3 0" TR I P LE STACK CO N T E MP O R A RY + MI N I MAL STYLE — Details for Flush Installation PLANNING GUIDE
COMBINATION OVERVIEW 30" Triple Stack This Planning Guide outlines the specific installation of a flush finish with front cabinetry for the 30" Triple Stack, with Contemporary and Minimal Style appliances. Cabinetry dimensions and construction contained in this document are a guideline only and will need to be adapted to suit specific location, cabinetry materials and construction methods. Please consult individual product literature for full installation instructions.
OVERALL DIMENSIONS 30" Triple Stack Product models are available in either Contemporary or Minimal style. Dimensions are the same for both styles. 56 3/4" 1442mm Overall height of products 29 15/16" 761mm Width of products 24 5/16" 617mm Minimum overall depth required for front panel and cavity DATE: November 18, 2021 IMPORTANT: Throughout this guide, dimensions may vary by ±2mm (1/16''). Read the installation guide for detailed information on installing the product.
KEY PRODUCT DECISIONS 1 2 REQUIRED 3 4 STYLE UPPER PRODUCT FUNCTION COMPANION TRIM KIT 30" OVEN SPECIFICATION DRAWER FUNCTION Companion Trim Kit, 30" (Purchased separately 24" Product) Oven, 30" 17 Function, Self-cleaning, Touchscreen (Shown with Long Trim fitted) Vacuum Seal Drawer, 30" CONTEMPORARY STYLE A timeless aesthetic featuring clean lines and complementary tonal contrasts.
KEY PRODUCT DIMENSIONS 30" Triple Stack 18 13/16" 478mm 18 13/16" 478mm 18 13/16" 478mm 29 13/16" 757mm 29 13/16" 757mm 29 13/16" 757mm 1 5/8" 42mm 1 5/8" 42mm 1 5/8" 42mm COFFEE MAKER, 24" SPEED OVEN, 24" STEAM OVEN, 24" Shown with Companion Trim Kit, 30" Shown with Companion Trim Kit, 30" Shown with Companion Trim Kit, 30" 27 3/16" 690mm 10 11/16" 271mm 29 15/16" 760mm 1 5/8" 42mm (Includes installation washer) 29 15/16" 761mm 13/16" 20mm OVEN, 30" Shown with Long Trim fitted 10 11/16"
CABINETRY OVERVIEW 30" Triple Stack This is an overview of cabinetry construction and product installation. Please see following pages for further details.
CABINETRY OVERVIEW 30" Triple Stack This is an overview of cabinetry construction and product installation. Please see following pages for further details. Adjacent Cabinet Cabinetry carcass Additional side walls 13/16" 20mm Front panel thickness used for this installation scenario. Rebate also required for Drawer if cabinetry panels thinner.
EXPLODED VIEW 30" Triple Stack IMPORTANT During installation appliances may need to be shimmed for precise alignment between products and cabinetry.
RECOMMENDED 29 15/16" 760mm IMPORTANT NOTE: MINIMUM and CRITICAL dimensions are stated to meet product installation requirements and compliance standards. Where these dimensions are not adhered to product safety and performance may be compromised, along with undesirable fit in cabinetry.
T F A R D INSTALLATION DETAILS - PROFILE VIEW 30" Triple Stack A PROFILE VIEW 18 13/16" 478mm Overall height of Coffee Maker or Cook Product with Companion Trim Kit B 27 3/16" 690mm Overall height of Oven, 30" 10 11/16" 271mm C DETAIL A PROFILE VIEW Front panel 13/16" 20mm Shelf above product DETAIL C PROFILE VIEW DETAIL B PROFILE VIEW MINIMUM 1/16" 2mm Coffee Maker or Cook Product with Companion Trim Kit Dividing Shelf* 1/2" 12mm Coffee Maker or Cook Product with Companion Trim Kit Height of D
PLAN VIEW T F A R D MINIMUM 30" 762mm Appliance cabinet width INSTALLATION DETAILS - PLAN VIEW 30" Triple Stack DETAIL D1 - COFFEE MAKER OR COOK PRODUCT with rebate PLAN VIEW Side wall, adjacent cabinet Side wall, appliance cabinet 1 5/8" 42mm Front panel 13/16" 20mm D Coffee Maker or Cook Product with Trim Kit RECOMMENDED* 30 1/16" 764mm Distance between adjacent front panels 1/8" 3.5mm *NOTE: Dimensions based on 1/16" (2mm) clearance between Oven and adjacent front panels.
THESE INSTRUCTIONS ARE FOR THESE SPECIFIC INSTALLATION SCENARIOS. OTHER CABINETRY CONSTRUCTION METHODS ARE POSSIBLE. PLEASE CONSULT PRODUCT INSTALLATION MANUALS FOR FULL PRODUCT SPECIFICATIONS AND CLEARANCE REQUIREMENTS. IMPORTANT: The product dimensions and specifications apply at the date of issue. Under our policy of continuous product improvement, these dimensions and specifications may change at any time. Dimensions may vary by ±2mm (1/16").