INSTALLATION INSTRUCTIONS Dishwasher DW60 models NZ AU www.fisherpaykel.com 591217A 11.
1 ! SAFETY AND WARNINGS ! IMPORTANT SAFETY INSTRUCTIONS WARNING! Electrical shock hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-earthing conductor and an earthing plug.
2 3 PARTS SUPPLIED TECHNICAL DATA Technical data Check the electrical data on the rating label (located on the left-hand side of the dishwasher’s stainless steel inner door). Should the data on the rating label be different to those specified below, consider those on the rating label as correct.
5 PRODUCT DIMENSIONS C Top panel (removable) PRODUCT DIMENSIONS MM A Overall height of product with top panel in place with top panel removed* A 850 - 870** 820 - 840** B Overall width of product 597 C Overall depth of product 600 D 595 Depth of open door (measured from front of kickstrip) CABINETRY DIMENSIONS MM E Inside height of cavity PLAN with top panel in place with top panel removed* PROFILE B 855 - 875** 825 - 845** F Minimum inside width of cavity 600 G 605 Minimum inside
6 CAVITY PREPARATION IMPORTANT! Preparing the product and cabinetry To prevent possible steam damage to the cabinetry, ensure that any bare wood surrounding the dishwasher is sealed with an oil-based paint or moisture-proof polyurethane. The top panel may be removed to suit underbench cavity height. See the illustrations below. 1 IMPORTANT! The power outlet must be located in a cabinet adjacent to the dishwasher cavity. 5 Unscrew the top panel at the rear either side 6 Dia.
PLUMBING AND DRAINAGE OPTIONS. DETERMINE WHICH IS MORE SUITABLE. Dishwasher and Ø 38 mm Standpipe Dishwasher using drain hose joiner onto sink trap/waste tee 2 1 3 1 step 8 min. 750 mm 38 mm step 8 min. radius 200 mm 750 - 882.5 mm min. 120mm min. 500 mm 2 If space is limited for fixing, push hose through drain hose support to required height 750-882.
8 9 CONNECT INLET HOSE TO COLD WATER PLUG PRODUCT IN min. 10mm 3/4” BSP connector 180o No leaks! Ensure the supplied rubber washer is fitted inside the coupling. 2 1 Tighten coupling with spanner. Electrical connection Plumbing -- Water inlet connection ● ● IMPORTANT! ● The appliance should be connected to the water main using the new water inlet hose supplied. Old hoses should not be used. Do not shorten the inlet hose. ● 1 Take note of water connection requirements.
!0 ● ● TROUBLESHOOTING Excessive water remaining above the filter plate, after the rinse cycle (This can be displayed as an A20 fault) Check for a kinked drain hose, blocked waste connection, highloop not properly installed, drain hose not routed correctly or spray arms not in place. No water supply (This is displayed as an A10 fault) Check water is connected and turned on. ● The dishwasher is beeping continuously There is a fault.
!1 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Check all parts are installed. Check that the door opens and closes freely without resistance to adjacent cabinetry. Ensure that all panels and parts thereof are secure and final electrical tests have been conducted in accordance with local electrical regulations. Check that the electrical outlet is accessible and located in an adjacent cupboard. Check that the dishwasher is level. If necessary, adjust the levelling feet slightly.
9
10
www.fisherpaykel.com Copyright © Fisher & Paykel Appliances 2016. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. NZ AU 591217 A / 0120501366 A 11.
