BUILT IN OVEN OB60 models INSTALLATION GUIDE NZ AU GB IE 591785B / 1105822-ß0 05.
1 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS WARNING ! Electrical shock hazard Always disconnect the appliance from the mains power supply before carrying out any maintenance or repairs. Connection to a good earth wiring system is essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death. zz zz WARNING ! Cut Hazard Take care — panel edges are sharp.
2 PRIOR TO INSTALLATION IMPORTANT! Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture-proofing the oven cavity. Before you install the oven, make sure: zz zz zz zz zz zz zz zz zz the benchtop and oven cavity are square and level, and are the required dimensions.
PRODUCT DIMENSIONS (OB60S, OB60N MODELS) E B C A F D G H FRONT TOP OB60S MODELS OB60N MODELS (MM) (MM) a Overall height* of product 597 450** b Overall width of product 595 595 c Overall depth of product (excluding handle and knobs) 565 554 d Height of chassis 582 436 e Width of chassis 556 536 f Depth of chassis 545 534 PRODUCT DIMENSIONS G Depth of oven frame and control panel (distance between front of chassis and front of oven door, excluding knobs) H Depth of oven do
CABINETRY DIMENSIONS (OB60S, OB60N MODELS) J m i Electrical supply 16–20 mm 20 mm L K min. 2.
PRODUCT DIMENSIONS (OB60B, OB60D MODELS) B E A D C H F G i FRONT TOP OB60B MODELS OB60D MODELS (MM) (MM) a Overall height* of product 888 1077 b Overall width of product 595 595 c Overall depth of product (excluding handle and knobs) 565 565 d Height of chassis 874 1057 e Width of chassis 556 556 f Depth of chassis PRODUCT DIMENSIONS 545 545 G Depth of oven frame and control panel (distance between front of chassis and front of oven door, excluding knobs) 20 20 H Depth
CABINETRY DIMENSIONS (OB60B, OB60D MODELS) n K J Electrical supply M L 16–20 mm 20 mm min. 2.
! IMPORTANT! WARNING! When you remove the oven from the carton be careful not to damage the lower trim. The trim is important for both ventilation and to ensure the door opens fully without obstruction. Very Heavy Do not attempt to lift this product unassisted. Lifting unassisted may cause serious injury. zz zz zz DISCARD PACKAGING RESPONSIBLY Remove all packaging and dispose of it responsibly. Recycle items that you can.
230-240 V~ 3095-3370W !0 CONNECT THE OVEN TO THE MAINS SUPPLY IMPORTANT! zz zz zz zz This oven must be connected to the mains power supply only by a suitably qualified person. This oven must be earthed. L1 Before connecting the oven to the mains power supply, check that the: domestic wiring system is suitable for the power drawn by the oven (as specified on the rating plate) voltage corresponds to the value given on the rating plate.
!1 SECURE THE OVEN TO THE CABINETRY IMPORTANT! zz zz zz Do not lift the oven by the door handle. Do not over-tighten the screws. Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the cost of removing the oven, or damage caused by this removal. 1 Position the oven in the prepared cavity. 2 Open the oven door fully. 3 Secure oven to cabinetry using supplied screws. 2.
!3 TROUBLESHOOTING IF THE APPLIANCE IS NOT FUNCTIONING CORRECTLY AFTER INSTALLATION CHECK THE FOLLOWING: FF That the circuit breaker has not tripped or the fuse blown. FF Make sure that the electrical connections have been correctly made. FF Make sure that power is being supplied to the oven. FF Make sure the voltage is correct across all phases. FF If a problem occurs, consult the Troubleshooting section of the User Guide.
!4 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER: FF Make sure the oven is level and securely fitted to the cabinetry and the oven door opens and closes freely. FF Make sure all the internal packaging has been removed from the oven cavity. FF Make sure all oven vents and openings are clear and are free of any obstruction/damage. IMPORTANT! Failure to make sure all oven vents are clear may result in poor product performance.