DOUBLE DISHDRAWER™ DISHWASHER CONTEMPORARY DD24DTX6PX1 INSTALLATION GUIDE US CA
SAFETY AND WARNINGS WARNING! WARNING! Electric Shock Hazard Failure to follow this advice may result in electrical shock or death. Cut Hazard Failure to use caution could result in injury. • Take care – panel edges are sharp. • This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current.
SAFETY AND WARNINGS WARNING! To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance. Servicing z Do not repair or replace any part of the appliance unless specifically recommended in this guide. All other servicing should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person.
TOOLS AND COMPONENTS PARTS SUPPLIED z z z TOOLS REQUIRED Keep all packing materials until the unit has been inspected. Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher & Paykel is not responsible for shipping damage.
PRODUCT DIMENSIONS PRODUCT DIMENSIONS E INCHES MM 34 – 36 3/8 864 – 924 B Overall width 23 9/16 599 C Overall depth 22 9/16 573 D Height of chassis 22 9/16 856 E Depth of chassis 21 3/4 553 F Height of upper door panel 17 3/8 442 G Height of lower door panel 12 5/16 313 13/16 20 I Gap between door panels 5/16 8 J Depth of toe kick recess** 1 1/2 – 2 1/8 38 – 54 K Height of toe kick panel** 2 5/8 – 5 66 – 127 3/8 – 2 3/4 9 – 69 21 9/16 547 1/16 2 30 1/8 765 A Overa
CABINETRY DIMENSIONS CLEARANCES C D A E Connections can be located in an adjacent cabinet on either side of the DishDrawer™ Dishwasher*** B A PLAN B ISOMETRIC CABINETRY DIMENSIONS INCHES MM CABINETRY CLEARANCES A Minimum inside height* 34 864 A Minimum clearance to adjacent cupboard door B Inside width 23 5/8 600 B Minimum clearance to corner cupboard C Minimum inside depth** 22 3/4 578 30 762 3 15/16 – 6 5/16 100 – 160 D Recommended height of adjacent cabinetry E Height of toe
PLUMBING & ELECTRICAL CONSIDERATIONS Hose and cord lengths z z Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Preparation’ for service access requirements. If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher & Paykel drain hose extension kit which will extend the drain hoses by 3.6m (part number 525798).
HARD-WIRING (OPTIONAL) You have the option to hard-wire your DishDrawer™ Dishwasher. To do this, we recommend to remove the supplied power cord and do the hardwiring installation as close to the cavity as possible. Lift the cover upwards until you are able to pull out towards you to remove. 5 Open the lower drawer and press both locking tabs back to release. 1 Lift the drawer off the runners and carefully set aside on a protected surface. Push runners back in.
HARD WIRING (OPTIONAL) Fix the Live and Neutral wires to the terminal block and the Earth wire to the chassis. 9 L rib rear hook top view Position the cover fill valve into place before lowering the rest of the cover into position. !0 Lower the cover back into place ensuring the locking clips are aligned, the rear hook is positioned over the slot and the L rib is cleared. cover fill valve !1 Lock clips back into place by pressing down on the cover firmly. Ensure all illustrated areas are engaged.
PREPARATION SERVICE ACCESS z z z z MOISTURE PROTECTION We recommend locating the service holes on either side of the DishDrawer™ Dishwasher as shown below. If the holes are created through wood, ensure the edges are smooth and rounded If the holes are created through metal, ensure the supplied edge protector is fitted. Ensure power cord is routed through a separate service hole to the hoses.
SECURE TO CABINETRY VIA BRACKETS (METHOD A) 1 Secure all four side brackets to the DishDrawer™ Dishwasher, aligning bracket A with slot A and bracket B with slot B. 5 Partially open one of the drawers and remove the first screw cover from the trim moulding. 6 Secure to cabinetry via the brackets. Pre-drilling a pilot hole may be required depending on the cabinetry material. 7 Replace the trim cover and repeat for the remaining brackets.
SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B) Optionally, fit the two top brackets. 1 2 5 Ensure the ends of the brackets are not pushed into the chassis. It can help to reduce the loading on the feet to assist the adjustment process to decrease the height. Push the product into the cavity, pulling the hoses through as you push to avoid crushing or twisting them and taking care not to bend the legs. Push the product in the positions illustrated to avoid denting the door.
INSTALL TOE KICK 1 2 Measure toe kick height against the base of the lower tub. Carefully score toe kick at desired height. Snap off excess toe kick material and both end tabs. 3 Smooth the edges. 4 min 1/2" (12mm) 14 Slide toe kick onto the mounting rails and secure. Ensure a 12mm clearance is maintained between the floor and the toe kick, the end tabs can be used to measure this if desired. Do not over tighten the screws.
PLUMBING & ELECTRICAL CONNECTION Ø38MM STANDPIPE INSTALLATION Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to ‘Plumbing & electrical considerations’ for minimum install heights. 1 SINK TRAP/WASTE TEE INSTALLATION 1 Pull both hoses through the support guide and rest in standpipe. 2 min.
PLUMBING & ELECTRICAL CONNECTION AIR GAP INSTALLATION Connect the inlet hose to tap and handtighten into place. Install your Air Gap Kit to the benchtop. We recommend using a Dual Air Gap Kit. 1 Refer to ‘Plumbing & electrical connection’ for minimum install heights. Dual Air Gap 2 Single Air Gap Thread wire clips onto the hoses before fitting them to the hose joiner. Secure using the wire clips. Fit the joiner to the Air Gap Kit and secure using the hose clamp.
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Installation Electrical Ensure all electrical tests have been conducted in accordance with local regulations. Check all parts are installed correctly and are secure. Ensure all clearance gaps have been maintained. Ensure DishDrawer™ Dishwasher is secure and drawer opens and closes freely with no resistance. Ensure any packaging or tape securing the racks and spray arm is removed. Check the spray arm is in place, mounted correctly and rotate freely.
TROUBLESHOOTING DISPLAY POSSIBLE CAUSE WHAT TO DO No program indicator lights up when the drawer is opened z A1: Water Supply fault. RINSE + all modifiers ECO, RINSE + all modifiers GLASSWARE, ECO + all modifiers 18 1 Ensure the water supply is turned on. 2 Press once to stop the beeping, then again to clear the fault. 3 Press to resume the wash program. A3: Drawer cannot drain. The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
