5 x 30 mm 6 XTSS750P35000 2 Toggle Bolt #10 - 24 x 50 mm 4 LX-BZ0195WRE0 3 Top Cabinet Screw 5 x 60 mm 2 XBRS750P60000 4 Flat Washer 30 mm diameter 2 XWHS750-16300 5 Grommet 1 LBSHC0040MRE0 6 Tapping Screw 4 x 12 mm 1 XOTS740P12000 7 Exhaust Damper Assembly 1 FFTA-B004MRK0 Figure 5 7.
PAGE 4
8. preparation of the oven 1. Rest the microwave oven on its side as shown in Figure 7. Place portion (C) of the carton underneath to protect the outercase from being damaged. 2. Remove the two screws which secure the mounting plate to the rear side of the oven. Remove the mounting plate. The two screws can be discarded. Note: If the unit you purchased does not have the mounting plate attached to the rear side of the oven, please disregard this section and continue to Section 9. 9.
PAGE 5
C. Vertical Exhaust: Outside Ventilation 1. Remove and save the 4 screws from the Fan Cover Bracket. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket as shown in Figure 13. 2. Lift the Hood Fan Unit carefully and slip wires out of cavity. See Figure 14. Mounting Plate (back side) CAUTION: Do not pull or stretch hood fan wiring. 3 Rotate the Hood Fan Unit 180˚ so that the fan blade openings are Figure 12 facing the back of the oven.
PAGE 6
10. OVEN INSTALLATION THIS MICROWAVE OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES. READ AND FOLLOW MOUNTING INFORMATION ON BOTH TOP CABINET AND WALL TEMPLATES. MOUNTING PLATE 1. Separate 4 Toggle Bolts 2, packed in the INSTALLATION HARDWARE, from the Toggle Nuts. 2. Use Wood Screws 1 to attach Mounting Plate to the stud or studs.
PAGE 7
4. Thread the power supply cord through the hole made in the bottom of the top cabinet. 5. Hang the oven on the lower edge of the mounting plate. Rotate the unit upward. See Figure 22. Take care that the power cord is able to clear the edge of the hole as the oven is rotated upward. (In the case of a non-recessed bottom in the top cabinet, the hole for the cord may need to be enlarged.) Remove the carton portions. Hang at these locations (A) 6.
PAGE 8
MOUNTING DEFLECTOR Secure the deflector with 3 Tapping screws 4 x 12mm, packed in the Installation Hardware. Deflector CHECKLIST FOR INSTALLATION 1. Make sure the unit has been installed according to all of the Installation Instructions and the Wall and Top Cabinet Templates. 2. Plug in the power cord. 3. Keep the Use and care guide. Fisher & Paykel Appliances, Inc. 5900 Skylab Road, Huntington Beach, CA 92647 Customer Care: 888.936.7872 • Fax: 714.372.7003 www.fisherpaykel.com www.dcsappliances.